* Added header license for the files that didn't have
* Modified parentheses
* Removed extra spaces at the end of lines
* Fixed parameters list to be each parameter on its line
* Deleted lines after endmodule and consecutive empty lines
* Fixed indentation
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
For Intel projects:
In cases where the clock of source synchronous interface is not routed
through a clock capable pin the DPA receive mode can't be used. Instead
the clock will be routed through a clock buffer from an IO to the clock
tree and from there to the IOPLL.
When having multiple 936x in parallel, this change enables the use of source
synchronous received clock from the master as sampling clock for other slaves.
This will eliminate skew between the interfaces since the data delays
are going to be tuned against the master clock after a multi-chip
synchronization (MCS) is done. This eliminates the clock crossing from
the slave to master domain inside the FPGA.
Sync the two valid signals to keep a fixed phase relationship between
the Rx ant Tx channels, this way avoiding +/- 1 sample differences
on the Tx-Rx latency between consecutive transfers.
Define a MIMO_ENABLE parameter for the core, which will insert
and additional de-skew logic to prevent timing issues coming from
the clock skew differences of two or multiple AD9361.
Common basic steps:
- Include/create infrastructure:
* Intel:
- require quartus::device package
- set_module_property VALIDATION_CALLBACK info_param_validate
* Xilinx
- add bd.tcl, containing init{} procedure. The init procedure will be
called when the IP will be instantiated into the block design.
- add to the xilinx_blockdiagram file group the bd.tcl and common_bd.tcl
- create GUI files
- add parameters in *_ip.tcl and *_hw.tcl (adi_add_auto_fpga_spec_params)
- add/propagate the info parameters through the IP verilog files
axi_clkgen
util_adxcvr
ad_ip_jesd204_tpl_adc
ad_ip_jesd204_tpl_dac
axi_ad5766
axi_ad6676
axi_ad9122
axi_ad9144
axi_ad9152
axi_ad9162
axi_ad9250
axi_ad9265
axi_ad9680
axi_ad9361
axi_ad9371
axi_adrv9009
axi_ad9739a
axi_ad9434
axi_ad9467
axi_ad9684
axi_ad9963
axi_ad9625
axi_ad9671
axi_hdmi_tx
axi_fmcadc5_sync
The ADC DMA will never underflow and unsurprisingly the adc_dunf signal is
never used anywhere. It is very unlikely it will ever be used, so remove
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DAC DMA will never overflow and unsurprisingly the dac_dovf signal is
never used anywhere. It is very unlikely it will ever be used, so remove
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
+ Add a HDL parameter for the PPS receiver module :
PPS_RECEIVER_ENABLE. By default the module is disabled.
+ Add the CMOS_OR_LVDS_N and PPS_RECEIVER_ENABLE into the CONFIG
register
+ Define a pps_status read only register, which will be asserted, if the free
running counter reach a certain fixed threshold. (2^28) The register can
be deasserted by an incomming PPS only.
The external s_axi_{awaddr,araddr} signals that are connect to the core
have their width set according to the specified size of the register map.
If the s_axi_{awaddr,araddr} signal of the core is wider (as it currently
is for many cores) the MSBs of those signals are left unconnected, which
generates a warning.
To avoid this make sure that the signal width matches the declared register
map size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The ad_pps_receiver is instantiated at the top of core.
The rcounter is placed into adc/dac_common registers space, at the
address 0x30 (word aligned).
The interrupt mask is placed into adc/dac_common, at the address 0x04
(word aligned). Because the core has an instance of both modules, the
interrupt masks are OR-ed together.
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
For a better timing and control, the valid control lines are gated with flops, instead of combinatorial logic.
This is the main reason why we do not need the tdd_enable_synced signal anymore. The out coming data is delayed by one clock cycle to keep data and control lines synced.
+ Define two control signal for util_tdd_sync : tdd_sync_en and tdd_terminal_type
+ Delete to old ad_tdd_sync.v instances from the core
+ Update Make files
+ Update ad_tdd_control: add additional CDC logic for tdd_sync (the sync comes from another clock domain)
+ Update the ad_tdd_sync module: it's just a simple pulse generator, the pulse period is defined using a parameter, pulse width is fixed: 128 x clock cycle
+ Update TDD regmap: tdd sync period is no longer software defined
The synchronization interface is a single bidirectional line. Output for Master, input for Slave.
The sync_period value is relative to frame length and the digital interface clock. The actual synchronization
period will be: sync_period * frame_length * fb_clock_cycle
This line controls the mux, which switch between hdl and software (GPIO) control of the ENABLE/TXNRX pins.
Fix the broken path and change the name from "tdd_enable" to "tdd_enabled".
Iulia Moldovan
Laszlo Nagy
Istvan Csomortani
AndreiGrozav
Lars-Peter Clausen
Rejeesh Kutty