* Added header license for the files that didn't have
* Modified parentheses
* Removed extra spaces at the end of lines
* Fixed parameters list to be each parameter on its line
* Deleted lines after endmodule and consecutive empty lines
* Fixed indentation
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
When using a non-maximum sampling rate the data is captured earlier by two
samples.
After the initial trigger jitter fix, a low latency/utilization was
desired(one sample delay for the trigger detection). After adding the
instrument trigger an equal latency between ADC and LA was required, hence the
need for a two sample delay on the trigger path. The delay was implemented
as two clock cycle delays not two sample delays.
This commit fixes this issue and offers a more robust design.
A trigger jitter was added by fix on the external trigger input. It
manifests at input sampling frequencies lower than the maximum frequency.
Added the required reset and CE(valid) signal to the last output
stages of the trigger to obtain the desired functionality for all
sampling rates.
The extra delay was added on the trigger and data paths to compensate
for the logic analyzer changes.
The extra delay will be also seen on the m2k daisy chain. The
delay between devices will be increased from 3 to 4 samples delay.
Currently trigger out pin is hold for 1ms in the next translation(t+1)
state(0 or 1). But not in the state that follows (t+2). This commit
fixes this issue and simplifies the logic.
The decimation module controls the valid signal. The whole triggering mechanism
is active only when the valid signal is active.
In the case of low sampling rates, the valid signal is active once every
n clock cycles. If an external trigger condition is fulfilled and the data valid
signal is low at the time, that trigger will be ignored by the DMA.
To solve this issue, the trigger is held high until the valid is asserted.
And it stays high for at least one clock cycle.
- Add embedded trigger as an option. The use of the embedded trigger as an
option in the data stream is done for further processing, keeping the data
synchronized with the trigger.
When instrument (module) trigger is desired (logic_analyzer - adc_trigger),
a small propagation time is required, hence the need to remove the
util_extract(trigger extract) module from the data path.
- Add more options for the IO triggering. This will open the door for multiple
M2k synchronization(triggering).
trigger_o mux:
1 - trigger flag (from regmap)
2 - external pin trigger (Ti)
3 - external pin trigger (To)
4 - internal adc trigger
5 - logic analyzer trigger
The signal passed to trigger_o must not be delayed, but the new value has to be
kept for a short period, 1ms (100000 clock cycles), to reduce switch noises in
the system.
The axi_adc_trigger handles 3 output triggers:
- trigger_o - external trigger (1 clock cycle delay)
- trigger_out - signals on dmac/fifo_wr_sync the start of a new transfer.
A variable fifo depth is present in the data path, which delays the data
arriving at the DMA with 3 clock cycles. By coincidence, the external trigger
is synchronized and detected on 3 clock cycles. To get a maximum optimization
the trigger_out will be delayed with 3 clock cycles for internal triggers and
directly forwarded in the case of an external trigger.
- trigger_out_la (cascade trigger for logic_analyzer - m2k example)
Because the trigger_out_la must have a small delay, to get a realible
instrument triggering mechanism, a 1 delay clock cycle must be added on the
trigger paths, to avoid creating a closed combinatorial loop.
Increase pcore version. The major version 3 is used to describe the instrument
trigger updates.
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The up_xfer_cntrl and up_xfer_status modules have its own constraints files
in library/xilinx/common. Each IP which has an instance of these
modules, have to use these constraints files.
The following IPs were modified:
- axi_adc_decimate
- axi_adc_trigger
- axi_dac_interpolate
- axi_logic_analyzer
If the streaming bit is set, after the trigger condition is met,
data will be continuosly captured by the DMA. The streaming bit
must be set to 0 to reset triggering.
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
The axi_adc_trigger does not use the full width of the AXI interface
address. It only responds to register access in the first 32 registers.
Reduce the size of the AXI address to 7 bit accordingly. This allows the
scripts to correctly infer the internal register map size which will cause
the interconnect to filter out access to these unused register.
This slightly reduces utilization by getting rid of some pipeline
registers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The current implementation doesn't quite work right when the interface
clock is slower than the trigger clock and also causes timing issues.
Disable it temporarily until a proper CDC transfer is implemented.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Xilinx recommends that all synchronizer flip-flops have
their ASYNC_REG property set to true in order to preserve the
synchronizer cells through any logic optimization during synthesis
and implementation.
Iulia Moldovan
Iacob_Liviu
Adrian Costina
AndreiGrozav
Arpadi
Istvan Csomortani
Lars-Peter Clausen