f2cd7626f5
adi_project : ZC706 board name changed on 2014.2
2014-09-22 17:33:49 +03:00
fb5d212370
daq2/kcu105: fixed timing violations
2014-09-19 15:55:42 -04:00
751bdd6cfc
daq1: Update the constraint file
...
- tx_ref_clk and rx_sysref need to be differential
- cosmetic changes
2014-09-19 18:22:57 +03:00
f43b5d707e
fmcomms2: Reduced clock frequency for ILA to meet timing for ZED
...
Modified ZED constraints to 250 MHz for the clock from AD9361
2014-09-16 16:08:28 -04:00
d33fb07587
usdrx1: Modified the GPIO assignments so that board specific GPIOs start from GPIO 32.
...
GPIOs for which the directions is known, have been specifically assigned.
The SPI clock has been changed to a lower frequency.
2014-09-16 15:56:19 -04:00
d4db53c3b0
usdrx1_spi: Modified module to be compatible with altera
2014-09-16 15:53:11 -04:00
a3dbd5ac00
projects/common/vc707/vc707_system_bd: AD9625_FMC update to 2014.2
...
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
2014-09-16 14:59:36 +02:00
a91f4bb6b9
daq1: General updates
...
- Add additional GT setups
- Use channel PLL instead of quad PLL
- Add additional ILA probes for debug
2014-09-13 00:23:11 +03:00
d8651cdd2e
fmcomms2: c5soc: Set dac_util_unpack number of channels to 4
...
We only do have 4 channels in this design. Reducing the number of supported
channels for the dac_util_unpack core to 4 from 8 lowers the DMA alignment
requirement from 128bit to 64bit. We need this since applications only
expect a DMA alignment requirement of 64bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-12 16:15:12 +02:00
ecc498313c
fmcomms2: c5soc: Connect ADC, DAC and VGA DMA to different bridge interconnects
...
We have enough bridge interconnect to give each DMA its own, so use them.
This makes sure that they do not interfere with each others transfers to
much. The SDRAM controller side of the FPGA2SDRAM bridges FIFO runs at a
much faster frequency then what we are able to use in the fabric. So its
better to do the arbitration on that side of the bus to make sure that we
can utilize the buses in the FPGA fabric to the maximum for each DMA core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-12 16:14:07 +02:00
61f21a17b3
fmcomms2:c5soc project upgraded with util_dac_unpack
2014-09-11 15:13:09 -04:00
4c1c50788e
fmcomms5: c5soc: Fix typo
...
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-11 17:15:10 +02:00
41cc92ef49
Remove BASEADDR/HIGHADDR parameters
...
This is unused and unneeded. The AXI interconnect will make sure that a
peripheral only gets requests that are meant for it, there is no need to
check the address in the peripheral itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-11 12:26:37 +02:00
647a26e19c
projects/common/vc707/vc707_system_bd.tcl: Select Linux MMU settings
2014-09-10 17:40:36 +02:00
c7989925c5
fmcomms2: c5soc: Add false path between 50MHz and VGA PLL clock
...
Otherwise we get timing errors for the reset signal that is generated in the
50MHz clock domain, but used in the VGA PLL clock domain.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-09 15:05:06 +02:00
328205c31d
fmcomms2: c5soc: Set DMA transfer length to 24 bits
...
14 bits is a bit to low and we use 24 bits everywhere else as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-09 15:05:06 +02:00
50faf0c53a
Remove executable flags from non-exectuable files
2014-09-09 15:05:06 +02:00
b58e425b44
daq2/kcu105: timing improvement -register slices hang
2014-09-08 10:24:56 -04:00
6e389b8c47
motor_control: Updated the FOC IP and the encoder connections to the IP
2014-09-06 15:58:03 +03:00
669462e0f6
ad9625x2: updates on pcores
2014-09-05 12:25:43 -04:00
72f31370ef
a5gt: ethernet-fpga lvds mode
2014-09-04 11:19:25 -04:00
3deb55bb98
a5gt: ethernet i/o changed to lvds
2014-09-04 11:19:24 -04:00
dfb94f7b68
motor_control: Modified foc_controller to be compatible with other cores
2014-09-03 12:09:37 +03:00
9f3461b130
fmcjesdadc1: Added support for KC705
2014-09-02 18:02:25 +03:00
17122661d2
fmcomms2_pr: Fix file path on ZC706/system_bd.tcl
2014-09-01 18:49:55 +03:00
2ce7695bf7
fmcjesdadc1: Initial commit of VC707 version
2014-09-01 18:47:01 +03:00
9a80fec4e4
fmcjesdadc1: Delete trailing whitespaces
2014-09-01 18:45:20 +03:00
d08d0cd70b
motor_control: added the MW FOC IP and updated the design
2014-09-01 18:35:21 +03:00
ee752ec08a
daq1: Initial commit
2014-09-01 18:34:31 +03:00
a773cc4992
usdrx1: updated project
...
