Explicitly select MIO 52 and 53 pins to be part of MDIO port.
MIO_52_PIN (MDIO 0 Clock, Output)
MIO_53_PIN (MDIO 0 Data, Input/Output)
After the tool version change, this pins where by default connected
as MIO GPIOs.
Explicitly disable the "Transfer Start Synchronisation Support"
since the sync lines are not connected in this project.
If the sync input line (s_axi_user[0] or fifo_wr_sync) are not connected,
Vivado 2017.4.1 no longer connects them to the defaultValue defined
in the axi_dmac ip (1). Instead he uses the defaulValue field defined
in the interface definition which in case of both interfaces is 0;
Loop back the unused GPIO pins, and add all the SPI interface to system
wrapper instance.
The following system_top modules were changed:
- ad738x_fmc
- ad7616_sdz
- ad77681evb
- ad77681evb
- ad7768evb
- ad9739a_fmc
- ad9434
- adrv9739
- fmcadc5
- ad6676evb
- ad9265
- ad5766
- fmcomms5
- m2k
The constraint where added to remove timing problems on the reset path.
The constraint paths do not match anymore. The resets are used in a synchronous
way so we don't need the timing exceptions anyway.
Projects affected by this change:
- daq3
- adrv9739
- ad6676evb
- fmcadc5
- daq2/kcu105
- fmcadc2
- adrv9371x
- fmcomms11/zc706
- fmcjesdadc1
By default every base design has a SPI interface (hard or soft). In
case of soft IPs (xilinx), the input registers of the interface by default have
the IOB attribute set to TRUE. If the interface are not used, the tool will
generate a critical warning, stating that IOB registers are not connected to
an IO buffer.
The following constraints are disabling the above setup for every base
design, which using a soft SPI IP.
Set the properties to mirror the hardware configuration so
the Vivado tools can provide warnings if there are any conflicts
between configuration pin settings, such as an IOSTANDARD
on a multi-function configuration pin that conflicts with the
configuration voltage.
see:
https://www.xilinx.com/support/documentation/user_guides/ug570-ultrascale-configuration.pdf
The following base constraints were updated:
- kcu105
- kc705
- vc707
- ac701
To reduce compilation time use default stratagies for synthesis and
implementation. If a project will require custom strategies, enable it
just for that particular project.
This modification will affect both Intel and Xilinx projects.
Vivado sometimes generates semi-valid or invalid warnings and critical warnings.
In the past these messages were silenced, by changing its message severity.
These setups were scattered in multiple scripts. This commit is an attempt
to centralize it and make it more maintainable and easier to review it.
The script specifies the OUT_CLK_SEL and SYS_CLK_SEL parameter values as
binary numbers. But the tools will interpret them as decimal number
resulting in the wrong selection for OUT_CLK_SEL. Specify the parameter
values as decimal values to avoid this.
This is not a critical issue since software will overwrite this setting at
system boot-up. But it should be fixed anyway.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The script specifies the OUT_CLK_SEL and SYS_CLK_SEL parameter values as
binary numbers. But the tools will interpret them as decimal number
resulting in the wrong selection for OUT_CLK_SEL. Specify the parameter
values as decimal values to avoid this.
This is not a critical issue since software will overwrite this setting at
system boot-up. But it should be fixed anyway.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes the following warning:
[Synth 8-2611] redeclaration of ansi port rx_sysref is not allowed
This is a leftover of commit 1c23cf4621 ("all: Update verilog files to
verilog-2001").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes the following warnings:
[Synth 8-2611] redeclaration of ansi port txnrx_0 is not allowed
[Synth 8-2611] redeclaration of ansi port enable_0 is not allowed
[Synth 8-2611] redeclaration of ansi port enable_1 is not allowed
[Synth 8-2611] redeclaration of ansi port txnrx_1 is not allowed
This is a leftover of commit 1c23cf4621 ("all: Update verilog files to
verilog-2001").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Make sure that the axi_adxcvr instances are configured with the same
transceiver type as the util_adxcvr.
This is necessary for software to be able to detect the transceiver type
and support dynamic reconfiguration.
It is also necessary for correct eye scan support in the axi_adxcvr block.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Make sure that the axi_adxcvr instances are configured with the same
transceiver type as the util_adxcvr.
This is necessary for software to be able to detect the transceiver type
and support dynamic reconfiguration.
It is also necessary for correct eye scan support in the axi_adxcvr block.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fix the location assignment of the transceiver blocks to get the correct
lane mapping.
Note that the comments indicating the expected lane mapping are correct,
but the actual transceiver location assignments were not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The external reference clock runs at 122.88 MHz by default. This means that
the QPLL feedback divider needs to be set to 80 so that the VCO is inside
the locking range (9.8 GHz - 16.375 GHz).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
AndreiGrozav
Laszlo Nagy
Istvan Csomortani
Adrian Costina
Lars-Peter Clausen
Michael Hennerich