ADD adaq42xx (#1209)

* ad4630_fmc: Initial version of ADAQ4224 w/ and w/o fully isolated power supply

Signed-off-by: Liviu Adace <liviu.adace@analog.com>

* docs:ad4630_fmc: Add documentation for ADAQ4224

Signed-off-by: Liviu Adace <liviu.adace@analog.com>

---------

Signed-off-by: Liviu Adace <liviu.adace@analog.com>

docs/projects/ad4630_fmc/index.rst

@@ -37,6 +37,13 @@ integrates all critical power supply and reference bypass capacitors, reducing
 the footprint and system component count, and lessening sensitivity to board
 layout.
 
+The ADAQ4224 is a μModule® precision data acquisition (DAQ) signal chain 
+solution that reduces the development cycle of a precision measurement system 
+by transferring the signal chain design challenge of component selection, 
+optimization, and layout from the designer to the device. With a guaranteed 
+maximum ±TBD ppm INL and no missing codes at 24 bits, the ADAQ4224 achieves
+unparalleled precision from −40°C to +85°C.
+
 The HDL reference design for the :adi:`EVAL-AD4630_FMCZ` and
 :adi:`EVAL-AD4030_FMCZ` provides all the interfaces that are necessary to
 interact with the device using a Xilinx FPGA development board. The design has
@@ -61,6 +68,8 @@ Supported boards
 -  :adi:`EVAL-AD4030-24FMCZ <EVAL-AD4030-24FMCZ>`
 -  :adi:`EVAL-AD4630-16FMCZ <EVAL-AD4630-16FMCZ>`
 -  :adi:`EVAL-AD4630-24FMCZ <EVAL-AD4630-24FMCZ>`
+-  EVAL-ADAQ4224-FMCZ <EVAL-ADAQ4224>
+-  EVAL-ISO-4224-FMCZ <EVAL-ISO-ADAQ4224>
 
 Supported devices
 -------------------------------------------------------------------------------
@@ -68,6 +77,7 @@ Supported devices
 -  :adi:`AD4030-24`
 -  :adi:`AD4630-16`
 -  :adi:`AD4630-24`
+-  ADAQ4224
 
 Supported carriers
 -------------------------------------------------------------------------------
@@ -121,6 +131,11 @@ where the two signals will have different frequencies.
    :align: center
    :alt: AD4630_FMC SPI mode - transfer zone 2 block diagram
 
+.. image:: adaq42xx_hdl_cm0_cz2_1.svg
+   :width: 800
+   :align: center
+   :alt: ADAQ4224_FMC SPI mode - transfer zone 2 block diagram
+
 Echo clock mode - transfer zone 2
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
@@ -135,6 +150,11 @@ mode.
    :align: center
    :alt: AD4630_FMC Echo clock mode - transfer zone 2 block diagram
 
+.. image:: adaq42xx_hdl_cm1_cz2_1.svg
+   :width: 800
+   :align: center
+   :alt: ADAQ4224_FMC Echo clock mode - transfer zone 2 block diagram
+
 The design supports the following interface and clock modes both in SDR and DDR:
 
 ================== ================== ================== ==================
@@ -176,8 +196,14 @@ spi_ad463x_axi_regmap     0x44A0_0000
 axi_ad463x_dma            0x44A3_0000
 spi_clkgen                0x44A7_0000
 cnv_generator             0x44B0_0000
+sync_generator*           0x44C0_0000
 ========================  ===========
 
+.. admonition:: Legend
+   :class: note
+
+   -   ``*`` instantiated, but only used for ADAQ4224 with isolated power supply 
+
 I2C connections
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 
@@ -195,11 +221,21 @@ I2C connections
      - axi_iic_fmc
      - 0x4162_0000
      - ---
-   * - PL
+   * - 
-     - iic_main
+     - 
-     - axi_iic_main
+     - 
-     - 0x4160_0000
+     - 0x50
-     - ---
+     - eeprom
+   * - 
+     - 
+     - 
+     - 0x5F
+     - temperature sensor  *
+
+.. admonition:: Legend
+   :class: note
+
+   -   ``*`` Temperature Sensor HW Monitor is present only in ADAQ4224
 