ad_jesd_align wasa updated to be able to work with frames that have more than 4 octets per frame
2014-09-01 15:18:39 +03:00
95c143412d
fmcomms2: Modified design to work with 4 channel util_adc_pack
2014-08-29 13:53:59 +03:00
da913864c9
ad9671_fmc: updates to match recent core changes
2014-08-28 13:16:52 -04:00
5a42c10233
projects/fmcomms2/c5soc: Added video output. HPS SPI was replaced by 3 Wire SPI.
2014-08-27 21:46:23 +03:00
c435edf194
ad9652/zc706: fix dma write
2014-08-27 10:44:39 -04:00
7b280b3bbf
fmcomms6: zc706 build-only version
2014-08-27 10:44:37 -04:00
0e909647b4
fmcomms6: initial checkin
2014-08-27 10:44:36 -04:00
a49eb5853b
ZED, ZC702: Added contraints so that projects can successfully synthesize on linux systems
...
For ZC706 Fixed one constraint which was not correct
2014-08-26 16:28:41 +03:00
5f21f54463
fmcjesdadc1: zc706 version
2014-08-25 14:28:57 -04:00
cb29b83b05
a5gt: updates to match a5gt
2014-08-25 10:46:59 -04:00
76ffb939e5
zc706: ad9625 copy
2014-08-22 11:24:24 -04:00
fe1eaefcff
fmcomms1: zc706
2014-08-22 09:08:55 -04:00
280260e54c
c5soc: dmac separated slave and master id widths
2014-08-22 09:08:54 -04:00
f3f8414d81
kcu105: changes for ad_iobuf
2014-08-15 15:01:52 -04:00
b481df0b5f
library: local constraints async groups
2014-08-14 15:09:51 -04:00
39bb7ca231
a5soc: fmcjesdadc1+hdmi version
2014-08-14 09:05:38 -04:00
a54e4edb08
Add xfest14 PMODs project
...
This project has a SPI controller connected to each of the ZED boards PMOD
ports JA, JB, JC, JD pin 1-4. Pin 7-10 are connected to the PS7 general purpose
GPIOs, except for JC where it is connected to the PS7 UART controller.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-08-12 10:14:16 +02:00
96969079ce
a5soc: fixes for 14.0 and spi conflicts
2014-08-11 16:46:37 -04:00
902d5b0da2
prcfg: Update fmcomms2_pr for ZC706
2014-08-05 17:55:31 +03:00
9dfbf4a9a6
prcfg: Update the prcfg logic to the new ad9361 interface
2014-08-05 17:54:37 +03:00
e9f8c0fb5f
fmcomms5: ZC706 modified constraints for linux build machines
2014-08-01 18:09:55 +03:00
6c6cab0e16
fmcomms2: ZC706 modified constraints for linux build machines
...
The added constraints allow the project to successfully pass timing on some ubuntu or debian build machines.
2014-08-01 17:34:36 +03:00
663588eeaf
daq2/kcu105: working ddr version
2014-07-29 09:15:30 -04:00
9cdd4107cd
fmcomms5: ZC702: add reset_b and fixed system_top
2014-07-25 15:24:11 +03:00
7bee85423d
c5soc: removed stp/cdf files
2014-07-24 20:53:08 -04:00
59759a8ab3
c5soc: working hdl version
2014-07-24 20:51:41 -04:00
7000897031
fmcomms2, fmcomms5: updated util_adc_pack and util_dac_unpack
...
The cores now support up to 8 channels, in 1, 2, 4, 8 channel active configuration
2014-07-24 19:57:22 +03:00
a68f634de9
fmcomms5: Added resetb for the second AD9361
2014-07-24 17:31:30 +03:00
49a77c0413
prcfg: Generate configuration files to *.bin
2014-07-24 09:43:00 +03:00
db2386a351
daq2/kcu105: latest mig updates
2014-07-23 16:25:55 -04:00
db1c931736
ad9625_plddr: PL DDR3 fixes
...
