In MM2S applications like video DMA it is useful to mark the end of the stream
with the TLAST.
The change enables the generation of the TLAST on the last beat of the
last row of the 2d transfer.
The index on MSB of addresses was set to 31,
but the width of address in the axi_dmac depends on a parameter.
The mismatch causes issues in the Xilinx simulator which does not extends the
narrower width signal with zeros, instead the wider signal gets 'Z' on its MSBs.
When the address was incremented with the stride it became 'X' due the uninitialized
MSBs.
This change adds a diagnostic interface to the DMAC core.
The interface exposes internal information about the core,
information which can't be exposed through AXI registers
due the latency and update rate.
Such information is the fullness of the internal buffer.
For this is exposed in bursts and is driven from the destination
clock domain, as this is reflected in its name.
The signal has a fixed size and is dimensioned by
taking in account the supported maximum number of bursts of 128.
For the memory-mapped AXI read interface the slave asserts rlast for the
last beat in a burst.
This means we don't have to count the number of beats to know when the
burst is completed but instead can use rlast. This slightly reduces the
amount of resources needed for the MM-AXI source module and given that the
beat_counter is often the bottleneck timing wise this should also improve
the timing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DMAC allows a transfer to be aborted. When a transfer is aborted the
DMAC shuts down as fast as possible while still completing any pending
transactions as required by the protocol specifications of the port. E.g.
for AXI-MM this means to complete all outstanding bursts.
Once the DMAC has entered an idle state a special synchronization signal is
send to all modules. This synchronization signal instructs them to flush
the pipeline and remove any stale data and metadata associated with the
aborted transfer. Once all data has been flushed the DMAC enters the
shutdown state and is ready for the next transfer.
In addition each module has a reset that resets the modules state and is
used at system startup to bring them into a consistent state.
Re-work the shutdown process to instead of flushing the pipeline re-use the
startup reset signal also for shutdown.
To manage the reset signal generation introduce the reset manager module.
It contains a state machine that will assert the reset signals in the
correct order and for the appropriate duration in case of a transfer
shutdown.
The reset signal is asserted in all domains until it has been asserted for
at least 4 clock cycles in the slowest domain. This ensures that the reset
signal is not de-asserted in the faster domains before the slower domains
have had a chance to process the reset signal.
In addition the reset signal is de-asserted in the opposite direction of
the data flow. This ensures that the data sink is ready to receive data
before the data source can start sending data. This simplifies the internal
handshaking.
This approach has multiple advantages.
* Issuing a reset and removing all state takes less time than
explicitly flushing one sample per clock cycle at a time.
* It simplifies the logic in the faster clock domains at the expense of
more complicated logic in the slower control clock domain. This allows
for higher fMax on the data paths.
* Less signals to synchronize from the control domain to the data domains
The implementation of the pause mode has also slightly changed. Pause is
now a simple disable of the data domains. When the transfer is resumed
after a pause the data domains are re-enabled and continue at their
previous state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Move the transfer logic, including the 2d module, into its own sub-module.
This allows testing of the full transfer logic independently of the
register map logic.
The top-level module now only instantiates the register map and transfer
module, but does not have any logic on its own.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Laszlo Nagy
Lars-Peter Clausen