The up_rstn is driven by s_axi_resetn, which is generated by a
Processor System Reset module. (connected to port peripheral_aresetn)
Therefor using this reset signal as an asynchronous reset is redundant,
and a bad design practice at the same time. Asynchronous reset should be
used if it's inevitable.
The external s_axi_{awaddr,araddr} signals that are connect to the core
have their width set according to the specified size of the register map.
If the s_axi_{awaddr,araddr} signal of the core is wider (as it currently
is for many cores) the MSBs of those signals are left unconnected, which
generates a warning.
To avoid this make sure that the signal width matches the declared register
map size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
Not all peripherals need the full address space. To be able to infer the
size of the address space of a peripheral allow the size of the AXI address
signals to be configurable rather than hardcoding its width to 32 bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The Qsys interconnect does not handle the assertion of BVALID on the
same cycle as [A]WREADY. Add a single cycle of delay to prevent
deadlocks.
Similar to:
2817ccdb22
("up_axi: altera can not handle same clock assertion of arready and rvalid")
Signed-off-by: Matthew Fornero <matt.fornero@mathworks.com>
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This is unused and unneeded. The AXI interconnect will make sure that a
peripheral only gets requests that are meant for it, there is no need to
check the address in the peripheral itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Make sure that if a read and a write request arrive on the very same clock
cycle to only accept one of them. The simple solution chosen here is to only
accept the write request when this happens and delay the acceptance of the
read request until the write request is finished.
This solution is not fair since a write request will always take precedence,
which in theory allows the write bus to starve the read bus. But in practice
we should never see that many write requests that we are unable to answer
the read request.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Wait for the master to accept the response for the current transaction
before we allow a new transaction to start.
This fixes problems in case the master is not ready to accept the response
when we make it available.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Arpadi
Edward Kigwana
Istvan Csomortani
Lars-Peter Clausen
Rejeesh Kutty
Matthew Fornero