078a7fffc8
fmcomms2: Use new pack/unpack infrastructure
...
Use the new util_cpack2 and util_upack2 cores. They have lower utilization
that the old util_cpack and util_upack cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2018-11-28 11:33:11 +02:00
fa6f45a406
adrv936x, fmcomms2/5, usrpe31x: Fix warning on the dac path
...
Fix warnining regarding SYNC_TRANSFER_START parameter which doesn't
apply when the axi_dmac is configured for the tx path.
2018-08-20 14:29:57 +03:00
74a24c4edd
fmcomms2/common: Use DDS cordic on 14 bit atan LUT
2018-07-18 18:19:30 +03:00
7062785947
fmcomms2: Connect dac data underflow
...
DAC data underflow from the DMA, was not connected to anything. This
signal should be connected to the util_rfifo, which will forward it to
the device core.
2017-11-06 10:29:34 +00:00
cf25aeacf5
fmcomms2_bd- keep data flow format
2017-08-03 13:41:26 -04:00
bb0cdf2f5e
fmcomms2: Update IP instantiations
2017-04-21 15:09:37 +03:00
b84325d43f
fmcomms2: take into consideration both adc_r1 and dac_r1 for clock division selection
2017-01-13 13:56:04 +02:00
e77428c50e
fmcomms2: Added FIFOs for DAC and ADC paths so that the path works at l_clk / 2 or l_clk /4
...
- removed ILA
2017-01-11 18:12:35 +02:00
8e1034946f
fmcomms2/zcu102- 2016.2 updates
2016-09-30 11:55:10 -04:00
f1e787f86b
fmcomms2: TDD control is enabled by default
2016-09-16 14:45:39 +03:00
af4c43b6e1
hdl-vivado-2016.2: Update fmcomms2 and pzsdr base design
2016-08-01 13:49:12 +03:00
8d72b645ae
fmcomms2/common: Remove ila_tdd block
2016-05-09 10:28:10 +03:00
679d471d75
Merge branch 'hdl_2016_r1' into dev
...
hdl_2016_r1 contains IP core upgrades to Vivado 2015.4.2 and hdmi_tx improvements.
2016-04-19 18:05:50 +03:00
ceea7f25b2
fmcomms2: Updated common design to 2015.4
2016-03-15 15:23:20 +02:00
e381d5170c
util_tdd_sync: Update the synchronization interface
...
Simplify the synchronization interface, there is one signal line between the synchronization module and transceiver core.
2016-02-12 14:27:37 +02:00
6197a82c80
fmcomms2/common: Add the util_tdd_sync module
2015-11-11 11:07:15 +02:00
cd8b467b1e
fmcomms2: Drop explicit axi_dmac clock synchronicity configuration
...
The axi_dmac core is now capable of detecting whether its different parts
run in different clock domains or not. No need to configure it manually any
more.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-09-18 15:28:07 +02:00
510f1cfdd9
fmcomms2_zc706: Update project with the new TDD sync interface
2015-09-09 12:35:22 +03:00
a92e049e8f
fmcomms2_bd- another attempt at ila width
2015-08-27 13:17:08 -04:00
b8f9b7040d
fmcomms2- tdd ila fixes
2015-08-27 11:55:41 -04:00
6a9790484f
fmcomm2- enable/txnrx- through devif
2015-08-27 11:41:56 -04:00
2e1e0939ce
fmcomms2- dma parameters & ila cores upgrade
2015-08-26 14:12:57 -04:00
d52308f074
axi_dmac: Change parameter name 2D_TRANSFER
...
Parameter name can't start with numbers, 2D_TRANSFER was changed to DMA_2D_TRANSFER
2015-08-20 10:14:22 +03:00
57cfb7cfb1
hdl/library: Update the IP parameters
...
