pluto_hdl_adi/library/axi_ad9680/axi_ad9680.v

338 lines
9.4 KiB
Coq
Raw Normal View History

// ***************************************************************************
// ***************************************************************************
// Copyright 2011(c) Analog Devices, Inc.
//
// All rights reserved.
//
// Redistribution and use in source and binary forms, with or without modification,
// are permitted provided that the following conditions are met:
// - Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
// - Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in
// the documentation and/or other materials provided with the
// distribution.
// - Neither the name of Analog Devices, Inc. nor the names of its
// contributors may be used to endorse or promote products derived
// from this software without specific prior written permission.
// - The use of this software may or may not infringe the patent rights
// of one or more patent holders. This license does not release you
// from the requirement that you obtain separate licenses from these
// patent holders to use this software.
// - Use of the software either in source or binary form, must be run
// on or directly connected to an Analog Devices Inc. component.
//
// THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
// INCLUDING, BUT NOT LIMITED TO, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A
// PARTICULAR PURPOSE ARE DISCLAIMED.
//
// IN NO EVENT SHALL ANALOG DEVICES BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
// EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, INTELLECTUAL PROPERTY
// RIGHTS, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
// BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
// STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
// THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
// ***************************************************************************
// ***************************************************************************
`timescale 1ns/100ps
module axi_ad9680 (
// jesd interface
// rx_clk is (line-rate/40)
rx_clk,
2016-07-21 20:07:18 +00:00
rx_sof,
rx_valid,
rx_data,
rx_ready,
// dma interface
adc_clk,
adc_enable_0,
adc_valid_0,
adc_data_0,
adc_enable_1,
adc_valid_1,
adc_data_1,
adc_dovf,
adc_dunf,
// axi interface
s_axi_aclk,
s_axi_aresetn,
s_axi_awvalid,
s_axi_awaddr,
s_axi_awprot,
s_axi_awready,
s_axi_wvalid,
s_axi_wdata,
s_axi_wstrb,
s_axi_wready,
s_axi_bvalid,
s_axi_bresp,
s_axi_bready,
s_axi_arvalid,
s_axi_araddr,
s_axi_arprot,
s_axi_arready,
s_axi_rvalid,
s_axi_rresp,
s_axi_rdata,
s_axi_rready);
hdl/library: Update the IP parameters The following IP parameters were renamed: PCORE_ID --> ID PCORE_DEVTYPE --> DEVICE_TYPE PCORE_IODELAY_GROUP --> IO_DELAY_GROUP CH_DW --> CHANNEL_DATA_WIDTH CH_CNT --> NUM_OF_CHANNELS PCORE_BUFTYPE --> DEVICE_TYPE PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE CHID --> CHANNEL_ID PCORE_DEVICE_TYPE --> DEVICE_TYPE PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N PCORE_SERDES_DDR_N --> SERDES_DDR_N PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE DP_DISABLE --> DATAPATH_DISABLE PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE C_BIG_ENDIAN --> BIG_ENDIAN C_M_DATA_WIDTH --> MASTER_DATA_WIDTH