* Added header license for the files that didn't have
* Modified parentheses
* Removed extra spaces at the end of lines
* Fixed parameters list to be each parameter on its line
* Deleted lines after endmodule and consecutive empty lines
* Fixed indentation
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
Add parameter that describes interface to link layer, this must be
integer multiple of octets per frame.
Add parameter that describes interface to user/DMA, this must be
multiple of bytes so software can process the samples easier.
To support deterministic latency with non-power of two octets per frame
(F=3,6) the interface width towards the transport layer must be resized
to match integer multiple of frames.
e.g Input datapath width = 4; Output datpath width = 6;
for F=3 one beat contains 2 frames
for F=6 one beat contains 1 frame
The width change is realized with a gearbox.
Due the interface width change the single clock domain core is split
in two clock domains.
- Link clock : lane rate / 40 for input datapath width of 4 octets 8b10b
- lane rate / 20 for input datapath width of 8 octets 8b10b
- lane rate / 66 for input datapath width of 8 octets 64b66b
- Device clock : Link clock * input data path width / output datapath width
Interface to transport layer and SYSREF handling is moved to device clock domain.
The configuration interface reflects the dual clock domain.
If Input and Output datapath width matches, the gearbox is no longer
required, a single clock can be connected to both clocks.
The external synchronization signal should be synchronous with the
adc clock. Synchronization will be done on the rising edge of the signal.
The control bit is self clearing. Status bit shows that the synchronization
is armed but the synchronization signal has not yet been received. While
the synchronization mechanism is armed, the adc_rst output signal is set
The current format should allow for the SYSREF signal to be used as
synchronous capture start, but will need to be disabled before the
synchronization mechanism is armed
Common basic steps:
- Include/create infrastructure:
* Intel:
- require quartus::device package
- set_module_property VALIDATION_CALLBACK info_param_validate
* Xilinx
- add bd.tcl, containing init{} procedure. The init procedure will be
called when the IP will be instantiated into the block design.
- add to the xilinx_blockdiagram file group the bd.tcl and common_bd.tcl
- create GUI files
- add parameters in *_ip.tcl and *_hw.tcl (adi_add_auto_fpga_spec_params)
- add/propagate the info parameters through the IP verilog files
axi_clkgen
util_adxcvr
ad_ip_jesd204_tpl_adc
ad_ip_jesd204_tpl_dac
axi_ad5766
axi_ad6676
axi_ad9122
axi_ad9144
axi_ad9152
axi_ad9162
axi_ad9250
axi_ad9265
axi_ad9680
axi_ad9361
axi_ad9371
axi_adrv9009
axi_ad9739a
axi_ad9434
axi_ad9467
axi_ad9684
axi_ad9963
axi_ad9625
axi_ad9671
axi_hdmi_tx
axi_fmcadc5_sync
Add support for 8 bit resolution for the transport layer.
Fix parameter BITS_PER_SAMPLES propagation to all the internal modules, in
several cases this variable was hard coded to 16.
Registers from this component can fit in the 2k address range.
Since Vivado's minimal address range is 4k, use that instead.
This will allow placing the independent TPLs to base addresses
that mach the addresses from the monolithic blocks ensuring no software
intervention.
Iulia Moldovan
AndreiGrozav
alin724
PopPaul2021
Laszlo Nagy
Iacob_Liviu
Filip Gherman
Dan Hotoleanu
Adrian Costina
Istvan Csomortani
stefan.raus
Arpadi