Fix the following warnings that are generated by Quartus:
Warning (10230): Verilog HDL assignment warning at ad_sysref_gen.v(68): truncated value with size 32 to match size of target (8)
No functional changes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fix the following warnings that are generated by Quartus:
Warning (10036): Verilog HDL or VHDL warning at ad_datafmt.v(69): object "sign_s" assigned a value but never read
Move the sign_s and signext_s signals into the generate block in which
they are used.
No functional changes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fix the following warnings that are generated by Quartus:
Warning (10236): Verilog HDL Implicit Net warning at util_dacfifo.v(257): created implicit net for "dac_mem_ren_s"
Warning (10230): Verilog HDL assignment warning at util_dacfifo.v(166): truncated value with size 32 to match size of target (10)
Warning (10230): Verilog HDL assignment warning at util_dacfifo.v(266): truncated value with size 32 to match size of target (10)
Warning (10230): Verilog HDL assignment warning at util_dacfifo.v(268): truncated value with size 32 to match size of target (10)
No functional changes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The primary use-case of the DMA controller is in non-2D mode. Make this the
default, since allows projects to instantiate the controller with the
default configuration without having to explicitly disable 2D support.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the file names must have the same name as its module. Change all the
files, which did not respect this rule.
Update all the make files and Tcl scripts.
Most of the cores are fully covered by the generic constraint files. When
the constraints where moved from the core specific to the generic
constraint files some empty core constraints files where left around. These
don't do anything, so remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The standard Makefile output is very noisy and it can be difficult to
filter the interesting information from this noise.
In quiet mode the standard Makefile output will be suppressed and instead a
short human readable description of the current task is shown.
E.g.
> make adv7511.zed
Building axi_clkgen library [library/axi_clkgen/axi_clkgen_ip.log] ... OK
Building axi_hdmi_tx library [library/axi_hdmi_tx/axi_hdmi_tx_ip.log] ... OK
Building axi_i2s_adi library [library/axi_i2s_adi/axi_i2s_adi_ip.log] ... OK
Building axi_spdif_tx library [library/axi_spdif_tx/axi_spdif_tx_ip.log] ... OK
Building util_i2c_mixer library [library/util_i2c_mixer/util_i2c_mixer_ip.log] ... OK
Building adv7511_zed project [projects/adv7511/zed/adv7511_zed_vivado.log] ... OK
Quiet mode is enabled by default since it generates a more human readable
output. It can be disabled by passing VERBOSE=1 to make or setting the
VERBOSE environment variable to 1 before calling make.
E.g.
> make adv7511.zed VERBOSE=1
make[1]: Entering directory 'library/axi_clkgen'
rm -rf *.cache *.data *.xpr *.log component.xml *.jou xgui
*.ip_user_files *.srcs *.hw *.sim .Xil .timestamp_altera
vivado -mode batch -source axi_clkgen_ip.tcl >> axi_clkgen_ip.log 2>&1
...
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The include files are currently only implicitly added to the component file
list. Do it explicitly as this will make sure that they show up in the
generated Makefile dependency list.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Some IP core have files in their file list for common modules that are not
used by the IP itself. Remove those.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DC filter implementation in library/common/dc_filter.v is Xilinx
specific as it uses the Xilinx DSP48 hard-macro. There is a matching Altera
specific implementation in library/altera/common/dc_filter.v.
Move the Xilinx specific implementation from the generic common folder to
the Xilinx specific common folder in library/xilinx/common/ since that is
where all other Xilinx specific common modules reside.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the IP component dependency in the Makefile system is the Vivado
project file. The project file is only a intermediary product in producing
the IP component definition file.
If building the component definition file fails or the process is aborted
half way through it is possible that the Vivado project file for the IP
component exists, but the IP component definition file does not.
In this case there will be no attempt to build the IP component definition
file when building a project that has a dependency on the IP component.
Building the project will fail in this case.
To avoid this update the Makefile rules so that the IP component definition
file is used as the dependency. In this case the IP component will be
re-build if the component definition file does not exist, even if the
project file exists.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The library Makefiles for share most of their code. The only difference is
the list of project dependencies.
Create a file that has the common parts and can be included
by the library Makefiles.
This drastically reduces the size of the library Makefiles and also allows
to change the Makefile implementation without having to re-generate all
Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
In cases when a shallow FIFO is requested the synthesizer infers distributed RAM
instead of block RAMs. This can be an issue when the clocks of the FIFO are
asynchronous since a timing path is created though the LUTs which implement the
memory, resulting in timing failures. Ignoring timing through the path is not a
solution since would lead to metastability.
This does not happens with block RAMs.
The solution is to use the ad_mem (block RAM) in case of async clocks and letting
the synthesizer do it's job in case of sync clocks for optimal resource utilization.
Add a parameter to the control the clock source option of the MMCM. If
the MMCM has only one clock source the CLKSEL pin will be tied to VDD.
The previous version added a redundant path between the CLKSEL port and
register map.
This module upscale an n*sample_width data bus into a 16 or 32*n data
bus. The samples are right aligned and supports offset binary or two's
complement data format.
The up_xfer_cntrl and up_xfer_status modules have its own constraints files
in library/xilinx/common. Each IP which has an instance of these
modules, have to use these constraints files.