C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH NUM_CHANNELS --> NUM_OF_CHANNELS CHANNELS --> NUM_OF_CHANNELS PCORE_4L_2L_N -->QUAD_OR_DUAL_N C_ADDRESS_WIDTH --> ADDRESS_WIDTH C_DATA_WIDTH --> DATA_WIDTH C_CLKS_ASYNC --> CLKS_ASYNC PCORE_QUAD_DUAL_N --> QUAD_DUAL_N NUM_CS --> NUM_OF_CS PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID PCORE_CLK0_DIV --> CLK0_DIV PCORE_CLK1_DIV --> CLK1_DIV PCORE_CLKIN_PERIOD --> CLKIN_PERIOD PCORE_VCO_DIV --> VCO_DIV PCORE_Cr_Cb_N --> CR_CB_N PCORE_VCO_MUL --> VCO_MUL PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH PCORE_ADDR_WIDTH --> ADDRESS_WIDTH DADATA_WIDTH --> DATA_WIDTH NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS DEBOUNCER_LEN --> DEBOUNCER_LENGTH ADDR_WIDTH --> ADDRESS_WIDTH C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED Cr_Cb_N --> CR_CB_N ADDATA_WIDTH --> ADC_DATA_WIDTH BUFTYPE --> DEVICE_TYPE NUM_BITS --> NUM_OF_BITS WIDTH_A --> A_DATA_WIDTH WIDTH_B --> B_DATA_WIDTH CH_OCNT --> NUM_OF_CHANNELS_O M_CNT --> NUM_OF_CHANNELS_M P_CNT --> NUM_OF_CHANNELS_P CH_ICNT --> NUM_OF_CHANNELS_I CH_MCNT --> NUM_OF_CHANNELS_M 4L_2L_N --> QUAD_OR_DUAL_N SPI_CLK_ASYNC --> ASYNC_SPI_CLK MMCM_BUFIO_N --> MMCM_OR_BUFIO_N SERDES_DDR_N --> SERDES_OR_DDR_N CLK_ASYNC --> ASYNC_CLK CLKS_ASYNC --> ASYNC_CLK SERDES --> SERDES_OR_DDR_N GTH_GTX_N --> GTH_OR_GTX_N IF_TYPE --> DDR_OR_SDR_N PARALLEL_WIDTH --> DATA_WIDTH ADD_SUB --> ADD_OR_SUB_N A_WIDTH --> A_DATA_WIDTH CONST_VALUE --> B_DATA_VALUE IO_BASEADDR --> BASE_ADDRESS IO_WIDTH --> DATA_WIDTH QUAD_DUAL_N --> QUAD_OR_DUAL_N AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH MODE_OF_ENABLE --> CONTROL_TYPE CONTROL_TYPE --> LEVEL_OR_PULSE_N IQSEL --> Q_OR_I_N MMCM --> MMCM_OR_BUFR_N
2015-08-19 11:11:47 +00:00
parameter ID = 0;
parameter DEVICE_TYPE = 0;
parameter IO_DELAY_GROUP = "adc_if_delay_group";
// jesd interface
// rx_clk is (line-rate/40)
input rx_clk;
2016-07-21 20:07:18 +00:00
input [ 3:0] rx_sof;
input rx_valid;
input [127:0] rx_data;
output rx_ready;
// dma interface
output adc_clk;
output adc_enable_0;
output adc_valid_0;
output [63:0] adc_data_0;
output adc_enable_1;
output adc_valid_1;
output [63:0] adc_data_1;
input adc_dovf;
input adc_dunf;
// axi interface
input s_axi_aclk;
input s_axi_aresetn;
input s_axi_awvalid;
input [31:0] s_axi_awaddr;
input [ 2:0] s_axi_awprot;
output s_axi_awready;
input s_axi_wvalid;
input [31:0] s_axi_wdata;
input [ 3:0] s_axi_wstrb;
output s_axi_wready;
output s_axi_bvalid;
output [ 1:0] s_axi_bresp;
input s_axi_bready;
input s_axi_arvalid;
input [31:0] s_axi_araddr;
input [ 2:0] s_axi_arprot;
output s_axi_arready;
output s_axi_rvalid;
output [ 1:0] s_axi_rresp;
output [31:0] s_axi_rdata;
input s_axi_rready;
// internal registers
reg up_status_pn_err = 'd0;
reg up_status_pn_oos = 'd0;
reg up_status_or = 'd0;
reg [31:0] up_rdata = 'd0;
reg up_rack = 'd0;
reg up_wack = 'd0;
// internal clocks & resets
wire adc_rst;
wire up_rstn;
wire up_clk;
// internal signals
wire [55:0] adc_data_a_s;
wire [55:0] adc_data_b_s;
wire adc_or_a_s;
wire adc_or_b_s;
wire adc_status_s;
wire [ 1:0] up_adc_pn_err_s;
wire [ 1:0] up_adc_pn_oos_s;
wire [ 1:0] up_adc_or_s;
wire [31:0] up_rdata_s[0:2];
wire up_rack_s[0:2];
wire up_wack_s[0:2];
wire up_wreq_s;
wire [13:0] up_waddr_s;
