zcy
/
pluto_hdl_adi
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
pluto_hdl_adi/projects/dac_fmc_ebz/zc706/system_bd.tcl

25 lines
984 B
Tcl
Raw Normal View History

Add copyright and license to .tcl, .ttcl files Signed-off-by: Iulia Moldovan <Iulia.Moldovan@analog.com>
2023-07-06 12:08:22 +00:00
###############################################################################
## Copyright (C) 2019-2023 Analog Devices, Inc. All rights reserved.
### SPDX short identifier: ADIBSD
###############################################################################
dac_fmc_ebz: Add initial ZCU102 and ZC706 carrier support Add a generic project for the AD91xx-FMC-EBZ DAC boards connected to the ZCU102 and ZC706 carrier boards. The project is called dac_fmc_ebz as the intention is to support all DAC FMC evaluation boards with this project since they are sufficiently similar to be supported by the same design. This project will successively extended to add support for more boards. The desired DAC device and JESD operation mode must be selected from the following file: ./common/config.tcl This design can support the following FMC boards which are all pin compatible: * AD9135-FMC-EBZ * AD9136-FMC-EBZ * AD9144-FMC-EBZ * AD9152-FMC-EBZ * AD9154-FMC-EBZ * AD916x-FMC-EBZ * AD9171-FMC-EBZ * AD9172-FMC-EBZ * AD9173-FMC-EBZ Note that the AD9152-FMC-EBZ only uses the first 4 lanes, whereas all other boards use 8 lanes. This project assumes that the transceiver reference clock and SYSREF are provided via the clock distribution chip that is found on the ADxxxx-FMC-EBZ board. In terms of pin connections between the FPGA and the FMC board the AD9172-FMC-EBZ is very similar to the AD9144-FMC-EBZ. The main differences are: * The DAC txen signals are connected to different pins * The polarity of the spi_en signal is active low instead of active high * The maximum lane rate is up to 15.4 Gpbs To accommodate this 5 txctrl signals as well as the spi_en signal are connected to GPIOs. Software can decide how to use them depending on which FMC board is connected. Note that each carrier has a maximum supported lane rate. Modes of the AD9172 (and similar) that exceed the carrier specific limit can not be used on that carrier. The limits are as following: * ZC706: 10.3125 Gbps * ZCU102: 15.4 Gbps (max AD9172 lanerate) * SPI and GPIOs to PMOD header support Connect a SPI interface and some GPIOs to the PL PMOD headers on the zcu102 and zc706 carriers. This is can be used to control additional external hardware like a clock chip or an analog front-end. This is especially useful on FMC boards that do not feature a clock generator chip. The pin out is: PMOD 1: SPI clock PMOD 2: SPI chipselect PMOD 3: SPI MOSI PMOD 4: SPI MISO PMOD 7: GPIO 0 PMOD 8: GPIO 1 PMOD 9: GPIO 2 PMOD 10: GPIO 3 The GPIOs are mapped at offset 48-51 of the EMIO GPIOs.
2018-06-15 11:50:34 +00:00
set dac_fifo_address_width 14
source $ad_hdl_dir/projects/common/zc706/zc706_system_bd.tcl
source $ad_hdl_dir/projects/common/xilinx/dacfifo_bd.tcl
source ../common/dac_fmc_ebz_bd.tcl
sysid: Upgrade framework, header/ip are now at 2/1.1.a Unify tcl scripts; rename adi_pd_intel.tcl to adi_pd.tcl add git branch to internal use area; update log prints; update xilixn projects; fix cn0506 sysid script;
2020-10-09 14:28:10 +00:00
source $ad_hdl_dir/projects/scripts/adi_pd.tcl
dac_fmc_ebz: Add initial ZCU102 and ZC706 carrier support Add a generic project for the AD91xx-FMC-EBZ DAC boards connected to the ZCU102 and ZC706 carrier boards. The project is called dac_fmc_ebz as the intention is to support all DAC FMC evaluation boards with this project since they are sufficiently similar to be supported by the same design. This project will successively extended to add support for more boards. The desired DAC device and JESD operation mode must be selected from the following file: ./common/config.tcl This design can support the following FMC boards which are all pin compatible: * AD9135-FMC-EBZ * AD9136-FMC-EBZ * AD9144-FMC-EBZ * AD9152-FMC-EBZ * AD9154-FMC-EBZ * AD916x-FMC-EBZ * AD9171-FMC-EBZ * AD9172-FMC-EBZ * AD9173-FMC-EBZ Note that the AD9152-FMC-EBZ only uses the first 4 lanes, whereas all other boards use 8 lanes. This project assumes that the transceiver reference clock and SYSREF are provided via the clock distribution chip that is found on the ADxxxx-FMC-EBZ board. In terms of pin connections between the FPGA and the FMC board the AD9172-FMC-EBZ is very similar to the AD9144-FMC-EBZ. The main differences are: * The DAC txen signals are connected to different pins * The polarity of the spi_en signal is active low instead of active high * The maximum lane rate is up to 15.4 Gpbs To accommodate this 5 txctrl signals as well as the spi_en signal are connected to GPIOs. Software can decide how to use them depending on which FMC board is connected. Note that each carrier has a maximum supported lane rate. Modes of the AD9172 (and similar) that exceed the carrier specific limit can not be used on that carrier. The limits are as following: * ZC706: 10.3125 Gbps * ZCU102: 15.4 Gbps (max AD9172 lanerate) * SPI and GPIOs to PMOD header support Connect a SPI interface and some GPIOs to the PL PMOD headers on the zcu102 and zc706 carriers. This is can be used to control additional external hardware like a clock chip or an analog front-end. This is especially useful on FMC boards that do not feature a clock generator chip. The pin out is: PMOD 1: SPI clock PMOD 2: SPI chipselect PMOD 3: SPI MOSI PMOD 4: SPI MISO PMOD 7: GPIO 0 PMOD 8: GPIO 1 PMOD 9: GPIO 2 PMOD 10: GPIO 3 The GPIOs are mapped at offset 48-51 of the EMIO GPIOs.
