There are boards (e.g. AD4630-24) which take the SCLK and echo back to
the FPGA through a level shifter - doing this removes the effect of
round-trip timing delays from the level shifter. This is commonly done
whenever isolators are used since they are very slow.
By setting the ECHO_SCLK parameter to 1, the IP will use the incoming
echoed SCLK clock to latch the SDI line(s). The sdi_data_valid is still
synchronous to the SPI clock, and it's generated after the last valid
SDI latch.
The designer's responsibility is to time the SDI shift registers in order to
respect the design requirements.
Fix the *_ip.tcl scripts for axi_spi_engine and spi_engine_offload
module.
In case of a bool parameters the value_format and value properties must
be set for both user and hdl paramters. If not, in the generated verilog
code the tool will use "true" or "false" strings, instead of 0 or 1.
The sdo_enabled and sdi_enabled control lines are generated from the
current state of the CMD bus.
In case of a delayed SDI latching the sdi_enabled can be deasserted at
the moment of the last valid bit, losing the generation of the sdi_data_valid
signal, which eventually cause a data loss, or even deadlock on software driver.
To make the logic mode robust, latch the value of the CMD[9:8] at every
transfer command. Doing so the sdo_enabled and sdi_enabled control lines will
store the last active transfer command state and they will be
independent of the current state of the CMD bus. This way we can add
longer time delay to the SDI latching if it's necessary.
The commit 9ab88f1200 introduced a new
feature for the execution module, which provides the possibility to
delay the SDI line latch with one or more core clock cycle. Unfortunatly
the implementation was not correct and the SDI line was latched at the
wrong time.
This patch fix the aligment of the shift register and the SDI_DELAY parameter,
to latch the SDI line of the physical interface at the right time.
Improve the description of the feature.
xsim does not like if a register or wire is used before their
definition. Make sure the every register and wire is defined before it's
used the first time.
There are devices where the SDO default state, between transactions, is
not GND, rather VCC.
Define a parameter, which can be used to set the default state of the
SDO line.
For consistent simulation behavior it is recommended to annotate all source
files with a timescale. Add it to those where it is currently missing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
By changing the parameter called SDI_DATA_WIDTH the spi framework can support multiple SDI lines.
The supported number of SDI lines are: 1, 2, 3 and 4.
SPI Engine is a highly flexible and powerful SPI controller framework. It
consist out of multiple sub-modules which communicate over well defined
interfaces. This allows a high degree of flexibility and re-usability while
at the same time staying highly customizable and easily extensible.
Currently included are four components:
* SPI Engine execution module: The excution module is responsible for
handling the low-level physical interface SPI logic.
* SPI Engine AXI interface module: The AXI interface module allows
memory mapped acccess to a SPI bus control stream and can be used to
implement a software driver that controls the SPI bus.
* SPI Engine offload module: The offload module allows to store a
predefined SPI Engine command and data stream which will be send out
when a external trigger signal is asserted.
* SPI Engine interconnect module: The interconnect module allows to
combine multiple control streams into a single stream giving multiple
control modules access to a execution module.
For more information see: http://wiki.analog.com/resources/fpga/peripherals/spi_engine
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Adrian Costina
Iacob_Liviu
stefan.raus
Istvan Csomortani
Stanca Pop
Arpadi
Lars-Peter Clausen
Rejeesh Kutty