This commit reverts part of the changes done in the following commit:
- ff50963c7f -
"axi_ad9361- altera/xilinx reconcile- may be broken- do not use"
The above mentioned commit introduced latency variations on the Rx path
at different sample rates, or within the same sample rate after sample
rate changes. The variation is caused by multiple positions of the frame
detection combined with a free running toggle (rx_valid) that is not synchronized
with the actual samples.
Having a single frame detection position eliminates the latency
variation.
When having multiple 936x in parallel, this change enables the use of source
synchronous received clock from the master as sampling clock for other slaves.
This will eliminate skew between the interfaces since the data delays
are going to be tuned against the master clock after a multi-chip
synchronization (MCS) is done. This eliminates the clock crossing from
the slave to master domain inside the FPGA.
Define a MIMO_ENABLE parameter for the core, which will insert
and additional de-skew logic to prevent timing issues coming from
the clock skew differences of two or multiple AD9361.
Common basic steps:
- Include/create infrastructure:
* Intel:
- require quartus::device package
- set_module_property VALIDATION_CALLBACK info_param_validate
* Xilinx
- add bd.tcl, containing init{} procedure. The init procedure will be
called when the IP will be instantiated into the block design.
- add to the xilinx_blockdiagram file group the bd.tcl and common_bd.tcl
- create GUI files
- add parameters in *_ip.tcl and *_hw.tcl (adi_add_auto_fpga_spec_params)
- add/propagate the info parameters through the IP verilog files
axi_clkgen
util_adxcvr
ad_ip_jesd204_tpl_adc
ad_ip_jesd204_tpl_dac
axi_ad5766
axi_ad6676
axi_ad9122
axi_ad9144
axi_ad9152
axi_ad9162
axi_ad9250
axi_ad9265
axi_ad9680
axi_ad9361
axi_ad9371
axi_adrv9009
axi_ad9739a
axi_ad9434
axi_ad9467
axi_ad9684
axi_ad9963
axi_ad9625
axi_ad9671
axi_hdmi_tx
axi_fmcadc5_sync
Commit ff50963c7f ("axi_ad9361- altera/xilinx reconcile- may be broken-
do not use") inverted the polarity of the TX feedback clock.
This exposed some issues in the existing drivers which can cause the
interface tuning to fail randomly under certain conditions.
To keep backwards compatibility with existing drivers restore the previous
behavior.
A separate fix will be applied to the drivers that resolves the issue that
has been exposed by the polarity inversion. So that interface calibration
works reliably under all conditions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
Laszlo Nagy
Istvan Csomortani
AndreiGrozav
Lars-Peter Clausen
Rejeesh Kutty