f9ffaf457d
projects/daq2- drp moved to up clock
2015-06-01 13:39:26 -04:00
f232a36141
common: Place HDMI interface registers into the IOB
...
The paths from the HDMI interface registers to the IO pads are
unconstrained. This means the P&R can in theory put the register anywhere
which could lead to stability issues on the interface, depending on what
else is in the fabric. To get predictable delays for the register to IO pad
path place the register into the IOB section.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-23 14:33:47 +02:00
1d66cf63b6
common: zc706: Use interface connection for the HDMI DMA stream
...
Use a interface connection for the HDMI DMA stream instead of individually
connecting each of the signals. This make things a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-08 13:29:25 +02:00
6d0a2bf64c
axi_adcfifo: added
2015-04-07 16:21:39 -04:00
68361bafd4
zc706_base: The FCLK_CLK2 is not used.
2015-03-11 18:10:32 +02:00
8967903d76
zc706: intr sensitivity level-high
2015-03-10 16:05:05 -04:00
f0395b646c
plddr3: ad_connect updates
2015-03-09 16:07:37 -04:00
031dffa80c
zc706: move gpio/spi to base design
2015-03-09 16:07:02 -04:00
91765fdd82
daq2+base: board tcl updates
2015-03-05 10:56:36 -05:00
65d9f08763
zc706: mig 2014.4
2015-01-09 14:12:52 -05:00
868df1aac8
zc706: mig 2014.4
2015-01-09 14:12:51 -05:00
0de1a38245
zc706: 2014.4 update
2014-12-23 14:03:52 -05:00
59e610be09
zc706_constr: Move the sys_rst related constraint definition to zc706_system_mig_constr.xdc
2014-12-17 19:07:43 +02:00
77fa96fa67
plddr3: sys-rst from board pushbutton
2014-12-15 12:58:54 -05:00
ed7f8b4908
plddr3: sys-rst from board pushbutton
2014-12-15 12:58:44 -05:00
34ffa15b12
zynq_plddr3: Fix PLDDR3's Reset Generator
...
Reset generator's external reset signal was active low, but the GT reset is active high, and both the DDR controller and FIFO2S were in reset.
Therefore the external reset active state is changed to active high. This setup in general is made by the tool automatically, in order to do it correctly, need to
set this two property of the reset generator.
2014-12-04 15:39:17 +02:00
c6af2696b3
plddr3: internal buswidth/clock conversion
2014-11-12 14:43:48 -05:00
2e01ad2eec
ad9625_fmc/zc706: ps7 interrupt updates
2014-10-29 12:13:44 -04:00
a870603db5
common_bd: Update the common block designs to the new IRQ path
...
Avoid the use of xil_concat module by using the ad_interrupts.
2014-10-27 19:44:25 +02:00
767179dce9
adv7511_zc706: Fix IRQ layout
...
Fix IRQ connection, this layout works on Linux
2014-10-21 17:44:28 +03:00
6d76e0b768
zc706: remove top level constraints
2014-10-15 14:51:02 -04:00
5715c5b28f
dmafifo: axi stream interface
2014-10-15 14:50:57 -04:00
7d3be14ab5
common: Connect audio clkgen reset
...
While we are at it also hide the unused locked pin.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-15 18:44:46 +03:00
fd89458708
common: Set cpu interconnect strategy to minimize area
...
There will rarely be concurrent access to the peripheral control bus
interconnect, so there is no need to optimize for performace. Setting the
interconnect strategy to minimize area can reduce the resource usage by
~90%.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-15 18:43:54 +03:00
43e9b0c7a6
common: Disable TTC0 MMIO routing for PS7
...
We do not use the ttc0 to MMIO routing, but it is enabled by default, so
explicitly disable it.
2014-10-10 16:19:51 +03:00
7c98a783c5
2014.2 updates
2014-09-23 12:32:33 -04:00
dd7bac41c1
daq1 : Update project to 2014.2
...
- Cores are upadted
- Concat module does not swap output anymore
- Clock signal name ps7_clk_* changed to clk_fpga_*
2014-09-22 17:33:50 +03:00
41cc92ef49
Remove BASEADDR/HIGHADDR parameters
...
This is unused and unneeded. The AXI interconnect will make sure that a
peripheral only gets requests that are meant for it, there is no need to
check the address in the peripheral itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-11 12:26:37 +02:00
a49eb5853b
ZED, ZC702: Added contraints so that projects can successfully synthesize on linux systems
...
For ZC706 Fixed one constraint which was not correct
2014-08-26 16:28:41 +03:00
6c6cab0e16
fmcomms2: ZC706 modified constraints for linux build machines
...
The added constraints allow the project to successfully pass timing on some ubuntu or debian build machines.
2014-08-01 17:34:36 +03:00
db1c931736
ad9625_plddr: PL DDR3 fixes
...
- Modified the axi slave interface handler
- Increased the rfifo_mem input depth to prevent overflow
2014-07-23 19:34:44 +03:00
2b6ce1e504
zc706_plddr3 : Fix axi_fifo2s_axi_mrst net
2014-07-21 15:10:36 +03:00
2955b9db78
fifo2s: flush if no request, c5soc: 14.0
2014-07-15 16:25:33 -04:00
b434fe6dd5
fmcomms5: register map changes
2014-07-08 16:57:43 -04:00
e38813fa9f
fifo- monitor status signals
2014-06-25 12:15:13 -04:00
57bb3705f2
zc706-plddr3: read changes to lower dma clock
2014-06-25 09:20:58 -04:00
c789dce77e
ad9625/zc706: added pl ddr3 fifo changes
2014-05-29 12:59:29 -04:00
56ddce1e8c
dmac: create fifo interface to avoid being treated as axi control stream
2014-05-27 10:25:14 -04:00
f73819f4d4
zc706: pl ddr3 initial checkin
2014-05-13 16:19:53 -04:00
fbfd658f0d
zc706: added pl ddr3 mig
2014-04-09 15:58:12 -04:00
f9a67371c0
Zynq Base System: Reset is synchronized to lowest system clock
...
System reset (sys_100m_reset) is synchronized to lowest system
clock (FCLK0), via a Processor System Reset module
2014-03-26 17:58:14 +02:00
dc44703cf1
zynq/non-zynq: identical signal names and instances
2014-03-17 17:02:03 -04:00
a6da4ca01c
zynq/non-zynq merge variables
2014-03-17 16:39:52 -04:00
f3ae57a53e
global clock and reset names
2014-03-11 09:57:59 -04:00
ddac1a8834
added common board files
2014-02-28 21:17:01 -05:00
Rejeesh Kutty
Lars-Peter Clausen
Istvan Csomortani
Adrian Costina