 SPI connections
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
@@ -240,7 +276,25 @@ The Software GPIO number is calculated as follows:
      - INOUT
      - 32
      - 86
-     
+   * - adaq42xx_pgia_mux[0]*
+     - INOUT
+     - 33
+     - 87
+   * - adaq42xx_pgia_mux[1]*
+     - INOUT
+     - 34
+     - 88
+   * - max17687_rst**
+     - INOUT
+     - 35
+     - 89
+
+.. admonition:: Legend
+   :class: note
+
+   -   ``*`` instantiated, but used for ADAQ4224 only
+   -   ``**`` instantiated, but used for ADAQ4224 with isolated power supply
+
 Interrupts
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 

docs/projects/index.rst

@@ -19,7 +19,7 @@ Contents
    :maxdepth: 1
 
    AD4134-FMC <ad4134_fmc/index>
-   AD4630-FMC <ad4630_fmc/index>
+   AD4630-FMC/AD4030-FMC/ADAQ4224-FMC <ad4630_fmc/index>
    AD469X-FMC <ad469x_fmc/index>
    AD5766-SDZ <ad5766_sdz/index>
    AD7134-FMC <ad7134_fmc/index>

projects/ad4630_fmc/common/ad4030_fmc.txt

@@ -0,0 +1,20 @@
+# ad4030
+
+FMC_pin   FMC_port       Schematic_name     System_top_name     IOSTANDARD  Termination
+
+G6        LA00_P_CC      SCK_FMC            ad463x_spi_sclk     LVCMOS25    #N/A
+G7        LA00_N_CC      CS_FMC             ad463x_spi_cs       LVCMOS25    #N/A
+G9        LA03_P         SDO2_FMC           ad463x_spi_sdi[2]   LVCMOS25    #N/A
+G10       LA03_N         SDO3_FMC           ad463x_spi_sdi[3]   LVCMOS25    #N/A
+H4        CLK0_M2C_P     CLK                ad463x_ext_clk      LVCMOS25    #N/A
+H7        LA02_P         SDO0_FMC           ad463x_spi_sdi[0]   LVCMOS25    #N/A
+H8        LA02_N         SDO1_FMC           ad463x_spi_sdi[1]   LVCMOS25    #N/A
+H10       LA04_P         SDO4_FMC           ad463x_spi_sdi[4]   LVCMOS25    #N/A
+H11       LA04_N         SDO5_FMC           ad463x_spi_sdi[5]   LVCMOS25    #N/A
+D8        LA01_P_CC      CNV_FMC            ad463x_cnv          LVCMOS25    #N/A
+D9        LA01_N_CC      RESET_FMC          ad463x_resetn       LVCMOS25    #N/A
+D11       LA05_P         SDO6_FMC           ad463x_spi_sdi[6]   LVCMOS25    #N/A
+D12       LA05_N         SDO7_FMC           ad463x_spi_sdi[7]   LVCMOS25    #N/A
+D20       LA17_P_CC      SCK_OUT_FMC        ad463x_echo_sclk    LVCMOS25    #N/A
+C11       LA06_N         SDI_FMC            ad463x_spi_sdo      LVCMOS25    #N/A
+C22       LA18_P_CC      BUSY_FMC           ad463x_busy         LVCMOS25    #N/A

projects/ad4630_fmc/common/ad463x_bd.tcl

@@ -21,6 +21,9 @@ set cnv_ref_clk 100
 # NOTE: this is a default value, software may or may not change this
 set adc_sampling_rate 1000000
 
+# specify the MAX17687 and LT8608 SYNC signal frequency (400KHz)
+set max17687_sync_freq 400000
+
 #create_bd_intf_port -mode Master -vlnv analog.com:interface:spi_engine_rtl:1.0 ad463x_spi
 
 create_bd_port -dir O ad463x_spi_sclk
@@ -34,6 +37,8 @@ create_bd_port -dir I ad463x_busy
 create_bd_port -dir O ad463x_cnv
 create_bd_port -dir I ad463x_ext_clk
 
