7922b3bfc4
This replaces the arch-specific DelayInfo structure with new DelayPair (min/max only) and DelayQuad (min/max for both rise and fall) structures that form part of common code. This further reduces the amount of arch-specific code; and also provides useful data structures for timing analysis which will need to delay with pairs/quads of delays as it is improved. While there may be a small performance cost to arches that didn't separate the rise/fall cases (arches that aren't currently separating the min/max cases just need to be fixed...) in DelayInfo, my expectation is that inlining will mean this doesn't make much difference. Signed-off-by: gatecat <gatecat@ds0.me> |
||
|---|---|---|
| .. | ||
| examples | ||
| .gitignore | ||
| arch_pybindings.cc | ||
| arch_pybindings.h | ||
| arch.cc | ||
| arch.h | ||
| archdefs.h | ||
| bitstream.cc | ||
| bitstream.h | ||
| cells.cc | ||
| cells.h | ||
| CMakeLists.txt | ||
| config.cc | ||
| config.h | ||
| constids.inc | ||
| facade_import.py | ||
| family.cmake | ||
| main.cc | ||
| pack.cc | ||
| README.md | ||
nextpnr-machxo2
Experimental FOSS Place And Route backend for the Lattice MachXO2 family of
FPGAs. Fuzzing takes place as a subproject of prjtrellis.
Known to work:
- Basic routing from pads to SLICEs and back!
- Basic packing of one type of FF and LUT into half of a SLICE!
- Using the internal oscillator
OSCHas a clock LOGICSLICE mode
Things that probably work but are untested:
- Any non-3.3V I/O standard that doesn't use bank VREFs.
Things remaining to do include (but not limited to):
- More intelligent and efficient packing
- Global Routing (exists in database/sim models,
nextpnr-machxo2doesn't use it yet) - Secondary High Fanout Nets
- Edge Clocks (clock pads work, but not routed to global routing yet)
- PLLs
- Synchronous Release Global Set/Reset Interface (
SGSR) - Embedded Function Block (
EFB) - All DDR-related functionality
- Bank VREFs
- Embedded Block RAM (
EBR) CCU2andDPRAMSLICE modes
Quick Start
The following commands are known to work on a near-fresh Linux Mint system (thank you securelyfitz!):
Prerequisites
sudo apt install cmake clang-format libboost-all-dev build-essential
qt5-default libeigen3-dev build-essential clang bison flex libreadline-dev
gawk tcl-dev libffi-dev git graphviz xdot pkg-config python3
libboost-system-dev libboost-python-dev libboost-filesystem-dev zlib1g-dev
python3-setuptools python3-serial
Installation
Use an empty directory to hold all the cloned repositories. Upstream repos
can be used as well (e.g. YosysHQ/prjtrellis,
etc.).
git clone git@github.com:cr1901/prjtrellis.git
cd prjtrellis
git checkout facade
git submodule update --init --recursive
cd libtrellis
cmake -DCMAKE_INSTALL_PREFIX=/usr
make -j 8
sudo make install
cd ../../
git clone git@github.com:cr1901/yosys.git
cd yosys/
git checkout machxo2
make config-gcc
make
sudo make install
cd ../
git clone git@github.com:tinyfpga/TinyFPGA-A-Programmer.git
cd TinyFPGA-A-Programmer/
sudo python setup.py install
cd ../
git clone git@github.com:cr1901/nextpnr.git
cd nextpnr
git checkout machxo2
git submodule update --init --recursive
cmake . -DARCH=machxo2 -DBUILD_GUI=OFF -DTRELLIS_INSTALL_PREFIX=/usr -DBUILD_PYTHON=OFF -DBUILD_HEAP=OFF
make
Although uncommon, the facade and machxo2 branches of the above repos are
occassionally rebased; use git pull -f if necessary.
Demo
If you have a TinyFPGA Ax2 board with the TinyFPGA Programmer, the following script will build a blinky bitstream and load it onto the MachXO2; the gateware will flash the LED!
cd machxo2/examples/
sh demo.sh tinyfpga
The tinyfpga.v code used in demo.sh is slightly modified from the
user's guide to accommodate
(* LOC = "pin" *) constraints and the built-in user LED.