The following IP parameters were renamed:
PCORE_ID --> ID
PCORE_DEVTYPE --> DEVICE_TYPE
PCORE_IODELAY_GROUP --> IO_DELAY_GROUP
CH_DW --> CHANNEL_DATA_WIDTH
CH_CNT --> NUM_OF_CHANNELS
PCORE_BUFTYPE --> DEVICE_TYPE
PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE
CHID --> CHANNEL_ID
PCORE_DEVICE_TYPE --> DEVICE_TYPE
PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N
PCORE_SERDES_DDR_N --> SERDES_DDR_N
PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE
DP_DISABLE --> DATAPATH_DISABLE
PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE
C_BIG_ENDIAN --> BIG_ENDIAN
C_M_DATA_WIDTH --> MASTER_DATA_WIDTH
C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH
NUM_CHANNELS --> NUM_OF_CHANNELS
CHANNELS --> NUM_OF_CHANNELS
PCORE_4L_2L_N -->QUAD_OR_DUAL_N
C_ADDRESS_WIDTH --> ADDRESS_WIDTH
C_DATA_WIDTH --> DATA_WIDTH
C_CLKS_ASYNC --> CLKS_ASYNC
PCORE_QUAD_DUAL_N --> QUAD_DUAL_N
NUM_CS --> NUM_OF_CS
PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID
PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID
PCORE_CLK0_DIV --> CLK0_DIV
PCORE_CLK1_DIV --> CLK1_DIV
PCORE_CLKIN_PERIOD --> CLKIN_PERIOD
PCORE_VCO_DIV --> VCO_DIV
PCORE_Cr_Cb_N --> CR_CB_N
PCORE_VCO_MUL --> VCO_MUL
PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC
PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH
PCORE_ADDR_WIDTH --> ADDRESS_WIDTH
DADATA_WIDTH --> DATA_WIDTH
NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS
DEBOUNCER_LEN --> DEBOUNCER_LENGTH
ADDR_WIDTH --> ADDRESS_WIDTH
C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED
Cr_Cb_N --> CR_CB_N
ADDATA_WIDTH --> ADC_DATA_WIDTH
BUFTYPE --> DEVICE_TYPE
NUM_BITS --> NUM_OF_BITS
WIDTH_A --> A_DATA_WIDTH
WIDTH_B --> B_DATA_WIDTH
CH_OCNT --> NUM_OF_CHANNELS_O
M_CNT --> NUM_OF_CHANNELS_M
P_CNT --> NUM_OF_CHANNELS_P
CH_ICNT --> NUM_OF_CHANNELS_I
CH_MCNT --> NUM_OF_CHANNELS_M
4L_2L_N --> QUAD_OR_DUAL_N
SPI_CLK_ASYNC --> ASYNC_SPI_CLK
MMCM_BUFIO_N --> MMCM_OR_BUFIO_N
SERDES_DDR_N --> SERDES_OR_DDR_N
CLK_ASYNC --> ASYNC_CLK
CLKS_ASYNC --> ASYNC_CLK
SERDES --> SERDES_OR_DDR_N
GTH_GTX_N --> GTH_OR_GTX_N
IF_TYPE --> DDR_OR_SDR_N
PARALLEL_WIDTH --> DATA_WIDTH
ADD_SUB --> ADD_OR_SUB_N
A_WIDTH --> A_DATA_WIDTH
CONST_VALUE --> B_DATA_VALUE
IO_BASEADDR --> BASE_ADDRESS
IO_WIDTH --> DATA_WIDTH
QUAD_DUAL_N --> QUAD_OR_DUAL_N
AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT
ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH
ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH
MODE_OF_ENABLE --> CONTROL_TYPE
CONTROL_TYPE --> LEVEL_OR_PULSE_N
IQSEL --> Q_OR_I_N
MMCM --> MMCM_OR_BUFR_N
2015-08-19 14:11:47 +03:00
10d9de39a1
axi_ad9361/tdd: Update the synchronization logic
...
The master will regenerate a sync pulse periodically. The period can be defined by software.
2015-08-19 12:21:23 +03:00
bcee3e04d4
fmcomms2_tdd: Update tdd_enabaled path
...
This line controls the mux, which switch between hdl and software (GPIO) control of the ENABLE/TXNRX pins.
Fix the broken path and change the name from "tdd_enable" to "tdd_enabled".
2015-08-19 12:14:05 +03:00
d2c99acae8
fmcomms2/TDD: Update synchronization interface
...
Synchronization is done by a simple req/ack interface between a master and slave terminal.
