pluto_hdl_adi/library/axi_dmac/dest_axi_stream.v

// ***************************************************************************
// ***************************************************************************
// Copyright 2013(c) Analog Devices, Inc.
//  Author: Lars-Peter Clausen <lars@metafoo.de>
// 
// All rights reserved.
// 
// Redistribution and use in source and binary forms, with or without modification,
// are permitted provided that the following conditions are met:
//     - Redistributions of source code must retain the above copyright
//       notice, this list of conditions and the following disclaimer.
//     - Redistributions in binary form must reproduce the above copyright
//       notice, this list of conditions and the following disclaimer in
//       the documentation and/or other materials provided with the
//       distribution.
//     - Neither the name of Analog Devices, Inc. nor the names of its
//       contributors may be used to endorse or promote products derived
//       from this software without specific prior written permission.
//     - The use of this software may or may not infringe the patent rights
//       of one or more patent holders.  This license does not release you
//       from the requirement that you obtain separate licenses from these
//       patent holders to use this software.
//     - Use of the software either in source or binary form, must be run
//       on or directly connected to an Analog Devices Inc. component.
//    
// THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
// INCLUDING, BUT NOT LIMITED TO, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A
// PARTICULAR PURPOSE ARE DISCLAIMED.
//
// IN NO EVENT SHALL ANALOG DEVICES BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
// EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, INTELLECTUAL PROPERTY
// RIGHTS, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR 
// BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
// STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF 
// THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
// ***************************************************************************
// ***************************************************************************

module dmac_dest_axi_stream (
  input s_axis_aclk,
  input s_axis_aresetn,

  input enable,
  output enabled,
  input sync_id,
  output sync_id_ret,
        output xfer_req,

  input [ID_WIDTH-1:0] request_id,
  output [ID_WIDTH-1:0] response_id,
  output [ID_WIDTH-1:0] data_id,
  input data_eot,
  input response_eot,

  input m_axis_ready,
  output m_axis_valid,
  output [S_AXIS_DATA_WIDTH-1:0] m_axis_data,
        output m_axis_last,

  output fifo_ready,
  input fifo_valid,
  input [S_AXIS_DATA_WIDTH-1:0] fifo_data,

  input req_valid,
  output req_ready,
  input [BEATS_PER_BURST_WIDTH-1:0] req_last_burst_length,
        input req_xlast,

  output response_valid,
  input response_ready,
  output response_resp_eot,
  output [1:0] response_resp
);

parameter ID_WIDTH = 3;
parameter S_AXIS_DATA_WIDTH = 64;
parameter BEATS_PER_BURST_WIDTH = 4;

reg req_xlast_d = 1'b0;

assign sync_id_ret = sync_id;
wire data_enabled;
wire _fifo_ready;
wire m_axis_last_s;

// We are not allowed to just de-assert valid, but if the streaming target does
// not accept any samples anymore we'd lock up the DMA core. So retain the last
// beat when disabled until it is accepted. But if in the meantime the DMA core
// is re-enabled and new data becomes available overwrite the old.

always @(posedge s_axis_aclk) begin
  if(req_ready == 1'b1) begin
    req_xlast_d <= req_xlast;
  end
end

assign m_axis_last = (req_xlast_d == 1'b1) ? m_axis_last_s : 1'b0;

dmac_data_mover # (
  .ID_WIDTH(ID_WIDTH),
  .DATA_WIDTH(S_AXIS_DATA_WIDTH),
  .BEATS_PER_BURST_WIDTH(BEATS_PER_BURST_WIDTH),
  .DISABLE_WAIT_FOR_ID(0),
  .LAST(1)
) i_data_mover (
  .clk(s_axis_aclk),
  .resetn(s_axis_aresetn),

  .enable(enable),
  .enabled(data_enabled),
  .sync_id(sync_id),
        .xfer_req(xfer_req),

  .request_id(request_id),
  .response_id(data_id),
  .eot(data_eot),

  .req_valid(req_valid),
  .req_ready(req_ready),
  .req_last_burst_length(req_last_burst_length),

  .m_axi_ready(m_axis_ready),
  .m_axi_valid(m_axis_valid),
  .m_axi_data(m_axis_data),
        .m_axi_last(m_axis_last_s),
  .s_axi_ready(_fifo_ready),
  .s_axi_valid(fifo_valid),
  .s_axi_data(fifo_data)
);

dmac_response_generator # (
  .ID_WIDTH(ID_WIDTH)
) i_response_generator (
  .clk(s_axis_aclk),
  .resetn(s_axis_aresetn),

  .enable(data_enabled),
  .enabled(enabled),
  .sync_id(sync_id),

  .request_id(data_id),
  .response_id(response_id),

  .eot(response_eot),

  .resp_valid(response_valid),
  .resp_ready(response_ready),
  .resp_eot(response_resp_eot),
  .resp_resp(response_resp)
);

assign fifo_ready = _fifo_ready | ~enabled;

endmodule