wire [31:0] up_wdata_s;
wire up_rreq_s;
wire [13:0] up_raddr_s;
// signal name changes
assign up_clk = s_axi_aclk;
assign up_rstn = s_axi_aresetn;
// defaults
assign adc_valid_0 = 1'b1;
assign adc_valid_1 = 1'b1;
assign rx_ready = 1'b1;
// processor read interface
always @(negedge up_rstn or posedge up_clk) begin
if (up_rstn == 0) begin
up_status_pn_err <= 'd0;
up_status_pn_oos <= 'd0;
up_status_or <= 'd0;
up_rdata <= 'd0;
up_rack <= 'd0;
up_wack <= 'd0;
end else begin
up_status_pn_err <= | up_adc_pn_err_s;
up_status_pn_oos <= | up_adc_pn_oos_s;
up_status_or <= | up_adc_or_s;
up_rdata <= up_rdata_s[0] | up_rdata_s[1] | up_rdata_s[2];
up_rack <= up_rack_s[0] | up_rack_s[1] | up_rack_s[2];
up_wack <= up_wack_s[0] | up_wack_s[1] | up_wack_s[2];
end
end
// main (device interface)
2016-07-21 20:07:18 +00:00
axi_ad9680_if #(.DEVICE_TYPE (DEVICE_TYPE)) i_if (
.rx_clk (rx_clk),
2016-07-21 20:07:18 +00:00
.rx_sof (rx_sof),
.rx_data (rx_data),
.adc_clk (adc_clk),
.adc_rst (adc_rst),
.adc_data_a (adc_data_a_s),
.adc_data_b (adc_data_b_s),
.adc_or_a (adc_or_a_s),
.adc_or_b (adc_or_b_s),
.adc_status (adc_status_s));
// channel
2016-01-19 10:49:45 +00:00
axi_ad9680_channel #(.CHANNEL_ID(0)) i_channel_0 (
.adc_clk (adc_clk),
.adc_rst (adc_rst),
.adc_data (adc_data_a_s),
.adc_or (adc_or_a_s),
.adc_dfmt_data (adc_data_0),
.adc_enable (adc_enable_0),
.up_adc_pn_err (up_adc_pn_err_s[0]),
.up_adc_pn_oos (up_adc_pn_oos_s[0]),
.up_adc_or (up_adc_or_s[0]),
.up_rstn (up_rstn),
.up_clk (up_clk),
.up_wreq (up_wreq_s),
.up_waddr (up_waddr_s),
.up_wdata (up_wdata_s),
.up_wack (up_wack_s[0]),
.up_rreq (up_rreq_s),
.up_raddr (up_raddr_s),
.up_rdata (up_rdata_s[0]),
.up_rack (up_rack_s[0]));
// channel
2016-01-19 10:49:45 +00:00
axi_ad9680_channel #(.CHANNEL_ID(1)) i_channel_1 (
.adc_clk (adc_clk),
.adc_rst (adc_rst),
.adc_data (adc_data_b_s),
.adc_or (adc_or_b_s),
.adc_dfmt_data (adc_data_1),
.adc_enable (adc_enable_1),
.up_adc_pn_err (up_adc_pn_err_s[1]),
.up_adc_pn_oos (up_adc_pn_oos_s[1]),
.up_adc_or (up_adc_or_s[1]),
.up_rstn (up_rstn),
.up_clk (up_clk),
.up_wreq (up_wreq_s),
.up_waddr (up_waddr_s),
.up_wdata (up_wdata_s),
.up_wack (up_wack_s[1]),
.up_rreq (up_rreq_s),
.up_raddr (up_raddr_s),
.up_rdata (up_rdata_s[1]),
.up_rack (up_rack_s[1]));
// common processor control
hdl/library: Update the IP parameters The following IP parameters were renamed: PCORE_ID --> ID PCORE_DEVTYPE --> DEVICE_TYPE PCORE_IODELAY_GROUP --> IO_DELAY_GROUP CH_DW --> CHANNEL_DATA_WIDTH CH_CNT --> NUM_OF_CHANNELS PCORE_BUFTYPE --> DEVICE_TYPE PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE CHID --> CHANNEL_ID PCORE_DEVICE_TYPE --> DEVICE_TYPE PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N PCORE_SERDES_DDR_N --> SERDES_DDR_N PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE DP_DISABLE --> DATAPATH_DISABLE PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE C_BIG_ENDIAN --> BIG_ENDIAN C_M_DATA_WIDTH --> MASTER_DATA_WIDTH C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH NUM_CHANNELS --> NUM_OF_CHANNELS CHANNELS --> NUM_OF_CHANNELS PCORE_4L_2L_N -->QUAD_OR_DUAL_N C_ADDRESS_WIDTH --> ADDRESS_WIDTH C_DATA_WIDTH --> DATA_WIDTH C_CLKS_ASYNC --> CLKS_ASYNC PCORE_QUAD_DUAL_N --> QUAD_DUAL_N NUM_CS --> NUM_OF_CS PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID PCORE_CLK0_DIV --> CLK0_DIV PCORE_CLK1_DIV --> CLK1_DIV PCORE_CLKIN_PERIOD --> CLKIN_PERIOD PCORE_VCO_DIV --> VCO_DIV PCORE_Cr_Cb_N --> CR_CB_N PCORE_VCO_MUL --> VCO_MUL PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH PCORE_ADDR_WIDTH --> ADDRESS_WIDTH DADATA_WIDTH --> DATA_WIDTH NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS DEBOUNCER_LEN --> DEBOUNCER_LENGTH ADDR_WIDTH --> ADDRESS_WIDTH C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED Cr_Cb_N --> CR_CB_N ADDATA_WIDTH --> ADC_DATA_WIDTH BUFTYPE --> DEVICE_TYPE NUM_BITS --> NUM_OF_BITS WIDTH_A --> A_DATA_WIDTH WIDTH_B --> B_DATA_WIDTH CH_OCNT --> NUM_OF_CHANNELS_O M_CNT --> NUM_OF_CHANNELS_M P_CNT --> NUM_OF_CHANNELS_P CH_ICNT --> NUM_OF_CHANNELS_I CH_MCNT --> NUM_OF_CHANNELS_M 4L_2L_N --> QUAD_OR_DUAL_N SPI_CLK_ASYNC --> ASYNC_SPI_CLK MMCM_BUFIO_N --> MMCM_OR_BUFIO_N SERDES_DDR_N --> SERDES_OR_DDR_N CLK_ASYNC --> ASYNC_CLK CLKS_ASYNC --> ASYNC_CLK SERDES --> SERDES_OR_DDR_N GTH_GTX_N --> GTH_OR_GTX_N IF_TYPE --> DDR_OR_SDR_N PARALLEL_WIDTH --> DATA_WIDTH ADD_SUB --> ADD_OR_SUB_N A_WIDTH --> A_DATA_WIDTH CONST_VALUE --> B_DATA_VALUE IO_BASEADDR --> BASE_ADDRESS IO_WIDTH --> DATA_WIDTH QUAD_DUAL_N --> QUAD_OR_DUAL_N AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH MODE_OF_ENABLE --> CONTROL_TYPE CONTROL_TYPE --> LEVEL_OR_PULSE_N IQSEL --> Q_OR_I_N MMCM --> MMCM_OR_BUFR_N
2015-08-19 11:11:47 +00:00
up_adc_common #(.ID(ID)) i_up_adc_common (
.mmcm_rst (),
.adc_clk (adc_clk),
.adc_rst (adc_rst),
.adc_r1_mode (),
.adc_ddr_edgesel (),
.adc_pin_mode (),
.adc_status (adc_status_s),
.adc_sync_status (1'd0),
.adc_status_ovf (adc_dovf),
.adc_status_unf (adc_dunf),
.adc_clk_ratio (32'd4),
.adc_start_code (),
.adc_sync (),
.up_status_pn_err (up_status_pn_err),
.up_status_pn_oos (up_status_pn_oos),
.up_status_or (up_status_or),
.up_drp_sel (),
.up_drp_wr (),
.up_drp_addr (),
.up_drp_wdata (),
.up_drp_rdata (16'd0),
.up_drp_ready (1'd0),
.up_drp_locked (1'd1),
.up_usr_chanmax (),
.adc_usr_chanmax (8'd1),
.up_adc_gpio_in (32'd0),
.up_adc_gpio_out (),
.up_rstn (up_rstn),
.up_clk (up_clk),
.up_wreq (up_wreq_s),
.up_waddr (up_waddr_s),
.up_wdata (up_wdata_s),
.up_wack (up_wack_s[2]),
.up_rreq (up_rreq_s),
.up_raddr (up_raddr_s),
.up_rdata (up_rdata_s[2]),
.up_rack (up_rack_s[2]));
// up bus interface
up_axi i_up_axi (
.up_rstn (up_rstn),
.up_clk (up_clk),
.up_axi_awvalid (s_axi_awvalid),
.up_axi_awaddr (s_axi_awaddr),
.up_axi_awready (s_axi_awready),
.up_axi_wvalid (s_axi_wvalid),
.up_axi_wdata (s_axi_wdata),
.up_axi_wstrb (s_axi_wstrb),
.up_axi_wready (s_axi_wready),
.up_axi_bvalid (s_axi_bvalid),
.up_axi_bresp (s_axi_bresp),
.up_axi_bready (s_axi_bready),
.up_axi_arvalid (s_axi_arvalid),
.up_axi_araddr (s_axi_araddr),
.up_axi_arready (s_axi_arready),
.up_axi_rvalid (s_axi_rvalid),
.up_axi_rresp (s_axi_rresp),
.up_axi_rdata (s_axi_rdata),
.up_axi_rready (s_axi_rready),
.up_wreq (up_wreq_s),
.up_waddr (up_waddr_s),
.up_wdata (up_wdata_s),
.up_wack (up_wack),
.up_rreq (up_rreq_s),
.up_raddr (up_raddr_s),
.up_rdata (up_rdata),
.up_rack (up_rack));
endmodule
// ***************************************************************************
// ***************************************************************************