2015-08-06 15:14:36 +03:00
8e631e56d6
fmcomms2: Add a synchronization interface for TDD mode.
...
Supported carrier are ZC706 and RFSOM.
The synchronization pulse is automatically generated by the master terminal, when TDD mode is enabled.
By default a terminal is slave, software must write 0x01 into TDD register 0x50.
2015-07-28 14:42:54 +03:00
0102e3e02c
fmcomms2_ALL: Preserve backward compatibility for ENABLE/TXNRX control
...
By default the ENABLE/TXNRX pins are controlled by GPIOs, if the TDD module is enabled, the TDD FSM will take over the control of these two pins.
2015-07-01 13:54:01 +03:00
6862655b0d
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-06-26 11:07:10 +02:00
f1e75963a2
fmcomms2: wfifo+pack changes
2015-06-05 09:20:50 -04:00
3b1ea7e528
axi_ad9361/tdd: Cherry picked commit 598ece4 from hdl_2015_r1 branch
...
598ece4c8d
2015-06-04 18:09:47 +03:00
3e51d29f75
enable/txnrx- tdd changes
2015-05-18 14:28:20 -04:00
d9a124b767
fmcomms2_zc706: TDD integration, initial commit.
2015-05-11 12:20:45 +03:00
a8d4c916c1
fmcomms2_bd: remove axi3 switch
2015-05-01 11:47:29 -04:00
3fd830b038
fmcomms2: Use AXI3 interface for the DMA on ZYNQ
...
On ZYNQ the HP interconnects have a AXI3 interface. The DMA controller
supports both AXI4 and AXI3. By switching to AXI3 there is no need to create
a protocol converter between the DMA and the HP port.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-17 19:51:37 +02:00
71d4f3a474
fmcomms2: Don't mark synchronous paths as asynchronous for the DMAs
...
The AXI master interface and the register map AXI slave interface use the
same clock. No need to mark the interfaces as asynchronous. This removes the
need for CDC logic on those paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-17 19:51:37 +02:00
7bdce3837e
fmcomms2: Update interrupts
...
The new interrupts connections are made inside IPI by the process called 'ad_cpu_interrupt'.
2015-03-16 19:13:45 +02:00
9e57e919c4
fmcomms2: spi/gpio moved to base design
2015-03-10 15:26:57 -04:00
b9e2c5659f
fmcomms2: 2014.4
2015-01-09 14:12:54 -05:00
19c2da836c
rfsom: updated to rfsom
2014-12-23 14:03:59 -05:00
8e41af7b92
fmcomms2: 2014.4 update
2014-12-23 14:03:54 -05:00
7e2a9ce569
fmcomms2: Updated base design interrupt system for microblaze
2014-11-07 13:54:43 +02:00
6fac294b6f
fmcomms2: Updated zc706 project to new interrupt system
2014-10-31 14:15:29 +02:00
d04a545a41
fmcomms2: updated zc706 project with new constraint style
2014-10-27 19:27:36 +02:00
17675863e0
all_projects: Fix the interrupt connections to preserve IRQ layout
2014-10-22 11:48:08 +03:00
f528873fa9
fmcomms2: Add an additional SPI interface for up/down converter board
...
Supported carriers are: ZC706, ZC702 and Zed.
2014-10-10 18:47:07 +03:00
fe8a076b2e
fmcomms2: Cosmetic changes on *_bd.tcl script
2014-10-10 17:06:32 +03:00
7a9e694446
fmcomms2: Connect DMA directly to the HP ports
...
The DMA controller is able to send AXI3 compatible requests, no need to add
a interconnect for protocol conversion in between the DMA controller and the
HP port.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-10 16:25:14 +03:00
87047fd83e
fmcomms2: Set dac_unpack channels to 4
...
There are only 4 DAC channels in the fmcomms2 design, so set the number of
channels of the dac_unpack core to 4. This slightly reduces resource usage
as well as reducing the DMA alignment requirement from 128bit to 64bit. The
later value is what existing applications expect the alignement requirement
to be.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-10 16:25:06 +03:00
Lars-Peter Clausen
AndreiGrozav
Istvan Csomortani
Rejeesh Kutty
Adrian Costina