c9a7d4d927
Add copyright and license to .tcl, .ttcl files
...
Signed-off-by: Iulia Moldovan <Iulia.Moldovan@analog.com>
2023-07-25 15:22:26 +03:00
6a016c62db
kc705 vc707: Increase linear flash capacity
2023-04-26 10:08:52 +03:00
0680e44330
system_id: deployed ip
2019-08-06 16:53:11 +03:00
de510b45ab
base: Add system_processor_rst for all the global clocks
2019-06-11 18:13:06 +03:00
20c714eccf
common: Define three global clock nets
...
For all the Xilinx base design, define three global clock nets, which
are saved in the following three global variable: $sys_cpu_clk, $sys_dma_clk
and $sys_iodelay_clk.
These clock nets are connected to different clock sources depending of
the FPGA architecture used on the carrier. In general the following
frequencies are used:
- sys_cpu_clk - 100MHz
- sys_dma_clk - 200MHz or 250Mhz
- sys_iodelay_clk - 200MHz or 500Mhz
2019-06-11 18:13:06 +03:00
ebae8bf8c1
Remove interrupts from system_top for all xilinx projects
...
- remove interrupts from system_top
- for all suported carriers:
- remove all interrupt bd pins
- connect to GND all initial unconnected interrupt pins
- update ad_cpu_interrupt procedure to disconnect a interrupt from GND
before connectiong it to another pin.
2018-08-10 10:10:58 +03:00
d65a543854
kc705: Fix ethernet address span
2017-06-30 14:23:01 +03:00
fa794520fd
kc705_common/adv7511: Update IP instantiations
2017-04-21 15:03:31 +03:00
73413366bc
daq2/all - warnings fix
2016-08-17 10:36:00 -04:00
0694a5015d
kc705- 2016.2 version
2016-08-16 12:54:39 -04:00
27f5f1dcbe
kc705: Updated common design to 2015.4
2016-03-15 15:17:53 +02:00
77e2eb7364
projects/common: Fix parameter name for xilinx core axi_gpio
...
Parameter C_GPDATA_WIDTH is changed to C_GPIO_WIDTH.
2015-08-25 10:07:11 +03:00
d3e090da3d
projects/common: Upgrade Xilinx's IP cores
...
To update the projects to Vivado 2015.2 the following IP cores were upgraded:
+ microblaze 9.4 to microblaze 9.5
+ axi_ethernet 6.2 to 7.0
+ mig 6.1 to 7.0
2015-08-25 10:03:49 +03:00
57cfb7cfb1
hdl/library: Update the IP parameters
...
The following IP parameters were renamed:
PCORE_ID --> ID
PCORE_DEVTYPE --> DEVICE_TYPE
PCORE_IODELAY_GROUP --> IO_DELAY_GROUP
CH_DW --> CHANNEL_DATA_WIDTH
CH_CNT --> NUM_OF_CHANNELS
PCORE_BUFTYPE --> DEVICE_TYPE
PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE
CHID --> CHANNEL_ID
PCORE_DEVICE_TYPE --> DEVICE_TYPE
PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N
PCORE_SERDES_DDR_N --> SERDES_DDR_N
PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE
DP_DISABLE --> DATAPATH_DISABLE
PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE
C_BIG_ENDIAN --> BIG_ENDIAN
C_M_DATA_WIDTH --> MASTER_DATA_WIDTH
C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH
NUM_CHANNELS --> NUM_OF_CHANNELS
CHANNELS --> NUM_OF_CHANNELS
PCORE_4L_2L_N -->QUAD_OR_DUAL_N
C_ADDRESS_WIDTH --> ADDRESS_WIDTH
C_DATA_WIDTH --> DATA_WIDTH
C_CLKS_ASYNC --> CLKS_ASYNC
PCORE_QUAD_DUAL_N --> QUAD_DUAL_N
NUM_CS --> NUM_OF_CS
PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID
PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID
PCORE_CLK0_DIV --> CLK0_DIV
PCORE_CLK1_DIV --> CLK1_DIV
PCORE_CLKIN_PERIOD --> CLKIN_PERIOD
PCORE_VCO_DIV --> VCO_DIV
PCORE_Cr_Cb_N --> CR_CB_N
PCORE_VCO_MUL --> VCO_MUL
PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC
PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH
PCORE_ADDR_WIDTH --> ADDRESS_WIDTH
DADATA_WIDTH --> DATA_WIDTH
NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS
DEBOUNCER_LEN --> DEBOUNCER_LENGTH
ADDR_WIDTH --> ADDRESS_WIDTH
C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED
Cr_Cb_N --> CR_CB_N
ADDATA_WIDTH --> ADC_DATA_WIDTH
BUFTYPE --> DEVICE_TYPE
NUM_BITS --> NUM_OF_BITS
WIDTH_A --> A_DATA_WIDTH
WIDTH_B --> B_DATA_WIDTH
CH_OCNT --> NUM_OF_CHANNELS_O
M_CNT --> NUM_OF_CHANNELS_M
P_CNT --> NUM_OF_CHANNELS_P
CH_ICNT --> NUM_OF_CHANNELS_I
CH_MCNT --> NUM_OF_CHANNELS_M
4L_2L_N --> QUAD_OR_DUAL_N
SPI_CLK_ASYNC --> ASYNC_SPI_CLK
MMCM_BUFIO_N --> MMCM_OR_BUFIO_N
SERDES_DDR_N --> SERDES_OR_DDR_N
CLK_ASYNC --> ASYNC_CLK
CLKS_ASYNC --> ASYNC_CLK
SERDES --> SERDES_OR_DDR_N
GTH_GTX_N --> GTH_OR_GTX_N
IF_TYPE --> DDR_OR_SDR_N
PARALLEL_WIDTH --> DATA_WIDTH
ADD_SUB --> ADD_OR_SUB_N
A_WIDTH --> A_DATA_WIDTH
CONST_VALUE --> B_DATA_VALUE
IO_BASEADDR --> BASE_ADDRESS
IO_WIDTH --> DATA_WIDTH
QUAD_DUAL_N --> QUAD_OR_DUAL_N
AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT
ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH
ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH
MODE_OF_ENABLE --> CONTROL_TYPE
CONTROL_TYPE --> LEVEL_OR_PULSE_N
IQSEL --> Q_OR_I_N
MMCM --> MMCM_OR_BUFR_N
2015-08-19 14:11:47 +03:00
6862655b0d
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-06-26 11:07:10 +02:00
8bd5fa5802
kc705: Common, fixed address range for the flash. Changed the start address so that it won't interfere with other cores
2015-05-23 00:10:06 +03:00
72b41c981f
kc705_base: Fix base address overlap
2015-03-18 10:33:17 +02:00
cea2d90eb2
base_kc705: Fix different issues
...