- Modified the axi slave interface handler
- Increased the rfifo_mem input depth to prevent overflow
2014-07-23 19:34:44 +03:00
4da8100fe5
ad9625_plddr: Delete trailing whitespaces.
2014-07-23 19:31:07 +03:00
c0e31aa6c2
daq2: latest hardware
2014-07-21 09:06:57 -04:00
e3320c43cb
fmcomms2/c5soc: programmer file
2014-07-21 09:06:55 -04:00
9b9e0c6a56
fmcomms2/c5soc: signal tap
2014-07-21 09:06:54 -04:00
65879d621f
daq2: updates for the new hardware
2014-07-21 09:06:53 -04:00
2b6ce1e504
zc706_plddr3 : Fix axi_fifo2s_axi_mrst net
2014-07-21 15:10:36 +03:00
2955b9db78
fifo2s: flush if no request, c5soc: 14.0
2014-07-15 16:25:33 -04:00
e7d5d79e42
daq2/kcu105: gth up and running - as it is commit
2014-07-10 10:56:37 -04:00
085512a738
fmcomms2_pr: Fix the source path for prcfg_setup
2014-07-10 17:54:41 +03:00
95701fbd0e
fmcomms2_pr : PR initial check in
2014-07-10 10:41:48 +03:00
b434fe6dd5
fmcomms5: register map changes
2014-07-08 16:57:43 -04:00
39ac29bb01
AD9361: Altera, modified address width so that all registers are accessible
...
Modified qsys project with the new address span
2014-07-08 10:41:51 +03:00
10c21a343a
fmcomms2/c5soc: Fixed the spim0_ss_in_n value.
2014-07-08 10:07:31 +03:00
c53b257ab1
fmcomms2/c5soc: Fixed the MOSI and MISO pin assignments.
2014-07-07 22:28:25 +03:00
c75e6b3043
kcu105 pwr-good removed
2014-07-07 09:56:13 -04:00
f2bf5ced04
ad9625: register map updates
2014-07-03 14:30:03 -04:00
f94cbbb0aa
daq2: register map updates
2014-07-03 12:36:37 -04:00
a388ccab0a
fmcomms2/c5soc: initial checkin
2014-07-02 14:56:00 -04:00
9a08189b93
c5soc: initial a5soc copy
2014-07-01 13:09:38 -04:00
c1b7fc17f5
c5soc: initial a5soc copy
2014-07-01 13:05:26 -04:00
60dd14bcdb
a5soc: removed jtag master control
2014-07-01 12:27:37 -04:00
ba7955c531
fmcomms2: register map modifications
2014-06-26 10:09:03 -04:00
92e525d573
ad9250: register map updates
2014-06-25 15:24:48 -04:00
e38813fa9f
fifo- monitor status signals
2014-06-25 12:15:13 -04:00
57bb3705f2
zc706-plddr3: read changes to lower dma clock
2014-06-25 09:20:58 -04:00
3d8d576532
prcfg_script: Update the PR flow script
...
+ Make part global
+ No need the Explore directive on implementation
+ Fix some reference to pr module
+ Fix the pr_verify function
2014-06-13 20:33:59 +03:00
7efd6149f8
daq2: initial checkin
2014-06-12 15:54:25 -04:00
b1b9067512
ad9625x2_fmc: added multi-sync support
2014-06-12 15:45:35 -04:00
6ea7dd7fc3
kcu105: pwr-good added
2014-06-12 15:22:31 -04:00
6e444559b5
usdrx1: global clock fix
2014-06-10 18:09:49 +03:00
2d27f88588
ad9625_fmc, ad9625x2_fmc: initial checkin
2014-06-09 16:40:48 -04:00
bef6a9c32c
axi_ad9361: Split dma data into individual channels for both ADC and DAC
2014-06-07 17:15:31 +03:00
2837d788a6
mitx045: Added I2S core to the base design
2014-06-06 17:53:47 +03:00
bd8d355b05
scripts: Update adi_prcfg_project.tcl
...
Define a new parameter for the prcfg_init_workspace process:
prcfg_name_list.
