88a3b7f8fd
library: remove all constraints for now
2014-10-07 16:59:19 -04:00
27153fff41
ad9625x2_fmc: updated to 2014.2
2014-10-07 16:05:09 -04:00
2dfcb0c599
usdrx1: Initial commit for a5gt
...
axi_ad9671: added start of frame information to the altera core.
2014-10-07 19:41:54 +03:00
95842b8949
ad9434_fmc: Fix adc_valid signal path
2014-10-07 18:02:33 +03:00
a436153a48
axi_ad9434: Independent read/write update
...
Independent read/write is supported on "up" interface.
2014-10-07 18:01:44 +03:00
115f33b8d6
ad9434_fmc: Fix pin constraints for ZC706
2014-10-07 17:58:29 +03:00
9404e93126
ad9434_fmc: Fix PN monitor.
...
No need to flop the incoming data.
2014-10-07 17:56:27 +03:00
c1213ffe71
ad9434_fmc: Fix SPI interface
2014-10-07 17:51:14 +03:00
66baf6ac3e
axi_ad9434: Deleted unused ip file
...
ad_lvds_in.v is not used in this ip core.
2014-10-07 17:47:08 +03:00
bfa17844ff
ad_serdes_in: General update
...
Added a parameter for option SDR / DDR mode, added a parameter for parallel data width.
Note: default IF_TYPE is SDR and default PARALLEL_WIDTH is 8
2014-10-07 17:42:27 +03:00
151781a2af
axi_ad9467: Fix PN sequence checker
...
Make sure that the reference PN sequence is only incremented every two clock
cycles to make sure that it matches the rate of the ADC PN sequence.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-07 16:26:53 +03:00
59640f181b
ad9467: Fix LVDS delay interface.
2014-10-07 16:25:22 +03:00
cd42345324
projects/common/xxx/xxx_system_bd.tcl: 'Update microblaze defaults
...
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
2014-10-07 09:17:24 +02:00
bca8ec0160
daq2: 2014.2 and ver.d
2014-10-06 14:56:01 -04:00
c375b5b26e
daq3: vivado build
2014-10-06 10:34:02 -04:00
d47776a4a0
ad9152: 9144 copy
2014-10-06 10:34:01 -04:00
525373fc04
daq3: daq2 copy
2014-10-06 10:34:00 -04:00
210da4116f
scripts: initial commit
2014-10-03 16:13:34 -04:00
581892b22a
axi_ad9265: Updated project with new up independent read/write
2014-10-03 12:32:08 +03:00
de33722470
up/constr: independent read/write and local constraints
2014-10-02 14:35:59 -04:00
f0927afd0b
ad9625_fmc: add dma fifo for non-zynq
2014-10-01 14:51:14 -04:00
89964be59e
fmcomms1: Updated project to vivado 2014.2
2014-09-30 10:32:18 +03:00
041d8faaf7
common: Updated common projects for ac701/kc702/zc702/zed to vivado 2014.2
2014-09-30 10:31:00 +03:00
922bc6f03a
fmcadc3: 16bit - but ignored 4 lsb(s)
2014-09-29 15:26:30 -04:00
3c25c1171d
fmcomms1: Fixed missing sample issue on ZC706. Added modifications for all other platforms
2014-09-26 10:28:07 -04:00
87c4c73e22
ad9434: Fix adc_clk constraint
...
ADC clock is 500 Mhz.
2014-09-25 16:54:06 +03:00
82ed885b53
ad9434: Fix SPI line physical constraints
...
SPI lines are not differential.
2014-09-25 16:53:16 +03:00
6a09a1ed19
ad9434: Fix the processor read interface
...
Fix the processor read interface, preventing to have nets with multiple drivers. Made a few cosmetic changes in the code too.
2014-09-25 16:51:58 +03:00
ccb0b135ca
ad9434: Fix the adc to dma interface.
...
All the device2dma interfaces needs to have a generic form : (data, enable, valid)/channel
2014-09-25 16:50:09 +03:00
d5f4991e26
ad9434: Merge the ad9434_if interface data outputs into one single bus
2014-09-25 16:45:12 +03:00
079ed0ffb3
ad_serdes_in: Update the serdes_in module
...
Add additional IDELAY block before the ISERDES. Delet the IDDR blocks. Be aware, the ISERDES block are running in DDR mode. If the interface is SDR the maximum parallel data width is 4.
2014-09-25 16:40:29 +03:00
27ffff827a
common: Initial check in of ad_serdes_in.v
...
A generic serdes module for input interface, support both 6 and 7 series.
2014-09-24 18:34:40 +03:00
683561b67d
AD9434: Initial check in of the library and project with ZC706
2014-09-24 18:27:17 +03:00
1d4bc47cea
ad9265: Initial commit
2014-09-23 22:51:42 -04:00
296983707b
usdrx1: Updated project to 2014.2
2014-09-23 22:45:50 -04:00
5af2474d51
usdrx1: axi_ad9671 / axi_jesd_gt added signal for frame synchronization
2014-09-23 22:44:33 -04:00
bdf01738a1
ultrasound: disconnected ADN4670 chips from SPI lines.
...
Connected everything to ground so that the the clock selected is 0 and all outputs are enabled
2014-09-23 22:30:42 -04:00
7e40f99fe9
fmcomms2: Improved constraints for ac701 and zc702. Fixed common design so that ILA works correctly on microblaze based systems
2014-09-23 22:28:27 -04:00
577441bd0c
daq1: clean up dma interfaces
2014-09-23 14:23:41 -04:00
7c98a783c5
2014.2 updates
2014-09-23 12:32:33 -04:00
1682d9da10
fmcadc3: initial updates
2014-09-22 11:27:17 -04:00
5e3076d770
fmcadc3: daq2 copy
2014-09-22 11:27:16 -04:00
e528ee0b52
axi_ad9234: axi_ad9680 copy
2014-09-22 11:27:15 -04:00
dd7bac41c1
daq1 : Update project to 2014.2
...
- Cores are upadted
- Concat module does not swap output anymore
- Clock signal name ps7_clk_* changed to clk_fpga_*
2014-09-22 17:33:50 +03:00
f2cd7626f5
adi_project : ZC706 board name changed on 2014.2
2014-09-22 17:33:49 +03:00
fb5d212370
daq2/kcu105: fixed timing violations
2014-09-19 15:55:42 -04:00
751bdd6cfc
daq1: Update the constraint file
...
- tx_ref_clk and rx_sysref need to be differential
- cosmetic changes
2014-09-19 18:22:57 +03:00
f43b5d707e
fmcomms2: Reduced clock frequency for ILA to meet timing for ZED
...
Modified ZED constraints to 250 MHz for the clock from AD9361
2014-09-16 16:08:28 -04:00
d33fb07587
usdrx1: Modified the GPIO assignments so that board specific GPIOs start from GPIO 32.
...
GPIOs for which the directions is known, have been specifically assigned.
The SPI clock has been changed to a lower frequency.
2014-09-16 15:56:19 -04:00
d4db53c3b0
usdrx1_spi: Modified module to be compatible with altera
2014-09-16 15:53:11 -04:00
Rejeesh Kutty
Adrian Costina
Istvan Csomortani
Lars-Peter Clausen
Michael Hennerich