+ No more constant block inside IPI.
+ Gpio switch/led is on the axi_gpio first channel.
+ Fix the address map
+ Remove hdmi/spdif related constraints from base constraints
2015-03-16 19:10:57 +02:00
65654b77ff
fmcomms2_kc705: Update design to the new hdl framework
2015-03-13 18:54:28 +02:00
72e89852b6
daq2/kc705: 2014.4 updates
2015-01-14 12:58:08 -05:00
47871287f3
kc705: Updated base project with linear flash. Updated all depending projects
2015-01-13 10:19:07 +02:00
caa0268434
base_design: External IIC reset is connected to Vcc
...
External IIC reset is connected to Vcc in case of AC701, KC705 and VC707
2014-12-11 11:13:07 +02:00
a6b7b9d880
ad9467_kc705: Fix memory segment offset for SEG_axi_ddr_cntrl
2014-12-09 16:20:39 +02:00
3bc9b25e96
projects/common: KCU105 VC707 KC705 sync microblaze core defaults
...
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
2014-12-04 09:47:02 +01:00
12f1873e17
kc705_base: Define sys_addr_mem_seg for dmafifo
2014-11-26 15:08:55 +02:00
4f815b99a1
kc705_base: Fix sys_concat_intc input connections
...
All the unused input pins need to be connected to ground.
2014-11-03 13:02:08 +02:00
b92636c6eb
kc705_base: Interrupt update
2014-11-03 13:02:03 +02:00
a870603db5
common_bd: Update the common block designs to the new IRQ path
...
Avoid the use of xil_concat module by using the ad_interrupts.
2014-10-27 19:44:25 +02:00
7d3be14ab5
common: Connect audio clkgen reset
...
While we are at it also hide the unused locked pin.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-15 18:44:46 +03:00
fd89458708
common: Set cpu interconnect strategy to minimize area
...
There will rarely be concurrent access to the peripheral control bus
interconnect, so there is no need to optimize for performace. Setting the
interconnect strategy to minimize area can reduce the resource usage by
~90%.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-15 18:43:54 +03:00
d2a04856a9
common: Fix xlconstant output pin name
...
On 2014.2 xlconstant output pin name is 'dout'.
2014-10-15 15:37:06 +03:00
cd42345324
projects/common/xxx/xxx_system_bd.tcl: 'Update microblaze defaults
...
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
2014-10-07 09:17:24 +02:00
041d8faaf7
common: Updated common projects for ac701/kc702/zc702/zed to vivado 2014.2
2014-09-30 10:31:00 +03:00
41cc92ef49
Remove BASEADDR/HIGHADDR parameters
...
This is unused and unneeded. The AXI interconnect will make sure that a
peripheral only gets requests that are meant for it, there is no need to
check the address in the peripheral itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-11 12:26:37 +02:00
d0a8b4a63c
kc705,common: Mem_interconnect maximize performance
...
For FMCOMMS1, when both the ADC and DAC DMAs are active, the system was
unstable. With this fix, it the system seems to be stable.
2014-04-03 15:59:33 +03:00
fbafaa8507
MicroBlaze base system: Fix a few net names
...
Every interconnect interface net name follows the convention:
<interconnect name>_<interface name>
No changes in logic or any connection!
2014-04-01 10:40:35 +03:00
792e8a208d
KC705 base system: Make a few cosmetic changes
2014-03-24 12:55:37 +02:00
13b4dd07d0
KC705 base system: Modify interrupt concatanation
...
- Add an aditional interrupt input net for the sys_concat_aux_intc
module
2014-03-21 14:45:18 +02:00
c6143dbfaf
KC705 base system: Delete trailing whitespaces.
2014-03-21 14:42:27 +02:00
dc44703cf1
zynq/non-zynq: identical signal names and instances
2014-03-17 17:02:03 -04:00
a6da4ca01c
zynq/non-zynq merge variables
2014-03-17 16:39:52 -04:00
5c3b65d01b
adv7511: kc705/ac701 updates
2014-03-06 09:36:50 -05:00
3c0ea759a0
changed path settings
2014-03-03 10:06:02 -05:00
ddac1a8834
added common board files
2014-02-28 21:17:01 -05:00
Iulia Moldovan
PIoandan
Arpadi
Istvan Csomortani
AndreiGrozav
Adrian Costina
Rejeesh Kutty
Lars-Peter Clausen
Michael Hennerich