2018-06-15 11:50:34 +00:00
Updated the makefiles to build the projects in subdirectories based on the build parameters. Running 'make' will build the default project directly in the project folder (like it did before) Running 'make RX_LANE_RATE=15 TX_LANE_RATE=15' will build the project inside the 'RXRATE15_TXRATE15' subdirectory. Running 'make CFG=cfg/test_config.txt" will use the variables found inside the configuration file and build the project inside the 'test_config' subdirectory. Running 'make clean' will clean the default project only. Running 'make CFG=cfg/test_config.txt clean' will clean the 'testconfig' build. Running 'make clean-all' will delete all the built configurations and libraries. Note that the 'JESD' and 'LANE' words from the parameter names are stripped. Signed-off-by: Bogdan Luncan <bogdan.luncan@analog.com>
2022-09-23 09:28:22 +00:00
set mem_init_sys_path [get_env_param ADI_PROJECT_DIR ""]mem_init_sys.txt;
system_id: deployed ip
2019-06-28 08:41:21 +00:00
#system ID
ad_ip_parameter axi_sysid_0 CONFIG.ROM_ADDR_BITS 9
Updated the makefiles to build the projects in subdirectories based on the build parameters. Running 'make' will build the default project directly in the project folder (like it did before) Running 'make RX_LANE_RATE=15 TX_LANE_RATE=15' will build the project inside the 'RXRATE15_TXRATE15' subdirectory. Running 'make CFG=cfg/test_config.txt" will use the variables found inside the configuration file and build the project inside the 'test_config' subdirectory. Running 'make clean' will clean the default project only. Running 'make CFG=cfg/test_config.txt clean' will clean the 'testconfig' build. Running 'make clean-all' will delete all the built configurations and libraries. Note that the 'JESD' and 'LANE' words from the parameter names are stripped. Signed-off-by: Bogdan Luncan <bogdan.luncan@analog.com>
2022-09-23 09:28:22 +00:00
ad_ip_parameter rom_sys_0 CONFIG.PATH_TO_FILE "[pwd]/$mem_init_sys_path"
system_id: deployed ip
2019-06-28 08:41:21 +00:00
ad_ip_parameter rom_sys_0 CONFIG.ROM_ADDR_BITS 9
dac_fmc_ebz: Add project info to sys_id Add project device and mode info to sys_id custom string
2019-10-10 13:05:47 +00:00
set ADI_DAC_DEVICE $::env(ADI_DAC_DEVICE)
set ADI_DAC_MODE $::env(ADI_DAC_MODE)
set sys_cstring "$ADI_DAC_DEVICE - $ADI_DAC_MODE"
system_id: deployed ip
2019-06-28 08:41:21 +00:00
sysid_gen_sys_init_file $sys_cstring
dac_fmc_ebz: Add initial ZCU102 and ZC706 carrier support Add a generic project for the AD91xx-FMC-EBZ DAC boards connected to the ZCU102 and ZC706 carrier boards. The project is called dac_fmc_ebz as the intention is to support all DAC FMC evaluation boards with this project since they are sufficiently similar to be supported by the same design. This project will successively extended to add support for more boards. The desired DAC device and JESD operation mode must be selected from the following file: ./common/config.tcl This design can support the following FMC boards which are all pin compatible: * AD9135-FMC-EBZ * AD9136-FMC-EBZ * AD9144-FMC-EBZ * AD9152-FMC-EBZ * AD9154-FMC-EBZ * AD916x-FMC-EBZ * AD9171-FMC-EBZ * AD9172-FMC-EBZ * AD9173-FMC-EBZ Note that the AD9152-FMC-EBZ only uses the first 4 lanes, whereas all other boards use 8 lanes. This project assumes that the transceiver reference clock and SYSREF are provided via the clock distribution chip that is found on the ADxxxx-FMC-EBZ board. In terms of pin connections between the FPGA and the FMC board the AD9172-FMC-EBZ is very similar to the AD9144-FMC-EBZ. The main differences are: * The DAC txen signals are connected to different pins * The polarity of the spi_en signal is active low instead of active high * The maximum lane rate is up to 15.4 Gpbs To accommodate this 5 txctrl signals as well as the spi_en signal are connected to GPIOs. Software can decide how to use them depending on which FMC board is connected. Note that each carrier has a maximum supported lane rate. Modes of the AD9172 (and similar) that exceed the carrier specific limit can not be used on that carrier. The limits are as following: * ZC706: 10.3125 Gbps * ZCU102: 15.4 Gbps (max AD9172 lanerate) * SPI and GPIOs to PMOD header support Connect a SPI interface and some GPIOs to the PL PMOD headers on the zcu102 and zc706 carriers. This is can be used to control additional external hardware like a clock chip or an analog front-end. This is especially useful on FMC boards that do not feature a clock generator chip. The pin out is: PMOD 1: SPI clock PMOD 2: SPI chipselect PMOD 3: SPI MOSI PMOD 4: SPI MISO PMOD 7: GPIO 0 PMOD 8: GPIO 1 PMOD 9: GPIO 2 PMOD 10: GPIO 3 The GPIOs are mapped at offset 48-51 of the EMIO GPIOs.
2018-06-15 11:50:34 +00:00
ad_ip_parameter dac_jesd204_link/tx CONFIG.SYSREF_IOB false