The following IPs were modified:
- axi_adc_decimate
- axi_adc_trigger
- axi_dac_interpolate
- axi_logic_analyzer
A couple of new parameters and new ports are missing in several
up_[adc|dac]_[common|channel] instance, and generates warnings. The rule of
thumb is to use full instantiations, defining all the existing parameter and
ports of the module.
Fix all the instantiation of up_[adc|dac]_[common|channel], by defining all its
parameters and ports.
The up_rstn is driven by s_axi_resetn, which is generated by a
Processor System Reset module. (connected to port peripheral_aresetn)
Therefor using this reset signal as an asynchronous reset is redundant,
and a bad design practice at the same time. Asynchronous reset should be
used if it's inevitable.
Vivado sometimes generates semi-valid or invalid warnings and critical warnings.
In the past these messages were silenced, by changing its message severity.
These setups were scattered in multiple scripts. This commit is an attempt
to centralize it and make it more maintainable and easier to review it.
The cores that handle the JESD204 ADC cores do not feature IQ correction
logic. The Q_OR_I_N parameter for the channel modules is unused, so remove
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The cores that handle the JESD204 ADC converters do not feature any direct
IO and subsequently no IO-delay blocks either. Remove the unused
IO_DELAY_GROUP parameter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Bundle the TLAST signal in with the other AXIS slave signals to enable
easier connection between AXIS devices that use TLAST
Signed-off-by: Matt Fornero <matt.fornero@mathworks.com>
Add some limit TLAST support for the streaming AXI source interface. An
asserted TLAST signal marks the end of a packet and the following data beat
is the first beat for the next packet.
Currently the DMAC does not support for completing a transfer before all
requested bytes have been transferred. So the way this limited TLAST
support is implemented is by filling the remainder of the buffer with 0x00.
While the DMAC is busy filling the buffer with zeros back-pressure is
asserted on the external streaming AXI interface by keeping TREADY
de-asserted.
The end of a buffer is marked by a transfer that has the last bit set in
the FLAGS control register.
In the future we might add support for transfer completion before all
requested bytes have been transferred.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Commit ff50963c7f ("axi_ad9361- altera/xilinx reconcile- may be broken-
do not use") inverted the polarity of the TX feedback clock.
This exposed some issues in the existing drivers which can cause the
interface tuning to fail randomly under certain conditions.
To keep backwards compatibility with existing drivers restore the previous
behavior.
A separate fix will be applied to the drivers that resolves the issue that
has been exposed by the polarity inversion. So that interface calibration
works reliably under all conditions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Assigning the value of a local parameter(localparam) to a parameter
will end up with a conflict(not highlighted by the tool). In this
case, the parameter type was defined as a string instead of an
integer. Furthermore, this scenario leads to an undesired choice
between primitive types.
The dma_last_beats is used by the Avalon Memory Mapped interface
controller, to define the last burst length.
Its value get stable after the last valid data of the DMA interface, and staying
stable until the positive edge of the DMA's xfer_req.
No need to condition the transfer of this register to avalon clock
domain.
The XFER_END state defines the end of a transaction, when the entire
data set is written or read to/from the DDRx memory.
A transaction can contain multiple Avalon bursts. Make sure that the FSM
goes back into staging phase at the end of each burst; also define a
signals which indicate the end of each burst for control.
The period_count should be updated once per clock cycle. This is not
enforced with the current implementation, which probably leads to
period_count being decremented on both m_axis_aclk edges.
A problem observed due to this is that the m_axis_tlast output is not
asserted or is asserted for a too short time for the consumer to
detect it.
Fix by letting the decrement (and thus the m_axis_tlast toggling)
happen only on the rising edge of the m_axis_aclk clock.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
The commit 6900c have added an additional register stage into the fifo read
data path, but the control signals (ready/valid/underflow) were not realigned
to the data. This can cause data lose or duplicated samples in some case.
Realign the control signals to the data.
The util_adxcvr supports GTX2, GTH3 and GTH4. The transceiver is selected
using the XCVR_TYPE parameter.
The axi_adxcvr on the other hand only has a configuration parameter to
indicate whether a GTX or GTH transceiver is used (GTH_OR_GTX_N). Since
there are some minor differences between GTH3 and GTH4 that software needs
to know about rename the GTH_OR_GTX_N to XCVR_TYPE and match use the same
semantics as util_adxcvr.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The dac_xfer_req should indicate one single thing, that the FIFO is in
read phase. Should not be affected by any signals, which indicates data
validity on any interface. (e.g. dac_valid)
This signal is not used by the device core, its main purpose is to
indicate the state of the interface for a posible intermediat processing
module.
Fix the reset of the dma_mem_waddr (write address register of the CDC
FIFO on DMA's clock domain). This solves the occasional invalid read backs after
multiple re-initialization of the PL_DDR_FIFO.
+ Build both the read and write logic around an FSM
+ Consistent naming of registers and wires
+ Add support for burst lenghts higher than one, current burst lenght
is 64
+ Fix all the bugs, and make it work (first bring up with
adrv9371x/a10soc)
Istvan Csomortani
Lars-Peter Clausen
Laszlo Nagy
Adrian Costina
Rejeesh Kutty
AndreiGrozav
Matt Fornero
Luca Ceresoli