c9a7d4d927
Add copyright and license to .tcl, .ttcl files
...
Signed-off-by: Iulia Moldovan <Iulia.Moldovan@analog.com>
2023-07-25 15:22:26 +03:00
e8ff32d6df
ad6676evb: Parameterize JESD204 configuration values
...
Added the capability to set the JESD204 configuration values from a single
point in the code and to modify these default settings from the command
line for the Xilinx FPGAs in the project.
Signed-off-by: Dan Hotoleanu <dan.hotoleanu@analog.com>
2022-01-31 10:36:31 +02:00
318523579f
ad6676evb: Update to JESD204 TPL instantiation
...
Updated the JESD204 TPL instantation of the design.
Signed-off-by: Dan Hotoleanu <dan.hotoleanu@analog.com>
2022-01-31 10:36:31 +02:00
5266d2ae88
ad6676evb: DMA should use $sys_dma_resetn
2019-06-13 10:59:43 +03:00
019390f9bf
block_design: Updates with new reset net variables
2019-06-11 18:13:06 +03:00
7960b00684
block_design: Update with new clock net variables
...
Using the new clock net variables in all Xilinx block designs.
2019-06-11 18:13:06 +03:00
da50d682c5
ad6766evb: Use new pack infrastructure
...
Use the new util_cpack2 and util_upack2 cores. They have lower utilization
that the old util_cpack and util_upack cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2018-11-28 11:33:11 +02:00
c81254200f
ad6676evb: Fix RX_DFE_LPM_CFG parameter, as the design is used in DFE mode
...
The parameter RX_DFE_LPM_CFG should be 0x954 for DFE and 0x904 in LPM
I've removed also QPLL_FBDIV parameter, as QPLL is not used in this design
2018-04-11 15:09:54 +03:00
041e448083
ad6676: Fix OUT_CLK_SEL configuration
...
The script specifies the OUT_CLK_SEL and SYS_CLK_SEL parameter values as
binary numbers. But the tools will interpret them as decimal number
resulting in the wrong selection for OUT_CLK_SEL. Specify the parameter
values as decimal values to avoid this.
This is not a critical issue since software will overwrite this setting at
system boot-up. But it should be fixed anyway.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2018-02-16 13:32:50 +01:00
0360e8587e
Connect JESD204 interrupts
...
Connect the ADI JESD204 link layer peripheral interrupt signals in all
projects.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-07-05 14:37:50 +02:00
5ca79e843c
ad6676evb: Convert to ADI JESD204
...
Convert the AD6676EVB project to the ADI JESD204 link layer core. The
change is very straight forward, but a matching change on the software side
is required.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-05-23 11:16:07 +02:00
0442e7d404
util_adxcvr: Fix parameter setup at instantiation
...
If a parameter value is defined as a string binary (e.g. "001001000000"),
it can confuse the tool, and the value may be used as a decimal number.
To prevent this issue and to improve readability converting all the binary
constants into hexadecimal.
2017-04-27 15:35:39 +03:00
bc9483c5a2
Ip automatic version: Update ad*/common/ad*_bd.tcl
...
ad6676evb/common/ad6676evb_bd.tcl
ad7616_sdz/common/ad7616_bd.tcl
ad7768evb/common/ad7768evb_bd.tcl
ad9265_fmc/common/ad9265_bd.tcl
ad9434_fmc/common/ad9434_bd.tcl
ad9467_fmc/common/ad9467_bd.tcl
ad9739a_fmc/common/ad9739a_fmc_bd.tcl
adrv9371x/common/adrv9371x_bd.tcl
adv7511/common/adv7511_bd.tcl
fmcadc4/common/fmcadc4_bd.tcl
2017-04-10 18:52:37 +03:00
5b5c0dde99
ad6676evb: Set default xcvr parameters to common design
2017-03-01 11:32:17 +02:00
67390c2a95
ad6676evb: Update projects with ad_sysref_gen
2016-12-19 10:52:25 +00:00
3a2c889115
ad6676evb: Update GT configuration
2016-12-14 17:55:49 +02:00
e5d3bae54d
projects/ad6676-adrv9371: xcvr updates
2016-11-23 11:06:22 -05:00
d6918de19e
ad6676: Update projects to xcvr frame work
2016-11-10 10:39:46 +02:00
4248b9373a
ad6676evb: Update to Vivado 2016.2
2016-08-30 16:08:07 +03:00
38c3f7474a
ad6676: Updated common design to 2015.4
2016-03-17 11:40:46 +02:00
a49230ec07
ad6676evb: Updated project to 2015.2.1
...
- updated to the new jesd framework
- added cpack core
2015-09-25 14:44:46 +03:00
0f553a08e8
ad6676evb: Drop explicit axi_dmac clock synchronicity configuration
...
The axi_dmac core is now capable of detecting whether its different parts
run in different clock domains or not. No need to configure it manually any
more.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-09-18 15:27:21 +02:00
d52308f074
axi_dmac: Change parameter name 2D_TRANSFER
...
