Add CMOS support for the interface for the following symbol modes on Xilinx devices:
A B C D E F G H
CSSI__1-lane 1 16/8 80(SDR)/160(DDR) 80 - SDR/DDR SDR/DDR->4/2(C=16), 2/1(C=8)
Columns description:
A - SSI Modes
B - Data Lanes Per Channel
C - Serialization factor Per data lane
D - Max data lane rate(MHz)
E - Max Clock rate (MHz)
F - Max Sample Rate for I/Q (MHz)
G - Data Type
H - DDS Rate
CSSI - CMOS Source Synchronous Interface
If R1 mode is first syncronized to the dac clock domain will prevent its
usage if the dac clock is missing. In such case the synchronization will not
propagate.
De-assert dac_rst together with an updated control set.
This allows writing the control registers before releasing the reset.
This is important at start-up when stable set of controls is required.
The external synchronization signal should be synchronous with the
dac clock. Synchronization will be done on the rising edge of the signal.
The control bit is self clearing. Status bit shows that the synchronization
is armed but the synchronization signal has not yet been received
Added EXT_SYNC parameter to be able to keep the dac_sync original
behavior
Common basic steps:
- Include/create infrastructure:
* Intel:
- require quartus::device package
- set_module_property VALIDATION_CALLBACK info_param_validate
* Xilinx
- add bd.tcl, containing init{} procedure. The init procedure will be
called when the IP will be instantiated into the block design.
- add to the xilinx_blockdiagram file group the bd.tcl and common_bd.tcl
- create GUI files
- add parameters in *_ip.tcl and *_hw.tcl (adi_add_auto_fpga_spec_params)
- add/propagate the info parameters through the IP verilog files
axi_clkgen
util_adxcvr
ad_ip_jesd204_tpl_adc
ad_ip_jesd204_tpl_dac
axi_ad5766
axi_ad6676
axi_ad9122
axi_ad9144
axi_ad9152
axi_ad9162
axi_ad9250
axi_ad9265
axi_ad9680
axi_ad9361
axi_ad9371
axi_adrv9009
axi_ad9739a
axi_ad9434
axi_ad9467
axi_ad9684
axi_ad9963
axi_ad9625
axi_ad9671
axi_hdmi_tx
axi_fmcadc5_sync
The DAC DMA will never overflow and unsurprisingly the dac_dovf signal is
never used anywhere. It is very unlikely it will ever be used, so remove
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
+ Add a HDL parameter for the PPS receiver module :
PPS_RECEIVER_ENABLE. By default the module is disabled.
+ Add the CMOS_OR_LVDS_N and PPS_RECEIVER_ENABLE into the CONFIG
register
+ Define a pps_status read only register, which will be asserted, if the free
running counter reach a certain fixed threshold. (2^28) The register can
be deasserted by an incomming PPS only.
The ad_pps_receiver is instantiated at the top of core.
The rcounter is placed into adc/dac_common registers space, at the
address 0x30 (word aligned).
The interrupt mask is placed into adc/dac_common, at the address 0x04
(word aligned). Because the core has an instance of both modules, the
interrupt masks are OR-ed together.
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
In case of high precision devices with just a simple SPI interface
for control and data, the effective data rate can be significatly
lower than the SPI clock, and more importantly there isn't any relation
between the two clock domain.
The rate is defined by a SOT (start of transfer) generator, which
initiates a SPI transfer. Taking the fact that the generator runs
on system clock (100 MHz), and the device can require smaller rate (in kHz domain),
the 7 bit dac_datarate register is just too small.
Therefor increasing to 16 bit.
Not all peripherals use the GPIO register settings, but the registers still
take up a fair amount of space in the register map. Add options to allow to
disable them when not needed. This helps to reduce the utilization for
peripherals where these features are not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Linuxe drivers are checking the drp_locked status even if the
core does not contains a clock generation/managment module. To
not break all the designs, revert all the status and control bits to
there old locations.
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
alin724
Laszlo Nagy
Adrian Costina
stefan.raus
AndreiGrozav
Istvan Csomortani
Lars-Peter Clausen
Rejeesh Kutty
Shrutika Redkar