2014-06-06 15:00:23 +03:00
cf56a568c6
kcu105: GTH updates
2014-06-05 14:27:38 -04:00
f452e40192
scripts: Initial check in of non-project flow
...
These processes are used for projects with partial
reconfiguration. The used design flow in these cases is the
non-project (batch) design flow.
2014-06-05 14:33:27 +03:00
45325b7c0d
mitx045: minor changes in common and ADV7511 projects
2014-06-03 19:24:12 +03:00
f695a45394
global clock fix
2014-06-03 09:23:23 -04:00
f217139770
fmcomms2: added project for mini_itx, xc7z045 version
2014-06-02 14:06:10 +03:00
c52327d0c6
common,adv7511: Added mitx045 platform.
2014-06-02 11:08:03 +03:00
877b81a373
ad9625/vc707: working version
2014-05-30 15:07:23 -04:00
c789dce77e
ad9625/zc706: added pl ddr3 fifo changes
2014-05-29 12:59:29 -04:00
56ddce1e8c
dmac: create fifo interface to avoid being treated as axi control stream
2014-05-27 10:25:14 -04:00
1d53d79e25
fmcomms2/common: Fix ad9361's interface
...
Loopback the l_clk to clk. l_clk is the device sampling clock, clk is used to
synchronize the cores in case of a multiple device configuration.
2014-05-21 10:09:54 +03:00
25e4520726
fmcomms2/common: Delet trailing white spaces
2014-05-21 09:47:37 +03:00
bab90a19c2
fmcomms5/zc702: removed unused ila cores
2014-05-20 14:42:48 -04:00
7e6b4ea9d0
fmcomms5: ignore only common clock to external clocks
2014-05-19 20:38:41 -04:00
9a36075324
moved fmcomms5
2014-05-19 13:49:49 -04:00
f73819f4d4
zc706: pl ddr3 initial checkin
2014-05-13 16:19:53 -04:00
f3f8374c75
ad9671: 2lane version
2014-05-08 18:33:26 -04:00
c5b3dd3643
vc707 base : tcl update
...
- Added missing address space
- Connect the sys_audio_clkgen/reset
2014-05-08 12:30:25 +03:00
3ac1da178e
kcu105: sane except for ddr4/ethernet
2014-05-06 15:39:05 -04:00
51c0ee1e20
ml605: tcl updates
2014-05-06 09:29:21 -04:00
e7cbaca216
ml605: initial checkin
2014-05-05 11:24:12 -04:00
53af7f3c1f
ml605: initial checkin
2014-05-05 11:20:26 -04:00
4d4f66fbdd
a5soc: increase pipeline for qsys
2014-05-04 10:38:53 -04:00
b55d0d7ad1
a5soc: constraints for false paths
2014-04-30 16:14:30 -04:00
a10043c4f4
kcu105: base complete with ethernet errors
2014-04-30 14:41:43 -04:00
ef60cce15e
kcu105: added
2014-04-30 14:41:40 -04:00
be69c0c330
kcu105: initial checkin
2014-04-30 14:41:39 -04:00
9900a56fa5
kcu105: initial checkin
2014-04-30 14:41:37 -04:00
0b1ce14842
a5soc: basic hardware build
2014-04-30 12:40:27 -04:00
99d66e7580
a5soc: initial-copy version
2014-04-30 12:40:26 -04:00
681e4239df
ad9671/a5gt: subclass-0 version
2014-04-28 21:31:21 -04:00
06873aeddb
ad9671/a5gt: subclass-0 version
2014-04-28 21:31:20 -04:00
d66f256f1c
9671/a5gt: 9671-sc1 version
2014-04-28 21:31:19 -04:00
f55288ef5d
ad9671: altera - base changes
2014-04-28 21:31:18 -04:00
2e7bf190b5
initial checkin-9250 copy
2014-04-28 21:31:15 -04:00
01de117b5f
motor_control: Changed controller to PID controller. Some estetic changes
2014-04-28 17:57:51 +03:00
dfc2bba335
ad9671: updates to allow default adc setup routines
2014-04-23 16:39:28 -04:00
a1bcf345c6
ad9671: fix spi connections
2014-04-21 13:46:44 -04:00
213e852e11
motor_control: Initial commit
2014-04-18 18:57:18 +03:00
ba44ee63be
fmcomms1: modified the fmcomms1_bd.tcl to make it compatible with latest wfifo
2014-04-14 17:04:04 +03:00
179d6d601c
adi_board.tcl : Use 'global' instead of '$::'
2014-04-14 11:45:35 +03:00
38126c404c
usdrx1: spi signal definitions
2014-04-11 14:28:23 -04:00
06b28d2e24
ad9671: compile fixes
2014-04-11 14:28:22 -04:00
e92e6b2fd5
ad9671_fmc: changed for ad9671-fmc
2014-04-11 14:28:21 -04:00
72e318a247
ad9671_fmc: initial checkin
2014-04-11 14:28:20 -04:00
99ef34936f
Merge branch 'master' of https://github.com/analogdevicesinc/hdl
2014-04-11 18:14:08 +03:00
d0f04fd788
fmcomms1: Commit AC701 and VC707 projects
2014-04-11 17:35:25 +03:00
c718169f27
adi_board.tcl : Fix the address assignment command
...
