zcy
/
pluto_hdl_adi
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
6,574 Commits
1 Branch
0 Tags
23 MiB
Commit Graph

9 Commits (main)

Author SHA1 Message Date
Iulia Moldovan c9a7d4d927 Add copyright and license to .tcl, .ttcl files 
Signed-off-by: Iulia Moldovan <Iulia.Moldovan@analog.com>
 2023-07-25 15:22:26 +03:00
AndrDragomir 8b9175a80c projects: Fix intermitent timing violation on a10soc 
adrv9009, dac_fmc_ebz, ad9081_fmca_ebz, fmcomms8:
Increased PLACEMENT_EFFORT_MULTIPLIER global parameter to 1.2 for increased quality of placement
 2022-12-13 14:21:24 +02:00
Bogdan Luncan 72313df81f Updated the makefiles to build the projects in subdirectories based on the build parameters. 
Running 'make' will build the default project directly in the project folder (like it did before)
Running 'make RX_LANE_RATE=15 TX_LANE_RATE=15' will build the project inside the 'RXRATE15_TXRATE15' subdirectory.
Running 'make CFG=cfg/test_config.txt" will use the variables found inside the configuration file and build the project inside the 'test_config' subdirectory.
Running 'make clean' will clean the default project only.
Running 'make CFG=cfg/test_config.txt clean' will clean the 'testconfig' build.
Running 'make clean-all' will delete all the built configurations and libraries.

Note that the 'JESD' and 'LANE' words from the parameter names are stripped.

Signed-off-by: Bogdan Luncan <bogdan.luncan@analog.com>
 2022-11-14 09:38:42 +02:00
Iacob_Liviu 482f0489a3 scripts: Merge adi_env.tcl into a single file 
Move the new adi_env.tcl file from hdl/projects/scripts into hdl/scrips
 2022-08-08 13:52:54 +03:00
Istvan Csomortani 4684dc03ce dac_fmc_ebz/a10soc: Use balanced optimization mode 
Always a good idea to start from default, and change optimization mode
of the tool if it's strict necessary.
 2020-03-17 17:25:02 +00:00
Istvan Csomortani 253a8cb6ee dac_fmc_ebz/a10soc: Tool expect that all config parameters exists on top entity 2020-03-17 17:25:02 +00:00
Istvan Csomortani 5329458a62 library/scripts: Rename adi_ip_alt.tcl to adi_ip_intel.tcl 2019-06-29 06:53:51 +03:00
Istvan Csomortani ec67a381e4 adi_project: Rename the process adi_project_altera to adi_project 2019-06-29 06:53:51 +03:00
Lars-Peter Clausen 6d31a437aa dac_fmc_ebz: Add initial Arria10 SoC support 
Add support for the Arria 10 SoC development kit to the dac_fmc_ebz
project.

This allows to use the following FMC boards on the Arria 10 SoC development
Kit carrier:
  * AD9135-FMC-EBZ
  * AD9136-FMC-EBZ
  * AD9144-FMC-EBZ
  * AD9152-FMC-EBZ
  * AD9154-FMC-EBZ
  * AD9171-FMC-EBZ
  * AD9172-FMC-EBZ
  * AD9173-FMC-EBZ

Note that the board in its default configuration is not fully compatible with the
mentioned FMC boards and some slight re-work moving some 0 Ohm resistors is
required. The rework concerns the LA01 and LA05 pins, which by default are
not connected to the FPGA. The changes required are:

  LA01_P_CC
    R612: R0 -> DNI
    R610: DNI -> R0
  LA01_N_CC
    R613: R0 -> DNI
    R611: DNI -> R0
  LA05_P
    R621: R0 -> DNI
    R620: DNI -> R0
  LA05_N
    R633: R0 -> DNI
    R632: DNI -> R0

The main differences between AD9144-FMC-EBZ and AD9172-FMC-EBZ are:
  * The DAC txen signals are connected to different pins
  * The polarity of the spi_en signal is active low instead of active high
  * The maximum lane rate is up to 15.4 Gpbs

To accommodate this all 4 possible txen signals as well as the spi_en
signal are connected to GPIOs. Software can decide how to use them
depending on which FMC board is connected.

Note that each carrier has a maximum supported lane rate. Modes of the
AD9172 (and similar) that exceed the carrier specific limit can not be used
on that carrier. The limits are as following:
  * A10SoC: 14.2 Gbps
 2019-06-06 11:45:05 +03:00