+create_bd_port -dir O max17687_sync_clk
+
 ## To support the 2MSPS (SCLK == 80 MHz), set the spi clock to 160 MHz
 
 ad_ip_instance axi_clkgen spi_clkgen
@@ -70,6 +75,9 @@ ad_ip_parameter $hier_spi_engine/${hier_spi_engine}_axi_regmap CONFIG.CFG_INFO_3
 ## CNV generator; the actual sample rate will be PULSE_PERIOD * (1/cnv_ref_clk)
 set sampling_cycle [expr int(ceil(double($cnv_ref_clk * 1000000) / $adc_sampling_rate))]
 
+## setup the pulse period for the MAX17687 and LT8608 SYNC signal
+set max17687_cycle [expr int(ceil(double($cnv_ref_clk * 1000000) / $max17687_sync_freq))] 
+
 ad_ip_instance axi_pwm_gen cnv_generator
 ad_ip_parameter cnv_generator CONFIG.N_PWMS 2
 ad_ip_parameter cnv_generator CONFIG.PULSE_0_PERIOD $sampling_cycle
@@ -78,6 +86,11 @@ ad_ip_parameter cnv_generator CONFIG.PULSE_1_PERIOD $sampling_cycle
 ad_ip_parameter cnv_generator CONFIG.PULSE_1_WIDTH 1
 ad_ip_parameter cnv_generator CONFIG.PULSE_1_OFFSET 1
 
+ad_ip_instance axi_pwm_gen sync_generator
+ad_ip_parameter sync_generator CONFIG.N_PWMS 1
+ad_ip_parameter sync_generator CONFIG.PULSE_0_PERIOD $max17687_cycle
+ad_ip_parameter sync_generator CONFIG.PULSE_0_WIDTH [expr int(ceil(double($max17687_cycle) / 2))]
+
 ad_ip_instance spi_axis_reorder data_reorder
 ad_ip_parameter data_reorder CONFIG.NUM_OF_LANES $NUM_OF_SDI
 
@@ -171,15 +184,18 @@ if {$CAPTURE_ZONE == 1} {
 
 }
 ad_connect ad463x_cnv cnv_generator/pwm_1
+ad_connect max17687_sync_clk sync_generator/pwm_0
 
 # clocks
 
 ad_connect $sys_cpu_clk $hier_spi_engine/clk
 ad_connect $sys_cpu_clk cnv_generator/s_axi_aclk
+ad_connect $sys_cpu_clk sync_generator/s_axi_aclk
 ad_connect spi_clk $hier_spi_engine/spi_clk
 ad_connect spi_clk data_reorder/axis_aclk
 ad_connect spi_clk axi_ad463x_dma/s_axis_aclk
 ad_connect ad463x_ext_clk cnv_generator/ext_clk
+ad_connect ad463x_ext_clk sync_generator/ext_clk
 
 # resets
 
@@ -201,6 +217,7 @@ ad_connect  axi_ad463x_dma/s_axis data_reorder/m_axis
 
 ad_cpu_interconnect 0x44a00000 $hier_spi_engine/${hier_spi_engine}_axi_regmap
 ad_cpu_interconnect 0x44b00000 cnv_generator
+ad_cpu_interconnect 0x44c00000 sync_generator
 ad_cpu_interconnect 0x44a30000 axi_ad463x_dma
 ad_cpu_interconnect 0x44a70000 spi_clkgen
 