A lot of cores have more than one address segments, therefor need
to filter out the segment of the axi lite interface
2014-04-11 16:14:56 +03:00
cf5b9b51fd
adi_board.tcl : Fix spi ports and hp clocks
2014-04-11 15:31:12 +03:00
37e2059fd0
adi_board.tcl : General update
...
- Split the adi_dma_interconnect to two procedure:
adi_dma_interconnect and adi_hp_assign
- Fix the adi_spi_core
- Fix the adi_interconnect_lite
2014-04-10 18:29:14 +03:00
96541f0a7f
usdrx1: zc706 updated for usdrx1
2014-04-10 11:05:13 -04:00
6f36f74eea
usdrx1: common board files
2014-04-10 11:05:11 -04:00
ac1c145a61
usdrx1: initial checkin
2014-04-10 11:05:10 -04:00
dc7b3e085c
axi_dmac: Fix issues with non 64-bit AXI masters
...
Make sure that the address generator behaves correctly when the buswidth is not
64-bit. Also since the source and destination can have different widths add
separate parameters for source and destination address alignment.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-04-10 14:54:22 +02:00
9d19145713
Merge branch 'master' of https://github.com/analogdevicesinc/hdl
2014-04-10 10:50:53 +03:00
5aac9d7288
FMCOMMS2 added sync option
...
Added signals to allow synchronisation of multiple AD9361.
2014-04-10 10:46:42 +03:00
fbfd658f0d
zc706: added pl ddr3 mig
2014-04-09 15:58:12 -04:00
e73952a694
ad9467 : initial checkin
2014-04-09 17:34:40 +03:00
5b0e37b97a
adi_project.tcl : Modify implementation strategy
...
- Change implementation strategy to Performance Explore.
At some projects, this could prevent timing issues, it not
increase the overall implementation time in a dramatic way.
2014-04-07 15:02:38 +03:00
33979fc533
fixes to improve timing - fifo for clock domain transfers
2014-04-04 13:49:53 -04:00
6a19b34a00
a5gt: added tightly coupled memory
2014-04-03 20:50:17 -04:00
04ab34c8ed
a5gt: ethernet assignments
2014-04-03 20:50:16 -04:00
12e5cc91bd
make signaltap/timing part of the flow
2014-04-03 20:50:15 -04:00
d0a8b4a63c
kc705,common: Mem_interconnect maximize performance
...
For FMCOMMS1, when both the ADC and DAC DMAs are active, the system was
unstable. With this fix, it the system seems to be stable.
2014-04-03 15:59:33 +03:00
e85153b5dd
altera hal version
2014-04-01 21:12:11 -04:00
04df908fbf
altera-fmcjesdadc1 initial checkin
2014-04-01 12:01:57 -04:00
0d678b89ed
altera a5gt fmcjesdadc1 setup
2014-04-01 11:46:37 -04:00
8deb36ce08
adi_board.tcl: All procedures works on Zynq/Microblaze
...
General patch for the integration procedures. Tested on kc705 and
zed.
2014-04-01 16:19:24 +03:00
9676146725
FMCOMMS2 AC701 Project
...
Not tested - must program Vadj on board
2014-04-01 15:35:44 +03:00
e597467447
FMCOMMS2 VC707 Project
2014-04-01 15:34:29 +03:00
814b0d72d6
Modified Reset signals for FMCOMMS2 base design
...
