Some FMC boards do utilize more than one transceiver quad but do not
necessarily use all transceivers in a quad. On such board is the
AD9694-500EBZ. Which uses two transceivers each in two adjacent quads.
This board can not be supported by instantiating a util_adxcvr with only 4
lanes. Since those 4 lanes would be packed into the same quad. Instead it
it is necessary to instantiate a util_adxcvr with 6 lanes. 4 lanes for the
first quad and 2 for the second.
To still to be able to connect such a util_adxcvr to a link layer with only
4 lanes allow to specify sparse lane mappings. A sparse mapping can have
less lanes than the util_adxcvr and some lanes will be left unconnected.
For example for the AD9694-500EBZ the lane mapping looks like the following:
ad_xcvrcon util_ad9694_xcvr axi_ad9694_xcvr ad9694_jesd {0 1 4 5} rx_device_clk
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Sometimes the output clock of the transceiver should not be used for the
device clock.
E.g. for deterministic latency with no uncertainty the device clock needs
to be sourced directly from a clock or transceiver reference clock input
pin.
Add an option to the ad_xcvrcon command to specify the device clock.
In case the same device clock is used for multiple JESD204 links, e.g. a TX
and a RX link only one reset generator is created.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This change adds the TLAST signal to the AXI streaming interface
of the source side for Intel targets.
Xilinx based designs already have this since the tlast is part of the
interface definition.
In order to make the signal optional and let the tool connect a
default value to the it, the USE_TLAST_SRC/DEST parameter is
added to the configuration UI. This conditions the tlast port on
the interface of the DMAC.
Xilinx handles the optional signals much better so the parameter
is not required there.
There are random timing violations on the A10GX board using the
DAQ3 and DAQ2 projects.
Setting the synthesis/implementation strategy to "HIGH PERFORMANCE
EFFORT" increases the success rate of the timing closure significantly.
In the system top of the FMCOMMS5 projects, there are several GPIO lines, which
can not find in the constraint file, respectively gpio_open_15_15,
gpio_open_44_44 and gpio_45_45.
These are floating GPIO pins, as their names suggest. Delete all these wires and
update IOBUF instances.
Moved XCVR related connections to HP0, where the HP shares the MUX with the Video DMA
HP1 and HP2 are used for RX OS and RX DMAs, sharing the MUX. Usually they shouldn't run at the same time.
HP3 is used for TX DMA, sharing the MUX with the FPD DMA controller
All HPx and DMA buswidths have been increased to 128 bits
The HPx-DMA clock has been increased to 300 MHz
DAC FIFO address size has been increased to 17
In DUAL mode half of the data ports are unused and the unused inputs need
to be connected to dummy signals.
Completely hide the unused ports in DUAL mode to remove that requirement.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Connect the DAC data underflow pin (fifo_rd_underflow) of the DMA
to the dunf pin of the device core. This way the software can detect
underflows in the DAC data path.
Connect the DAC data underflow pin (fifo_rd_underflow) of the DMA
to the dunf pin of the device core. This way the software can detect
underflows in the DAC data path.
Connect the DAC data underflow pin (fifo_rd_underflow) of the DMA
to the dunf pin of the device core. This way the software can detect
underflows in the DAC data path.
AndreiGrozav
Lars-Peter Clausen
Laszlo Nagy
Adrian Costina
Istvan Csomortani