HardwareDriver/nuvoton/m451/steppernew/ssd1306.c

//
// LCD Driver: 0.96" OLED
//
// Interface: I2C
// pin1: Gnd
// pin2: Vcc
// pin3: SCL
// pin4: SDA
// pin5: OUT
// pin6: IN
// pin7: SCK
// pin8: CS

#include <stdio.h>
#include <stdint.h>
#include <string.h>
#include <M451Series.h>
#include "sys.h"
#include "gpio.h"
#include "i2c.h"
#include "ssd1306.h"
#include "codetab.h"

void OLED_SingleWrite(unsigned char index, unsigned char data)
{
        I2C_START(LCD_I2C_PORT);                         //Start
	      I2C_WAIT_READY(LCD_I2C_PORT);
        //LCD_I2C_PORT->INTSTS |= I2C_INTSTS_INTSTS_Msk;   //clear flag	
	
	      I2C_SET_DATA(LCD_I2C_PORT, LCD_I2C_SLA);         //send slave address
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI);
	      I2C_WAIT_READY(LCD_I2C_PORT);
        //LCD_I2C_PORT->INTSTS |= I2C_INTSTS_INTSTS_Msk;   //clear flag		

	      I2C_SET_DATA(LCD_I2C_PORT, index);               //send index
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI);
	      I2C_WAIT_READY(LCD_I2C_PORT);
        
				//LCD_I2C_PORT->INTSTS |= I2C_INTSTS_INTSTS_Msk;   //clear flag		

	      I2C_SET_DATA(LCD_I2C_PORT, data);                //send Data
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI);
	      I2C_WAIT_READY(LCD_I2C_PORT);
        //LCD_I2C_PORT->INTSTS |= I2C_INTSTS_INTSTS_Msk;   //clear flag		
				
				I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI|I2C_CTL_STO);//Stop
}

unsigned char OLED_SingleRead(unsigned char index)
{
				unsigned char tmp;
	      I2C_START(LCD_I2C_PORT);                         //Start
	      I2C_WAIT_READY(LCD_I2C_PORT);
        //LCD_I2C_PORT->INTSTS |= I2C_INTSTS_INTSTS_Msk;   //clear flag		
	
	      I2C_SET_DATA(LCD_I2C_PORT, LCD_I2C_SLA);         //send slave address+W
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI);
	      I2C_WAIT_READY(LCD_I2C_PORT);
        
	      I2C_SET_DATA(LCD_I2C_PORT, index);               //send index
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI);
	      I2C_WAIT_READY(LCD_I2C_PORT);
        
	
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_STA | I2C_CTL_SI);	//Start
	      I2C_WAIT_READY(LCD_I2C_PORT);
        

		    I2C_SET_DATA(LCD_I2C_PORT, (LCD_I2C_SLA+1));     //send slave address+R
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI);
	      I2C_WAIT_READY(LCD_I2C_PORT);
	
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI);
	      I2C_WAIT_READY(LCD_I2C_PORT);

				tmp = I2C_GET_DATA(LCD_I2C_PORT);                //read data   
	
	      I2C_SET_CONTROL_REG(LCD_I2C_PORT, I2C_CTL_SI|I2C_CTL_STO);//Stop
				return tmp;
}

void oledWriteCommand(unsigned char OLED_Command)
{
   OLED_SingleWrite(0x00, OLED_Command);
}

void oledWriteData(unsigned char OLED_Data)
{
   OLED_SingleWrite(0x40, OLED_Data);
}

void Init_LCD(void)
{
	oledWriteCommand(0xae); //display off
	oledWriteCommand(0x20);	//Set Memory Addressing Mode	
	oledWriteCommand(0x10);	//00,Horizontal Addressing Mode;01,Vertical Addressing Mode;10,Page Addressing Mode (RESET);11,Invalid
	oledWriteCommand(0xb0);	//Set Page Start Address for Page Addressing Mode,0-7
	oledWriteCommand(0xc8);	//Set COM Output Scan Direction
	oledWriteCommand(0x00);//---set low column address
	oledWriteCommand(0x10);//---set high column address
	oledWriteCommand(0x40);//--set start line address
	oledWriteCommand(0x81);//--set contrast control register
	oledWriteCommand(0x7f);
	oledWriteCommand(0xa1);//--set segment re-map 0 to 127
	oledWriteCommand(0xa6);//--set normal display
	oledWriteCommand(0xa8);//--set multiplex ratio(1 to 64)
	oledWriteCommand(0x3F);//
	oledWriteCommand(0xa4);//0xa4,Output follows RAM content;0xa5,Output ignores RAM content
	oledWriteCommand(0xd3);//-set display offset
	oledWriteCommand(0x00);//-not offset
	oledWriteCommand(0xd5);//--set display clock divide ratio/oscillator frequency
	oledWriteCommand(0xf0);//--set divide ratio
	oledWriteCommand(0xd9);//--set pre-charge period
	oledWriteCommand(0x22); //
	oledWriteCommand(0xda);//--set com pins hardware configuration
	oledWriteCommand(0x12);
	oledWriteCommand(0xdb);//--set vcomh
	oledWriteCommand(0x20);//0x20,0.77xVcc
	oledWriteCommand(0x8d);//--set DC-DC enable
	oledWriteCommand(0x14);//
	oledWriteCommand(0xaf);//--turn on oled panel 
}

void oled_address(unsigned char column, unsigned char page)
{
	oledWriteCommand(0xb0+page);                     // set page address
	oledWriteCommand(0x10 | ((column & 0xf0) >> 4)); // set column address MSB
	oledWriteCommand(0x00 |  (column & 0x0f)      ); // set column address LSB
}

void clear_LCD(void)
{
	int16_t x, Y;
	for (Y=0;Y<LCD_Ymax/8;Y++) 
	{
		oled_address(0, Y);
	  for (x=0;x<LCD_Xmax;x++)
	     oledWriteData(0x00);
	}
}

void draw_LCD(unsigned char *buffer)
{
	int16_t x, Y;
	for (Y=0;Y<8;Y++)
	{
	  oled_address(0, Y);
		for (x=0;x<LCD_Xmax;x++)
	     oledWriteData(buffer[x+Y*LCD_Xmax]);
	}
}

void print_C(unsigned char Col, unsigned char Line, char ascii)
{
	unsigned char j, i, tmp;	
	for (j=0;j<2;j++) {		
	    oled_address(Col*8, Line*2+j);
	    for (i=0;i<8;i++) {
	      tmp=F8X16[(ascii-0x20)*16+j*8+i];
	      oledWriteData(tmp);
		  }
  }
}

void print_Line(unsigned char Line, char Text[])
{
	unsigned char Col;
	  for (Col=0; Col<strlen(Text); Col++) 
			print_C(Col, Line, Text[Col]);
}