Parameter name can't start with numbers, 2D_TRANSFER was changed to DMA_2D_TRANSFER
2015-08-20 10:14:22 +03:00
57cfb7cfb1
hdl/library: Update the IP parameters
...
The following IP parameters were renamed:
PCORE_ID --> ID
PCORE_DEVTYPE --> DEVICE_TYPE
PCORE_IODELAY_GROUP --> IO_DELAY_GROUP
CH_DW --> CHANNEL_DATA_WIDTH
CH_CNT --> NUM_OF_CHANNELS
PCORE_BUFTYPE --> DEVICE_TYPE
PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE
CHID --> CHANNEL_ID
PCORE_DEVICE_TYPE --> DEVICE_TYPE
PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N
PCORE_SERDES_DDR_N --> SERDES_DDR_N
PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE
DP_DISABLE --> DATAPATH_DISABLE
PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE
C_BIG_ENDIAN --> BIG_ENDIAN
C_M_DATA_WIDTH --> MASTER_DATA_WIDTH
C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH
NUM_CHANNELS --> NUM_OF_CHANNELS
CHANNELS --> NUM_OF_CHANNELS
PCORE_4L_2L_N -->QUAD_OR_DUAL_N
C_ADDRESS_WIDTH --> ADDRESS_WIDTH
C_DATA_WIDTH --> DATA_WIDTH
C_CLKS_ASYNC --> CLKS_ASYNC
PCORE_QUAD_DUAL_N --> QUAD_DUAL_N
NUM_CS --> NUM_OF_CS
PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID
PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID
PCORE_CLK0_DIV --> CLK0_DIV
PCORE_CLK1_DIV --> CLK1_DIV
PCORE_CLKIN_PERIOD --> CLKIN_PERIOD
PCORE_VCO_DIV --> VCO_DIV
PCORE_Cr_Cb_N --> CR_CB_N
PCORE_VCO_MUL --> VCO_MUL
PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC
PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH
PCORE_ADDR_WIDTH --> ADDRESS_WIDTH
DADATA_WIDTH --> DATA_WIDTH
NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS
DEBOUNCER_LEN --> DEBOUNCER_LENGTH
ADDR_WIDTH --> ADDRESS_WIDTH
C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED
Cr_Cb_N --> CR_CB_N
ADDATA_WIDTH --> ADC_DATA_WIDTH
BUFTYPE --> DEVICE_TYPE
NUM_BITS --> NUM_OF_BITS
WIDTH_A --> A_DATA_WIDTH
WIDTH_B --> B_DATA_WIDTH
CH_OCNT --> NUM_OF_CHANNELS_O
M_CNT --> NUM_OF_CHANNELS_M
P_CNT --> NUM_OF_CHANNELS_P
CH_ICNT --> NUM_OF_CHANNELS_I
CH_MCNT --> NUM_OF_CHANNELS_M
4L_2L_N --> QUAD_OR_DUAL_N
SPI_CLK_ASYNC --> ASYNC_SPI_CLK
MMCM_BUFIO_N --> MMCM_OR_BUFIO_N
SERDES_DDR_N --> SERDES_OR_DDR_N
CLK_ASYNC --> ASYNC_CLK
CLKS_ASYNC --> ASYNC_CLK
SERDES --> SERDES_OR_DDR_N
GTH_GTX_N --> GTH_OR_GTX_N
IF_TYPE --> DDR_OR_SDR_N
PARALLEL_WIDTH --> DATA_WIDTH
ADD_SUB --> ADD_OR_SUB_N
A_WIDTH --> A_DATA_WIDTH
CONST_VALUE --> B_DATA_VALUE
IO_BASEADDR --> BASE_ADDRESS
IO_WIDTH --> DATA_WIDTH
QUAD_DUAL_N --> QUAD_OR_DUAL_N
AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT
ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH
ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH
MODE_OF_ENABLE --> CONTROL_TYPE
CONTROL_TYPE --> LEVEL_OR_PULSE_N
IQSEL --> Q_OR_I_N
MMCM --> MMCM_OR_BUFR_N
2015-08-19 14:11:47 +03:00
6862655b0d
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-06-26 11:07:10 +02:00
71b5004b25
projects- drp moved to up-clock domain
2015-06-01 14:57:59 -04:00
e332fa01c8
ad6676evb, daq2, fmcadc2, fmcjesdadc1, usdrx1: Updated jesd reset connection
2015-04-30 12:11:46 +03:00
5afcfa37a7
ad6676evb: changed the dma clock
2015-04-03 18:27:46 +03:00
7456ca67a8
ad6676evb: 2014.4 updates
2015-03-17 16:53:13 -04:00
d75487d0a2
ad6676_fmc: Fix GT lane number definition
2014-11-26 10:45:00 +02:00
3211964c2e
ad6676evb: added
2014-11-10 13:41:01 -05:00
Iulia Moldovan
Dan Hotoleanu
Istvan Csomortani
Lars-Peter Clausen
Adrian Costina
AndreiGrozav
Rejeesh Kutty