Drive all output pins of the disabled interfaces with a constant value.
This avoids warnings from the tools about not driven output ports.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Mark all unused output ports explicitly as explicitly. This makes it clear
that they are left unconnected on purpose and avoids warnings from the
tools about unconnected ports.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
For the source controller use the pause signal that has been properly
transferred to the source clock domain rather than the pause signal from
the request clock domain.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This control signal can be overwritten by the up_axis_xlast/up_axis_xlast_en bits, in order to create a single stream, which is contains multiple streams.
This can be use to fill up the DACFIFO module.
While the reset for the memory mapped AXI master is synchronous to some
clock it is not necessarily synchronous to the clock used for that
interface. So always generate a local reset signal to avoid problems that
could result from this.
While we are at it also update the code to only generate a local reset if
the interface is asynchronous to the register map, otherwise use the
register map reset.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The src_response_fifo has been removed from the design, but we still need to
assert the ready and empty control signals for things to work properly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the FPGA internal control signals are active high, using a active low
reset inserts a extra invert LUT. By using a active high reset we can avoid
that.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Instead of just marking all clock domains as asynchronous set the
appropriate constraints for each CDC path.
For single-bit synchronizers use set_false_path to not constraint the path
at at all.
For multi-bit synchronizers as used for gray counters use set_max_delay with
the source clock period domain to make sure that the signal skew will not
exceed one clock period. Otherwise one bit might overtake another and the
synchronizer no longer works correctly.
For multi-bit synchronizers implemented with hold registers use
set_max_delay with the target clock period to make sure that the skew does
not get to large, otherwise we might violate setup and hold time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Bring back the AXIS FIFO as a separate module instead of embedding it into
the DMAC module. This makes it possible to use it in other modules outside
of the DMAC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Move the axi_repack block to its own module. This allows it to use it
outside of the DMA controller.
Also rename it to util_axis_resize to better reflect its function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
When the DMA controller gets disabled in the middle of a transfer it is
possible that the resize block contains a partial sample. Starting the next
transfer the partial sample will appear the begining of the new stream and
also cause a channel shift.
To avoid this make sure to reset and flush the resize blocks when the DMA
controller is disabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
We need to make sure to not prematurely de-assert the s_valid signal for the
request splitter when disabling the DMAC. Otherwise it is possible that
under certain conditions the DMAC is disabled with a partially accepted
request and when it is enabled again it will continue in an inconsistent
state which can lead to transfer corruption or pipeline stalls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All components should use the internal 'do_enable' signal instead of the
external 'enable' signal. The former correctly incorporates the shutdown
sequence and does not get asserted again until the shutdown has been
completed. Using the external signal can cause problems when it is disabled
and enabled again in close proximity.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Vivado 2014.4 is too greedy, when it needs to optimize. See more about the issue here: https://ez.analog.com/thread/48214
The response_dest_resp is unused, so not save to concatenate with a valid signal like the eot.
Make sure that the address generator behaves correctly when the buswidth is not
64-bit. Also since the source and destination can have different widths add
separate parameters for source and destination address alignment.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
There were a few place in the core where it assumed a 64-bit wide bus. Make this
configurable using parameters. The patch also adds support for having different
DMA bus widths on the source and destination side.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Lars-Peter Clausen
Istvan Csomortani
Rejeesh Kutty
Adrian Costina