* Added header license for the files that didn't have
* Modified parentheses
* Removed extra spaces at the end of lines
* Fixed parameters list to be each parameter on its line
* Deleted lines after endmodule and consecutive empty lines
* Fixed indentation
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
The new REG_PRBS_CNTRL and REG_PRBS_STATUS registers expose controls of internal
PRBS generators and checkers allowing the testing the multi-gigabit serial link
at the physical layer without the need of the link layer bringup.
Common basic steps:
- Include/create infrastructure:
* Intel:
- require quartus::device package
- set_module_property VALIDATION_CALLBACK info_param_validate
* Xilinx
- add bd.tcl, containing init{} procedure. The init procedure will be
called when the IP will be instantiated into the block design.
- add to the xilinx_blockdiagram file group the bd.tcl and common_bd.tcl
- create GUI files
- add parameters in *_ip.tcl and *_hw.tcl (adi_add_auto_fpga_spec_params)
- add/propagate the info parameters through the IP verilog files
axi_clkgen
util_adxcvr
ad_ip_jesd204_tpl_adc
ad_ip_jesd204_tpl_dac
axi_ad5766
axi_ad6676
axi_ad9122
axi_ad9144
axi_ad9152
axi_ad9162
axi_ad9250
axi_ad9265
axi_ad9680
axi_ad9361
axi_ad9371
axi_adrv9009
axi_ad9739a
axi_ad9434
axi_ad9467
axi_ad9684
axi_ad9963
axi_ad9625
axi_ad9671
axi_hdmi_tx
axi_fmcadc5_sync
Fix the following warning:
WARNING: [Synth 8-2611] redeclaration of ANSI port up_es_reset is not allowed
Also make sure, that in all configurations, the register has a diver.
Expose the TX configurable driver ports, more specifically the
TX_DIFFCTRL, TX_POSTCURSORE and TX_PRECURSORE for software. This
provides a soft tunning capability of the transmit side of the
transceivers, in cases where the insertion loss of the channel is too
high or low, comparing to the default value supported by the default
configuration of the GTs.
You can find information about these configuration ports under the
section called 'TX Configurable Driver' in the GT transceivers user
guide. (UG476, UG576)
The util_adxcvr supports GTX2, GTH3 and GTH4. The transceiver is selected
using the XCVR_TYPE parameter.
The axi_adxcvr on the other hand only has a configuration parameter to
indicate whether a GTX or GTH transceiver is used (GTH_OR_GTX_N). Since
there are some minor differences between GTH3 and GTH4 that software needs
to know about rename the GTH_OR_GTX_N to XCVR_TYPE and match use the same
semantics as util_adxcvr.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
Iulia Moldovan
Filip Gherman
Laszlo Nagy
Istvan Csomortani
AndreiGrozav
Adrian Costina
Lars-Peter Clausen
Rejeesh Kutty
Shrutika Redkar