The goal of this commit is to make sure there isn't any significance to
the order in which parameters of ad_connect are specified.
As an example, previously you could only `ad_connect target VCC`, while
`ad_connect VCC target` would fail.
Note: This code intentionally ignores bd_{,intf_}ports, because
these can all be treated as bd_pins.
Signed-off-by: David Winter <david.winter@analog.com>
For fixing "Failed to reset the device and set SPI Config"
error, both clockPolarity and clockPhase should be disabled
or both enabled. By default both are unset.
Signed-off-by: Stefan Raus <stefan.raus@analog.com>
This commit fixes the 16.5Gbps lane rate case where the link drops
after few seconds an initial successful link up happens.
A few seconds delayed calibration process can workaround this but with
having the differential drivers swing increased this is no longer
required.
This will allow building base test harnesses and place on top of them
existing block designs for simulation purposes.
Test harnesses will contain basic functionality like
- clock and reset generators
- AXI master to aid register access of the cores.
- memory model of the DDR
- interrupt controller
Existing procedures (ad_mem_hp0_interconnect, ad_cpu_interconnect, ... ) will
connect to this harness as they do to a real base design.
To support deterministic latency with non-power of two octets per frame
(F=3,6) the interface width towards the transport layer must be resized
to match integer multiple of frames.
e.g Input datapath width = 4; Output datpath width = 6;
for F=3 one beat contains 2 frames
for F=6 one beat contains 1 frame
The width change is realized with a gearbox.
Due the interface width change the single clock domain core is split
in two clock domains.
- Link clock : lane rate / 40 for input datapath width of 4 octets 8b10b
- lane rate / 20 for input datapath width of 8 octets 8b10b
- lane rate / 66 for input datapath width of 8 octets 64b66b
- Device clock : Link clock * input data path width / output datapath width
Interface to transport layer and SYSREF handling is moved to device clock domain.
The configuration interface reflects the dual clock domain.
If Input and Output datapath width matches, the gearbox is no longer
required, a single clock can be connected to both clocks.
In most of the standalone projects the generic project creation flow is not followed. The project's device
is defined manualy. This fix makes sure that those projects still builds without an issue.
NOTE: In these case we should use adi_project_create directly in system_project.tcl.
Without defining this signal, the UART lines receive garbage data
when no cable is connected to the J4 USB UART port.
The GPIO9 is enabled in the reference base design along with the
4MA CURRENT_STRENGTH constraint on the UART pins
When phase alignment is active, the PFD frequency value should be used
as outclk1 actual frequency.
The configuration interface of the fPLL does not support fractional values.
If the reference clock is fractional, the tool will throw an error that requirement
above is not respected.
Round up the reference clock for the SERDES and the lane rate in order to
overcome this issue, until it's not fixed by Intel.
When phase alignment is active, the PFD frequency value should be used
as outclk1 actual frequency.
The configuration interface of the fPLL does not support fractional values.
If the reference clock is fractional, the tool will throw an error that requirement
above is not respected.
Round up the reference clock for the SERDES and the lane rate in order to
overcome this issue, until it's not fixed by Intel.
When phase alignment is active, the PFD frequency value should be used
as outclk1 actual frequency.
The configuration interface of the fPLL does not support fractional values.
If the reference clock is fractional, the tool will throw an error that requirement
above is not respected.
Round up the reference clock for the SERDES and the lane rate in order to
overcome this issue, until it's not fixed by Intel.
-change the video memory interfacing from f2h_axi_slave to
f2h_sdram0
- add f2h_sdram1 port as the default interface for converter DMA
- set as default the full HD resolution at 60 FPS (pixel clock 148.5MHz)
- use a second 200MHz(198MHz) clock from the pixel_clk_pll, as DMA source
to destination clock.
Laszlo Nagy
David Winter
stefan.raus
sergiu arpadi
Owen McAree
vladimirnesterov
Adrian Costina
Istvan Csomortani
aholtzma
AndreiGrozav
IMoldovan