This commit fixes the 16.5Gbps lane rate case where the link drops
after few seconds an initial successful link up happens.
A few seconds delayed calibration process can workaround this but with
having the differential drivers swing increased this is no longer
required.
This will allow building base test harnesses and place on top of them
existing block designs for simulation purposes.
Test harnesses will contain basic functionality like
- clock and reset generators
- AXI master to aid register access of the cores.
- memory model of the DDR
- interrupt controller
Existing procedures (ad_mem_hp0_interconnect, ad_cpu_interconnect, ... ) will
connect to this harness as they do to a real base design.
To support deterministic latency with non-power of two octets per frame
(F=3,6) the interface width towards the transport layer must be resized
to match integer multiple of frames.
e.g Input datapath width = 4; Output datpath width = 6;
for F=3 one beat contains 2 frames
for F=6 one beat contains 1 frame
The width change is realized with a gearbox.
Due the interface width change the single clock domain core is split
in two clock domains.
- Link clock : lane rate / 40 for input datapath width of 4 octets 8b10b
- lane rate / 20 for input datapath width of 8 octets 8b10b
- lane rate / 66 for input datapath width of 8 octets 64b66b
- Device clock : Link clock * input data path width / output datapath width
Interface to transport layer and SYSREF handling is moved to device clock domain.
The configuration interface reflects the dual clock domain.
If Input and Output datapath width matches, the gearbox is no longer
required, a single clock can be connected to both clocks.
In most of the standalone projects the generic project creation flow is not followed. The project's device
is defined manualy. This fix makes sure that those projects still builds without an issue.
NOTE: In these case we should use adi_project_create directly in system_project.tcl.
Without defining this signal, the UART lines receive garbage data
when no cable is connected to the J4 USB UART port.
The GPIO9 is enabled in the reference base design along with the
4MA CURRENT_STRENGTH constraint on the UART pins
When phase alignment is active, the PFD frequency value should be used
as outclk1 actual frequency.
The configuration interface of the fPLL does not support fractional values.
If the reference clock is fractional, the tool will throw an error that requirement
above is not respected.
Round up the reference clock for the SERDES and the lane rate in order to
overcome this issue, until it's not fixed by Intel.
When phase alignment is active, the PFD frequency value should be used
as outclk1 actual frequency.
The configuration interface of the fPLL does not support fractional values.
If the reference clock is fractional, the tool will throw an error that requirement
above is not respected.
Round up the reference clock for the SERDES and the lane rate in order to
overcome this issue, until it's not fixed by Intel.
When phase alignment is active, the PFD frequency value should be used
as outclk1 actual frequency.
The configuration interface of the fPLL does not support fractional values.
If the reference clock is fractional, the tool will throw an error that requirement
above is not respected.
Round up the reference clock for the SERDES and the lane rate in order to
overcome this issue, until it's not fixed by Intel.
-change the video memory interfacing from f2h_axi_slave to
f2h_sdram0
- add f2h_sdram1 port as the default interface for converter DMA
- set as default the full HD resolution at 60 FPS (pixel clock 148.5MHz)
- use a second 200MHz(198MHz) clock from the pixel_clk_pll, as DMA source
to destination clock.
Also modified the FIFO ports to have the same widths so that in a
future commit the bypass would be available for cases when the
sampling rate won't be the maximum rate or the number of channels
active will be less than maximum number of channels
Switch RX path reset to be controlled by the TPL and use
RX SYSREF as external synchronization for the ADC TPL
Use TX SYSREF for synchornizing the TX DDS
The device clocks are AC coupled LVDS lines without external termination.
For proper operation internal differential termination must be enabled,
the DQS_BIAS will DC bias the AC coupled signal to VCCO/2 (1.8/2) 0.9V
Added reference design for the ad9656 evaluation board coupled with the
zcu102 carrier board. The JESD204 communication link that transfers data
from the 4 ADCs to the FPGA has the following paramenters : L=4, M=4, S=1,
F=2, HD=0, N=16, NP=16. The JESD204 line rate is configured to be 2.5GHz.
Signed-off-by: Dan Hotoleanu <dan.hotoleanu@analog.com>
The coraz7s has an Arduino/chipKIT Shield connector with 6 Single-ended
and 8 Differential Analog inputs tied to Xilinx's XADC.
The CN0540 uses the A0-5 pins as single-ended ADC channels to monitor
the differential input, ADC driver, and buffer voltages.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Note, the current SCLK to spi_clk ratio is four. That means, the input
delay in the MISO line is 25% of the SCLK period.
If the SCLK to spi_clk ratio is changing, this constraint must be
updated.
Generate a higher frequency of spi_clk using an axi_clkgen. (MMCM)
CAUTION: ad7768-1 is still violating the standard SPI timing,
reducing the timing window significantly for the last bit (or last high
bit).
Ignore the following critical warning on DMAC instance:
Critical Warning (15003): "mixed_port_feed_through_mode" parameter of RAM atom
system_bd:i_system_bd|axi_dmac:axi_dmac_0|axi_dmac_transfer:i_transfer| \
dmac_request_arb:i_request_arb|dmac_dest_mm_axi:i_dest_dma_mm| \
altsyncram:bl_mem_rtl_0|altsyncram_0tp1:auto_generated|ram_block1a1
cannot have value "old" when different read and write clocks are used.
Due to the interface differences between HPS's AXI4 and DMA's AXI4, the
tool will try to automaticaly add some bridges between the two
interface. Unfortunatly it does generate timing issues at the f2sdram0
interface of the HPS instance. By explicitly instantiating an AXI
bridge, these timing issues disappears.
Laszlo Nagy
Owen McAree
vladimirnesterov
Sergiu Arpadi
stefan.raus
Adrian Costina
Istvan Csomortani
aholtzma
AndreiGrozav
IMoldovan
hotoleanudan
Sergiu Cuciurean
Stanca Pop
Stanca.Pop
Dragos Bogdan