projects/ad4630_fmc/common/adaq42xx_fmc.txt

@@ -0,0 +1,27 @@
+# adaq42xx
+
+FMC_pin   FMC_port       Schematic_name     System_top_name     IOSTANDARD  Termination
+
+G6        LA00_P_CC      SCK_FMC            ad463x_spi_sclk     LVCMOS25    #N/A
+G7        LA00_N_CC      CS_FMC             ad463x_spi_cs       LVCMOS25    #N/A
+G9        LA03_P         SDO2_FMC           ad463x_spi_sdi[2]   LVCMOS25    #N/A
+G10       LA03_N         SDO3_FMC           ad463x_spi_sdi[3]   LVCMOS25    #N/A
+H4        CLK0_M2C_P     CLK                ad463x_ext_clk      LVCMOS25    #N/A
+H7        LA02_P         SDO0_FMC           ad463x_spi_sdi[0]   LVCMOS25    #N/A
+H8        LA02_N         SDO1_FMC           ad463x_spi_sdi[1]   LVCMOS25    #N/A
+H10       LA04_P         SDO4_FMC           ad463x_spi_sdi[4]   LVCMOS25    #N/A
+H11       LA04_N         SDO5_FMC           ad463x_spi_sdi[5]   LVCMOS25    #N/A
+D8        LA01_P_CC      CNV_FMC            ad463x_cnv          LVCMOS25    #N/A
+D9        LA01_N_CC      RESET_FMC          ad463x_resetn       LVCMOS25    #N/A
+D11       LA05_P         SDO6_FMC           ad463x_spi_sdi[6]   LVCMOS25    #N/A
+D12       LA05_N         SDO7_FMC           ad463x_spi_sdi[7]   LVCMOS25    #N/A
+D20       LA17_P_CC      SCK_OUT_FMC        ad463x_echo_sclk    LVCMOS25    #N/A
+C11       LA06_N         SDI_FMC            ad463x_spi_sdo      LVCMOS25    #N/A
+C22       LA18_P_CC      BUSY_FMC           ad463x_busy         LVCMOS25    #N/A
+
+G12       LA08_P         MUX_A0             adaq42xx_pgia_mux[0] LVCMOS25   #N/A
+G13       LA08_N         MUX_A1             adaq42xx_pgia_mux[1] LVCMOS25   #N/A
+
+H13       LA07_P         RST                max17687_rst        LVCMOS25    #N/A
+H14       LA07_N         EN                 max17687_en         LVCMOS25    #N/A
+D21       LA17_CC_N      SYNCFMC            max17687_sync_clk   LVCMOS25    #N/A

projects/ad4630_fmc/zed/README.md

@@ -3,8 +3,9 @@
 
 ## Building the design
 
-The design supports almost all the digital interface modes of AD4630-24, a new
+The design supports almost all the digital interface modes of AD463x, AD403x 
-bit stream should be generated each time when the targeted configuration changes.
+and adaq42xx a new bit stream should be generated each time when the targeted 
+configuration changes.
 
 Default configuration: generic SPI mode for clocking, 2 lanes per channel, SDR 
 data capture and capture zone 2. 
@@ -18,7 +19,16 @@ data capture and capture zone 2.
 |  CAPTURE_ZONE   |  1 - negedge of BUSY / 2 - next posedge of CNV    |
 |  DDR_EN         |  0 - MISO runs on SDR / 1 - MISO runs on DDR      |
 
-**Example:** make CLK_MODE=1 NUM_OF_SDI=2 CAPTURE_ZONE=2 DDR_EN=0
+**Example:** 
+  make CLK_MODE=0 NUM_OF_SDI=2 CAPTURE_ZONE=2 DDR_EN=0
+  make CLK_MODE=0 NUM_OF_SDI=4 CAPTURE_ZONE=2 DDR_EN=0
+  make CLK_MODE=0 NUM_OF_SDI=8 CAPTURE_ZONE=2 DDR_EN=0
+  make CLK_MODE=1 NUM_OF_SDI=2 CAPTURE_ZONE=2 DDR_EN=0
+  make CLK_MODE=1 NUM_OF_SDI=4 CAPTURE_ZONE=2 DDR_EN=0
+  make CLK_MODE=1 NUM_OF_SDI=8 CAPTURE_ZONE=2 DDR_EN=0
+  make CLK_MODE=1 NUM_OF_SDI=2 CAPTURE_ZONE=2 DDR_EN=1
+  make CLK_MODE=1 NUM_OF_SDI=4 CAPTURE_ZONE=2 DDR_EN=1
+  make CLK_MODE=1 NUM_OF_SDI=8 CAPTURE_ZONE=2 DDR_EN=1
 
 ## Documentation
 

projects/ad4630_fmc/zed/system_constr.xdc

@@ -1,5 +1,5 @@
 ###############################################################################
-## Copyright (C) 2021-2023 Analog Devices, Inc. All rights reserved.
+## Copyright (C) 2021-2024 Analog Devices, Inc. All rights reserved.
 ### SPDX short identifier: ADIBSD
 ###############################################################################
 
