Do not search for pads if the signal source for the PLL is something
other than the IO pin - these are guaranteed to already be placed and
have a bound Bel.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
If the CLKIN input of the PLL is connected to a special pin, then it
makes sense to try to place the PLL so that it uses a direct implicit
non-switched connection to this pin.
The transfer of information about pins for various purposes has been
implemented (clock input signal, feedback, etc), but so far only CLKIN
is used.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
For the following primitives:
- PADD9
- PADD18
- MULT9X9
- MULT18X18
- MULT36X36
- MULTALU18X18
- MULTALU36X18
- MULTADDALU18X18
- ALU54D
packing and processing of fixed wires between macro and between DSP
blocks is implemented.
Clusters of DSP and macro blocks are processed using custom placement of
cluster elements.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
Corrects the situation when it is impossible to use IOBUF with two
IOLOGIC elements at the same time - input and output.
Addresses https://github.com/YosysHQ/nextpnr/issues/1275
This is done by dividing one IOLOGIC Bel into two - input IOLOGIC and
output IOLOGIC plus checking for compatibility of the cells located
there.
At the moment, this check is simple and allows only the combination of
DDR and DDRC primitives.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
A small improvement - do not waste time analyzing already processed
networks in the previous step (and possibly steps).
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
Semi-dual port BSRAM (in Gowin terminology) has the same feature as
Single Port - the CE and OCE signals must be synchronized.
Such a sin has not yet been noticed for Dual Port.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
* Don't stop at the first bad "arc", but use the global network to the
maximum.
* Report partial/full use of global wires for the network.
* In case of complete routing failure, releasing the source - this is
actually a BUGFIX.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
This type setting is not needed here - the packer distinguishes memory
features by the X9 attribute, which will be correct anyway.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
The OCE signal in the SP(X)9B primitive is intended to control the
built-in output register. The documentation states that this port is
invalid when READ_MODE=0 is used. However, it has been experimentally
established that you cannot simply apply VCC or GND to it and forget it
- the discrepancy between the signal on this port and the signal on the
CE port leads to both skipping data reading and unnecessary reading
after CE has switched to 0.
Here we force these ports to be connected to the network, except in the
case where the user controls the OCE signal using non-constant signals.
Also:
* All PIPs for clock spines are made inaccessible to the common router
- in general, using these routes for signals that have not been
processed by a special globals router is fraught with effects that
are difficult to detect.
* The INV primitive has been added purely to speed up development -
this primitive is not generated by Yosys, but is almost always
present in vendor output files.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
The following primitives are implemented for the GW1NZ-1 chip:
* pROM - read only memory - (bitwidth: 1, 2, 4, 8, 16, 32).
* pROMX9 - read only memory - (bitwidth: 9, 18, 36).
* SDPB - semidual port - (bitwidth: 1, 2, 4, 8, 16, 32).
* SDPX9B - semidual port - (bitwidth: 9, 18, 36).
* DPB - dual port - (bitwidth: 16).
* DPX9B - dual port - (bitwidth: 18).
* SP - single port - (bitwidth: 1, 2, 4, 8, 16, 32).
* SPX9 - single port - (bitwidth: 9, 18, 36).
Also:
- The creation of databases for GW1NS-2 has been removed - this was not
planned to be supported in Himbaechel from the very beginning and
even examples were not created in apicula for this chip due to the
lack of boards with it on sale.
- It is temporarily prohibited to connect DFFs and LUTs into clusters
because for some reason this prevents the creation of images on lower
chips (placer cannot find the placement), although without these
clusters the images are quite working. Requires further research.
- Added creation of ALU with mode 0 - addition. Such an element is not
generated by Yosys, but it is a favorite vendor element and its
support here greatly simplifies the compilation of vendor netlists.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
Now the clock router can place a buffer into the specified network,
which divides the network into two parts: from the source to the buffer,
routing occurs through any available PIPs, and after the buffer to the
sink, only through a dedicated global clock network.
This is made specifically for the Tangnano20k where the external
oscillator is soldered to a regular non-clock pin. But it can be used
for other purposes, you just need to remember that the recipient must be
a CLK input or output pin.
The port/network to set the buffer to is specified in the .CST file:
CLOCK_LOC "name" BUFG;
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
Slightly change the Gowin device selection mechanism for database generation.
By default, nothing is generated as before.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
In these chips, the midline IOs are still simple, but are no longer just
IOBUF - that is, unlike the GW1N-1 IBUF and OBUF are not obtained by
applying a signal to the OEN input.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
And also fix the clock router to allow (with a warning) non-dedicated
routing in case of false detection of clock wires.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
Information about what function (main or auxiliary) the cell performs in
these primitives is transmitted through the tile's extra data. And this
also allows us to remove the calculation of the coordinates of the
auxiliary cell on the go.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
A single mechanism for creating a new type of tile if special functions
are found in the chip database that depend on the coordinates of the
tile.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
- experiment with notifyBelChange as an auxiliary cells reservation mechanism;
- since HCLK pips depend on the coordinates, and not on the tile type,
the tile type is copied if necessary;
- information about supported types of differential IO primitives has
been added to the extra information of the chip;
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
Add processing IO located on the sides of some chips. These are IOBUF,
which are converted into IBUF and OBUF not by fuses, but by signaling to
OE.
Also added the creation of a Global Set / Reset for all chips, instead
of a list of tile types, information from the apicula database is used,
and minor fixes.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
To implement unusual IOs that have a dynamically changing configuration
it is convenient to store the switching method in the additional chip
data.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
- The global router is modified to work out the routing of PLL outputs and inputs;
- Added API function to change wire type after its creation - there was
a need to unify all wires included in the node at the stage of node
creation, when all wires have already been created.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
- minor fixes for pinout saving;
- CST parser taken from generic-based apicula;
- $nextpnr IOB detachment is copied here because it is necessary to copy
attributes from deleted bels.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
Shamelessly adapted gatecat's router.
Very early version, not yet puzzled with recognizing clock sources and
controlling the type of wires involved.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
- RAM16SDP1, RAM16SDP2 and RAM16SDP4 support;
- Reading in these primitives is asynchronous, but we have taken
measures so that DFF Bels remain unoccupied and they can be used
to implement synchronous reading.
- misc fixes.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
- Added support for ALU running in "2" ADDSUB mode, the mode that yosys generates for gowin;
- Supports specifying an arbitrary input carry as well as passing the output carry to logic;
- A small restructuring of the source files.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
- MUX2_LUT5, MUX2_LUT6, MUX2_LUT7 and MUX2_LUT8 support;
- storing a common class of files in extra_data;
- misc fixes.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
Himbaechel-gowin has learned how to place DFFs of all types by tracking
the compatibility of CLK, CE and LSR inputs, as well as placing mutually
compatible flip-flops in adjacent slices.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
- VSS and VCC sources in each cell are used;
- constant LUT inputs are disabled;
- putting the class declaration into a header file.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
- wires, nodes and whites are generated from bases - apicula;
- roting of SN and EW bidirectional wires is supported;
- supports "wrapping" the wires at the edges of the chip;
- LUT1-4 and two types of DFF(R) are supported;
- simple IO is supported.
Signed-off-by: YRabbit <rabbit@yrabbit.cyou>
