69 lines
3.7 KiB
C
69 lines
3.7 KiB
C
|
/**
|
||
|
|
@Generated PIC10 / PIC12 / PIC16 / PIC18 MCUs Source File
|
||
|
|
|
||
|
|
@Company:
|
||
|
|
Microchip Technology Inc.
|
||
|
|
|
||
|
|
@File Name:
|
||
|
|
mcc.c
|
||
|
|
|
||
|
|
@Summary:
|
||
|
|
This is the device_config.c file generated using PIC10 / PIC12 / PIC16 / PIC18 MCUs
|
||
|
|
|
||
|
|
@Description:
|
||
|
|
This header file provides implementations for driver APIs for all modules selected in the GUI.
|
||
|
|
Generation Information :
|
||
|
|
Product Revision : PIC10 / PIC12 / PIC16 / PIC18 MCUs - 1.81.3
|
||
|
|
Device : PIC16F1776
|
||
|
|
Driver Version : 2.00
|
||
|
|
The generated drivers are tested against the following:
|
||
|
|
Compiler : XC8 2.20 and above or later
|
||
|
|
MPLAB : MPLAB X 5.40
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
(c) 2018 Microchip Technology Inc. and its subsidiaries.
|
||
|
|
|
||
|
|
Subject to your compliance with these terms, you may use Microchip software and any
|
||
|
|
derivatives exclusively with Microchip products. It is your responsibility to comply with third party
|
||
|
|
license terms applicable to your use of third party software (including open source software) that
|
||
|
|
may accompany Microchip software.
|
||
|
|
|
||
|
|
THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER
|
||
|
|
EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY
|
||
|
|
IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS
|
||
|
|
FOR A PARTICULAR PURPOSE.
|
||
|
|
|
||
|
|
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE,
|
||
|
|
INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND
|
||
|
|
WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP
|
||
|
|
HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO
|
||
|
|
THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL
|
||
|
|
CLAIMS IN ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT
|
||
|
|
OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS
|
||
|
|
SOFTWARE.
|
||
|
|
*/
|
||
|
|
|
||
|
|
// Configuration bits: selected in the GUI
|
||
|
|
|
||
|
|
// CONFIG1
|
||
|
|
#pragma config FOSC = INTOSC // Oscillator Selection Bits->INTOSC oscillator: I/O function on CLKIN pin
|
||
|
|
#pragma config WDTE = OFF // Watchdog Timer Enable->WDT disabled
|
||
|
|
#pragma config PWRTE = OFF // Power-up Timer Enable->PWRT disabled
|
||
|
|
#pragma config MCLRE = ON // MCLR Pin Function Select->MCLR/VPP pin function is MCLR
|
||
|
|
#pragma config CP = OFF // Flash Program Memory Code Protection->Program memory code protection is disabled
|
||
|
|
#pragma config BOREN = ON // Brown-out Reset Enable->Brown-out Reset enabled
|
||
|
|
#pragma config CLKOUTEN = OFF // Clock Out Enable->CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin
|
||
|
|
#pragma config IESO = ON // Internal/External Switchover Mode->Internal/External Switchover Mode is enabled
|
||
|
|
#pragma config FCMEN = ON // Fail-Safe Clock Monitor Enable->Fail-Safe Clock Monitor is enabled
|
||
|
|
|
||
|
|
// CONFIG2
|
||
|
|
#pragma config WRT = OFF // Flash Memory Self-Write Protection->Write protection off
|
||
|
|
#pragma config PPS1WAY = ON // Peripheral Pin Select one-way control->The PPSLOCK bit cannot be cleared once it is set by software
|
||
|
|
#pragma config ZCD = OFF // Zero-cross detect disable->Zero-cross detect circuit is disabled at POR
|
||
|
|
#pragma config PLLEN = OFF // Phase Lock Loop enable->4x PLL is enabled when software sets the SPLLEN bit
|
||
|
|
#pragma config STVREN = ON // Stack Overflow/Underflow Reset Enable->Stack Overflow or Underflow will cause a Reset
|
||
|
|
#pragma config BORV = LO // Brown-out Reset Voltage Selection->Brown-out Reset Voltage (Vbor), low trip point selected.
|
||
|
|
#pragma config LPBOR = OFF // Low-Power Brown Out Reset->Low-Power BOR is disabled
|
||
|
|
#pragma config LVP = ON // Low-Voltage Programming Enable->Low-voltage programming enabled
|