@@ -14,6 +14,13 @@ set_property -dict {PACKAGE_PIN D20 IOSTANDARD LVCMOS25} [get_ports ad463x_busy]
 set_property -dict {PACKAGE_PIN N19 IOSTANDARD LVCMOS25} [get_ports ad463x_cnv]                 ; ## D8  FMC_LA01_CC_P
 set_property -dict {PACKAGE_PIN L18 IOSTANDARD LVCMOS25} [get_ports ad463x_ext_clk]             ; ## H4  FMC_CLK0_P
 
+set_property -dict {PACKAGE_PIN J21 IOSTANDARD LVCMOS25} [get_ports {adaq42xx_pgia_mux[0]}]    ; ## G12  FMC-LA08_P
+set_property -dict {PACKAGE_PIN J22 IOSTANDARD LVCMOS25} [get_ports {adaq42xx_pgia_mux[1]}]    ; ## G13  FMC-LA08_N
+
+set_property -dict {PACKAGE_PIN T16 IOSTANDARD LVCMOS25} [get_ports max17687_rst]              ; ## H13  FMC-LA07_P
+set_property -dict {PACKAGE_PIN T17 IOSTANDARD LVCMOS25} [get_ports max17687_en]               ; ## H14  FMC-LA07_N
+set_property -dict {PACKAGE_PIN B20 IOSTANDARD LVCMOS25} [get_ports max17687_sync_clk]         ; ## D21  FMC-LA17_N_CC
+
 # external clock, that drives the CNV generator, must have a maximum 100 MHz frequency
 create_clock -period 10.000 -name cnv_ext_clk [get_ports ad463x_ext_clk]
 

projects/ad4630_fmc/zed/system_top.v

@@ -1,6 +1,6 @@
 // ***************************************************************************
 // ***************************************************************************
-// Copyright (C) 2021-2023 Analog Devices, Inc. All rights reserved.
+// Copyright (C) 2021-2024 Analog Devices, Inc. All rights reserved.
 //
 // In this HDL repository, there are many different and unique modules, consisting
 // of various HDL (Verilog or VHDL) components. The individual modules are
@@ -95,7 +95,13 @@ module system_top #(
   input           ad463x_ext_clk,
   output          ad463x_cnv,
   input           ad463x_busy,
-  inout           ad463x_resetn
+  inout           ad463x_resetn,
+
+  inout   [ 1:0]  adaq42xx_pgia_mux,
+
+  inout           max17687_rst,
+  output          max17687_en,
+  output          max17687_sync_clk
 );
 
   // internal signals
@@ -114,7 +120,8 @@ module system_top #(
 
   // instantiations
 
-  assign gpio_i[63:33] = 31'b0;
+  assign gpio_i[63:36] = 27'b0;
+  assign max17687_en = 1'b1;
 
   ad_data_clk #(
     .SINGLE_ENDED (1)
@@ -135,12 +142,14 @@ module system_top #(
     .clk (ad463x_echo_sclk_s));
 
   ad_iobuf #(
-    .DATA_WIDTH(1)
+    .DATA_WIDTH(4)
   ) i_ad463x_gpio_iobuf (
-    .dio_t(gpio_t[32]),
+    .dio_t(gpio_t[35:32]),
-    .dio_i(gpio_o[32]),
+    .dio_i(gpio_o[35:32]),
-    .dio_o(gpio_i[32]),
+    .dio_o(gpio_i[35:32]),
-    .dio_p(ad463x_resetn));
+    .dio_p ({max17687_rst,      // 35
+             adaq42xx_pgia_mux, // 34:33
+             ad463x_resetn}));  // 32
 
   ad_iobuf #(
     .DATA_WIDTH(32)
@@ -235,6 +244,7 @@ module system_top #(
     .ad463x_busy (ad463x_busy),
     .ad463x_cnv (ad463x_cnv),
     .ad463x_ext_clk (ext_clk_s),
+    .max17687_sync_clk (max17687_sync_clk),
     .otg_vbusoc (otg_vbusoc),
     .spdif (spdif));