The timing exceptions for the debug paths are currently a bit to broad and
can include paths that should not have an exception.
All the debug signals are coming from the i_request_arb instance, so
include that in the match to avoid false positives.
For most projects this wont have been a problem since there is usually a
fair amount of slack on the paths that were affected by this. But in
projects with high utilization this might result in undefined behavior.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fix the read side of the CDC data FIFO. The read address generation did not
function correctly.
Redesign the read side of the FIFO, and make sure that it becomes empty after
the DMA transfer ends; and never get stock in a cyclic mode.
The dac_last signal is not used anywhere in the module. Remove it and its
synchronization registers.
Fixes the following warnings:
[Synth 8-6014] Unused sequential element dac_dlast_reg was removed. ["axi_dacfifo_rd.v":372]
[Synth 8-6014] Unused sequential element dac_dlast_m1_reg was removed. ["axi_dacfifo_rd.v":373]
[Synth 8-6014] Unused sequential element dac_dlast_m2_reg was removed. ["axi_dacfifo_rd.v":374]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Commit bfc8ec28c3 ("util_axis_fifo: instantiate block ram in async mode")
added the read-enable (reb) signal to the ad_mem block.
It didn't update the ad_mem instance in axi_dacfifo_address_buffer.v. This
results in the read-enable of the address_buffer being tied to 0.
Fix this by connecting the same signal that increments the read address.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DMAC implementation guarantees that the expression `dma_valid &
dma_xfer_req` is always identical to just dma_valid.
When generating the util_dacfifo dma_wren_s signal the optimizer doesn't know
of this though and hence will route both signals into the LUT that drives
the write enable for the BRAMs.
Simplify the expression by removing dma_xfer_req from it. Considering this
can be a fairly high fan-out net and is typically the bottleneck for the
util_dacfifo timing this helps to improve the timing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Some parts of the util_cdc library rely on dead logic elimination to remove
unused logic. Unfortunately with newer Vivado versions this results in
warnings about unused sequential elements being removed. Like:
WARNING: [Synth 8-6014] Unused sequential element cdc_sync_stage1_reg was removed.
To avoid this encase the logic in generate blocks that makes sure they are
not generated when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
There are random timing violations on the A10GX board using the
DAQ3 and DAQ2 projects.
Setting the synthesis/implementation strategy to "HIGH PERFORMANCE
EFFORT" increases the success rate of the timing closure significantly.
This reverts commit 4b1d9fc86b "axi_dmac: Modified in order to avoid
vivado crash".
Vivado no longer crashes and this structure is much more efficient when it
comes to resource usage and timing. The intention here is to create a 1-bit
memory that is N entries deep and not a N bit signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The burst_count signal and its derived signals are not used until the
burst_count has been explicitly initialized by loading a transfer. There is
no need to have a reset.
This reduces the fan-out of the reset signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The data path register of the 2d_transfer module are qualified by the
corresponding valid signal. Their content is not used until they have been
explicitly initialized. There is no need to reset them explicitly.
This reduces the fan-out of the reset signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
There is no need to reset the data path in the address generator. The
values of the register on the data path are not used until they have been
explicitly initialized. Removing the reset simplifies the structure and
reduces the fan-out of the reset signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Xilinx tools don't allow to use $clog2() when computing the value of a
localparam, even though it is valid Verilog.
For this reason a parameter was used for BYTES_PER_BURST_WIDTH so far. But
that generates warnings from both Quartus and Vivado since the parameter is
not part of the parameter list.
Fix this by changing it to a localparam and computing the log2() manually.
The upper limit for the burst length is known to be 4k, so values larger
than that don't have to be supported.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
A larger store-and-forward memory provides better protection against worst
case memory interface latencies by being able to store more data before
over-/underflowing.
Based on empirical testing it was found that using a size of 4 bursts can
still result in underflows/overflows under certain conditions. These do not
happen when using a size of 8 bursts.
This change does not significantly increase resource consumption. Both on
Intel and Xilinx the block RAM has a minimum depth of 512 entries. With a
default burst length of 16 beats that allows for up to 32 bursts without
requiring additional block RAM.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The label for the store-and-forward memory size configuration option at the
moment is just "FIFO Size" and while the store-and-forward memory uses a
FIFO that is just a implementation detail.
Change the label to "Store-and-Forward Memory Size". This is more
descriptive as it references the function not the implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
For correct operation the store-and-forward memory size must be a
power-of-two in the range of 2 to 32.
This is simple enough so we can list all values and let the IP Integrator
and QSYS perform proper validation of the parameter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This comment hasn't been true in a long long time. It does not have any
relation to the code around it anymore.
So just remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
In the system top of the FMCOMMS5 projects, there are several GPIO lines, which
can not find in the constraint file, respectively gpio_open_15_15,
gpio_open_44_44 and gpio_45_45.
These are floating GPIO pins, as their names suggest. Delete all these wires and
update IOBUF instances.
Moved XCVR related connections to HP0, where the HP shares the MUX with the Video DMA
HP1 and HP2 are used for RX OS and RX DMAs, sharing the MUX. Usually they shouldn't run at the same time.
HP3 is used for TX DMA, sharing the MUX with the FPD DMA controller
All HPx and DMA buswidths have been increased to 128 bits
The HPx-DMA clock has been increased to 300 MHz
DAC FIFO address size has been increased to 17
* jesd204: Add RX error statistics
Added 32 bit error counter per lane, register 0x308 + lane*0x20
On the control part added register 0x244 for performing counter reset and counter mask
Bit 0 resets the counter when set to 1
Bit 8 masks the disparity errors, when set to 1
Bit 9 masks the not in table errors when set to 1
Bit 10 masks the unexpected k errors, when set to 1
Unexpected K errors are counted when a character other than k28 is detected. The counter doesn't add errors when in CGS phase
Incremented version number
Adrian Costina
Istvan Csomortani
Lars-Peter Clausen
AndreiGrozav
Laszlo Nagy