Made all resets the same (sys_100m_resetn)
2014-04-01 15:32:48 +03:00
fbafaa8507
MicroBlaze base system: Fix a few net names
...
Every interconnect interface net name follows the convention:
<interconnect name>_<interface name>
No changes in logic or any connection!
2014-04-01 10:40:35 +03:00
f0b8b8f6c0
FMCOMMS1: KC705 updated system_top and constraints
...
Needed to be compatible with the latest common file
2014-03-31 17:49:10 +03:00
14b82c03dd
FMCOMMS1: Several modifications in the base design
...
Corrected the ADC/DAC interrupt location for microblaze systems
Removed the ILA clock generation from sys_audio_clkgen and created a
separate clock generator
All system is reset from the same source
2014-03-31 17:44:57 +03:00
a881557645
base_design: Fixed AC701 and VC707 contstraints
...
AC701: Modified the IOSTANDARD for some of the pins to correspond to the
AC701 user guide.
VC707: Fixed naming for some system clocks
2014-03-31 17:38:20 +03:00
4ef88a3bed
adi_board.tcl : Patch for adi_spi_core process
...
- Fix indentation
- Pacth for adi_spi_core process
2014-03-31 16:41:07 +03:00
7f4f200fce
Project scripts: Initial check in of adi_board.tcl
...
The script contains integration tcl processes.
2014-03-26 19:08:56 +02:00
f9a67371c0
Zynq Base System: Reset is synchronized to lowest system clock
...
System reset (sys_100m_reset) is synchronized to lowest system
clock (FCLK0), via a Processor System Reset module
2014-03-26 17:58:14 +02:00
ad5ef35b48
fmcomms1: modified *_bd.tcl files formatting
2014-03-26 12:05:42 +02:00
8f7d4c9b26
FMCOMMS1: Fixed typo in common/fmcomms1_bd.tcl
2014-03-25 14:34:55 +02:00
0f10623be4
AC701/VC707: Define common variables
...
Define variables sys_zynq, sys_mem_size, sys_addr_cntrl_space.
2014-03-25 14:24:51 +02:00
2070c66b87
Fmcomms1: Initial commit for KC705
...
Modified common project so it can be compatible for both ARM and
Microblaze based systems.
2014-03-24 16:52:24 +02:00
aa7b0bb4dd
VC707 basesys: General fixes, actual status: working
...
- Add an auxiliary cpu interconnect
- Add an auxiliary interrupt concatenation module
- Add new MIG file, current frequency of the DDR interface is 100
Mhz
- Memory interconnect optimisation strategy is 'Maximize
Performance'
2014-03-24 13:07:48 +02:00
b94acf78aa
AC701 bases sys: Add an auxiliary cpu interconnect
...
- Add an auxiliary cpu interconnect, the KC705 base system was
used as reference
- Base system is tested and working
2014-03-24 13:01:52 +02:00
792e8a208d
KC705 base system: Make a few cosmetic changes
2014-03-24 12:55:37 +02:00
f8c1179bc1
FMCOMMS2 KC705 Project.
...
Added the files required for the FMCOMMS2 KC705 project.
Both DMA and DDS work.
2014-03-24 11:48:52 +02:00
8a08031dce
AC701: Modify interrupt concatenation
...
- Interrupt concatenation is the same as in case of KC705
2014-03-24 10:20:56 +02:00
13b4dd07d0
KC705 base system: Modify interrupt concatanation
...
- Add an aditional interrupt input net for the sys_concat_aux_intc
module
2014-03-21 14:45:18 +02:00
c6143dbfaf
KC705 base system: Delete trailing whitespaces.
2014-03-21 14:42:27 +02:00
31a1ff384d
FMCOMMS2 Base Design tcl modified
...
Added support for both Zynq and MicroBlaze projects
2014-03-21 09:57:52 +02:00
3a0d1282b7
Fix the remaining issues
...
- Swap the IO locations of ports vsync and hsync
- Change the mem_interconnect optimization strategy to Maximize
Performance
2014-03-20 14:36:01 +02:00
698e9f4757
Added phys_opt_design step for fixing timing
...
The FMCOMMS1 meets timing on ZED/ZC702 only if the phys_opt_design step
is part of the implmentation flow, with the Explore argument.
