28aea82952
fmcomms2_zc702: Add SPI and GPIO interface for FREQCVT
2015-07-22 10:16:04 +03:00
a7da779b94
Makefile: Updated Makefiles
2015-07-16 18:19:42 +03:00
1dcbf5e5a2
fmcomms2/zc706: Fix GPIO connections
...
Fix GPIO connections for the FREQCVT board.
2015-07-15 15:12:01 +03:00
a38339a3ec
fmcomms2/rfsom: Add GPIO control for the RF card
2015-07-14 13:12:54 +03:00
ba2029a6e8
fmcomms2/rfsom: Delete trailing whitespaces from system_constr.xdc
2015-07-14 13:12:53 +03:00
46fa91d5be
Makefile: Update Make files
2015-07-03 18:08:57 +03:00
95500d4022
fmcomms2_rfsom: Fix GPIO connections
2015-07-03 13:03:19 +03:00
0102e3e02c
fmcomms2_ALL: Preserve backward compatibility for ENABLE/TXNRX control
...
By default the ENABLE/TXNRX pins are controlled by GPIOs, if the TDD module is enabled, the TDD FSM will take over the control of these two pins.
2015-07-01 13:54:01 +03:00
6862655b0d
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-06-26 11:07:10 +02:00
25e56a4d03
arradio: renamed fmcomms2 c5soc to arradio
2015-06-08 11:35:21 +03:00
dc7064ab95
fmcomms2/vc707 - wfifo changes
2015-06-05 12:44:04 -04:00
25f1ad73f0
fmcomms2/freqcvt: Update SPI interface I/O
2015-06-05 18:16:14 +03:00
f1e75963a2
fmcomms2: wfifo+pack changes
2015-06-05 09:20:50 -04:00
3b1ea7e528
axi_ad9361/tdd: Cherry picked commit 598ece4 from hdl_2015_r1 branch
...
598ece4c8d
2015-06-04 18:09:47 +03:00
f81d22a17a
altera- common timing check
2015-06-04 10:56:32 -04:00
a6cae6b477
iobuf: do is a system verilog keyword
2015-05-21 14:06:17 -04:00
6b9906b22b
Refresh Makefiles
...
Re-generate the Makefiles after a small update to the generation script:
- Entries are sorted alphabetically
- Empty dependency lines are skipped
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-05-21 14:21:54 +02:00
0805da3b6b
fmcomms2/rfsom- enable dac delay
2015-05-18 16:45:54 -04:00
3e51d29f75
enable/txnrx- tdd changes
2015-05-18 14:28:20 -04:00
c19749361d
Makefiles: Updated makefiles to have as a result the programming file instead of the project file.
...
Also fixed altera projects dependencies
2015-05-18 17:22:46 +03:00
d9a124b767
fmcomms2_zc706: TDD integration, initial commit.
2015-05-11 12:20:45 +03:00
293ec6a319
fmcomms2: c5soc project updated to 14.1
2015-05-08 17:44:16 +03:00
91279253ef
Makefiles: Added mig project file as a dependency for Microblaze based projects. Also updated usdrx1 a5gt Makefile
2015-05-08 15:31:40 +03:00
949abcdc8f
Makefile: Updated makefiles so that the project recipe does not depend on lib
2015-05-06 14:58:29 +03:00
319f821fab
zc706pr - makefile
2015-05-04 13:41:03 -04:00
ab85e2ba36
zc706pr - 706 partial reconfiguration
2015-05-04 12:36:57 -04:00
c3dd9258e7
zc706: project mode
2015-05-04 10:25:12 -04:00
62acd37fee
zc706: project mode
2015-05-04 10:25:07 -04:00
ad551a0073
itx045: updates
2015-05-01 16:18:43 -04:00
00cafd4df0
fmcomms2/zc706: add partial reconfiguration
2015-05-01 12:23:18 -04:00
3641d8f714
fmcomms2/zc706: add partial reconfiguration
2015-05-01 12:23:11 -04:00
75a81d67d8
fmcomms2/zc706: add partial reconfiguration
2015-05-01 12:23:07 -04:00
140c622c8b
prcfg: common files
2015-05-01 11:48:09 -04:00
a8d4c916c1
fmcomms2_bd: remove axi3 switch
2015-05-01 11:47:29 -04:00
3fd830b038
fmcomms2: Use AXI3 interface for the DMA on ZYNQ
...
On ZYNQ the HP interconnects have a AXI3 interface. The DMA controller
supports both AXI4 and AXI3. By switching to AXI3 there is no need to create
a protocol converter between the DMA and the HP port.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-17 19:51:37 +02:00
71d4f3a474
fmcomms2: Don't mark synchronous paths as asynchronous for the DMAs
...
The AXI master interface and the register map AXI slave interface use the
same clock. No need to mark the interfaces as asynchronous. This removes the
need for CDC logic on those paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-17 19:51:37 +02:00
dc2b37bd0c
Makefile: Added top level Makefile. Modified behavior of clean and clean-all
...
Clean ran for a project will clean only the project files.
Clean-all ran for a project will clean also the library files on which the project depends.
The clean commands will only remove specific files and directories.
The top Makefile allows several options(per suggestion from jameyhicks):
make fmcomms1.zed will run "make all" in projects/fmcomms1/zed/
make clean will run "make clean" for all the projects
make clean-all will run "make clean" for all the projects and libraries
make lib will run "make all" for the library files
2015-04-17 17:22:38 +03:00
374f82e7de
makefiles: The clean command for library won't remove the xml files, except for component.xml.
...
Updated also the dmac dependencies
2015-04-16 11:53:27 +03:00
780455d68c
Makefile: Updated makefiles. Added makefiles for altera
2015-04-09 17:57:06 +03:00
5f8e9a74ea
makefile: updated
2015-04-07 16:32:01 -04:00
f79a152958
Makefiles: updated all makefiles adding clean functionality
2015-04-03 11:57:54 +03:00
9745462d88
fmcomms2: VC707 fixed top file
2015-04-02 15:31:40 +03:00
9dac22c814
fmcomms2: ZC702 fixed GPIOs in top file
2015-04-02 15:30:41 +03:00
dbbdeeaa0c
fmcomms1: Updated AC701 project to new framework
2015-04-02 11:22:16 +03:00
a4e9dd5fc4
fmcomms2: KC705 updated project
2015-04-02 11:21:13 +03:00
c46866e78c
makefile: added
2015-04-01 16:29:42 -04:00
c5a67ad1cd
makefile: added
2015-04-01 16:29:41 -04:00
74d3d458da
makefile: added
2015-04-01 16:29:39 -04:00
b1cc047d04
makefile: added
2015-04-01 16:29:38 -04:00
25a6a75a32
makefile: added
2015-04-01 16:29:37 -04:00
Istvan Csomortani
Adrian Costina
Lars-Peter Clausen
Rejeesh Kutty