"This step performs physical optimizations such as timing-driven
replicaiton of high fanouts nets to improve timing results"
2014-03-19 16:42:44 +02:00
7cdab9b5b0
Change the internal clock generator to Clock Wizard
...
- Using a Clock Wizard Module, in place of the DDR Controler's MMCM for internal clock
generation.
2014-03-18 17:24:45 +02:00
9d65071235
Merge branch 'master' of https://github.com/analogdevicesinc/hdl
2014-03-18 15:30:29 +02:00
2c898bf3a2
Added ZC706, ZC702 and ZED FMCOMMS2 Vivado Project
...
ZC706 runs rx_clk at 250 MHz.
ZC702 and ZED run rx_clk at 200 MHz due to slower fabric.
The ZC702 and ZED projects need init_user in the boot procedure in order for the HP Ports to work correctly.
Both DDS and DMA mode work.
2014-03-18 15:27:42 +02:00
f3c503cfb8
Merge branch 'master' of github.com:analogdevicesinc/hdl
2014-03-17 21:33:13 -04:00
dc44703cf1
zynq/non-zynq: identical signal names and instances
2014-03-17 17:02:03 -04:00
a6da4ca01c
zynq/non-zynq merge variables
2014-03-17 16:39:52 -04:00
ab8627e669
fmcomms1: Changed ILA data capture and sys constraints
...
The ILA can not work at 250MHz on ZED/ZC702. Because of this, the data
path was modified from 28bits@250MHz to 56bits@125MHz, by using a FIFO.
The ZED/ZC702 max BUFG frequency is 464MHz, which corresponds to a 2.16
period so the constraints were modified accordingly.
2014-03-17 15:50:01 +02:00
ee56db8d50
FMCOMMS2: Modified FCLK2 to 125 MHz, and xdc file
...
tcl: FCLK2 was modified from 100 MHz to 125 MHz.
xdc: rx_clk period constraint was redefined from 8ns (125 MHz) to 4ns (250 MHz)
2014-03-14 16:27:56 +02:00
7a6ce70e19
Fix default repository path for adi_project.tcl
...
Projects can be build by running 'source system_project.tcl' in
Vivado Tcl console.
2014-03-13 10:28:16 +02:00
a6c3cb29c6
Modified SPI and ILA in fmcomms2_bd.tcl
2014-03-12 16:52:22 +02:00
92aaf0bd51
FMCOMMS1: Updated projects and axi_ad9643 core
...
ZC702: Removed invalid address segments. Changed the constraints
for adc_clk to minimum possible value in order to meet timing.
ZED: Change the constraints for adc_clk to minimum possible value, in
order to meet timing
AXI_AD9643: Corrected the number of bits in the adc_mon_data bus
2014-03-12 16:23:41 +02:00
66c6b2b182
fmcomms2: added
2014-03-11 20:04:26 -04:00
f8ab734918
projects/fmcomms1: added
2014-03-11 12:16:25 -04:00
e1f23e7d49
Merge branch 'master' of github.com:analogdevicesinc/hdl
2014-03-11 09:58:34 -04:00
f3ae57a53e
global clock and reset names
2014-03-11 09:57:59 -04:00
75963ab376
Initial check in of VC707 base project
...
- All source files for the VC707 base project
- Update the common base system to the new naming convention
2014-03-10 17:26:17 +02:00
793bf2f350
Change the adi_project_run process to prevent "const_type UCF" issue
...
- Set the constraint type to XDC before run the synthesis
2014-03-07 11:06:11 +02:00
5c3b65d01b
adv7511: kc705/ac701 updates
2014-03-06 09:36:50 -05:00
b0a1fab743
adv7511/kc705: added
2014-03-05 10:43:16 -05:00
360f10395a
initial checkin
2014-03-03 13:42:25 -05:00
82115b138e
adv7511/ac701: initial checkin
2014-03-03 13:40:24 -05:00
c89477be5a
projects/adv7511: zynq boards
2014-03-03 10:16:49 -05:00
350ec5e633
changed path settings
2014-03-03 10:06:36 -05:00
3c0ea759a0
changed path settings
2014-03-03 10:06:02 -05:00
ddac1a8834
added common board files
2014-02-28 21:17:01 -05:00
Istvan Csomortani
Rejeesh Kutty
Adrian Costina
Michael Hennerich
Lars-Peter Clausen
acozma
dbogdan
ATofan
Istvan Csomortani