- Quartus version was updated
- the start_n output port was deteled from system_top.v
- the ""mixed_port_feed_through_mode" parameter of RAM can not have value "old"" warning was disabled
- update Makefile copyright year
Signed-off-by: Paul Pop <paul.pop@analog.com>
bug:
say "make LVDS_CMOS_N=0"
- will set ad_project_dir as LVDSCMOSN0
- will then set system_qip_file as LVDSCMOSN0/system_bd/synthesis/system_bd.qip
- build error reveals system_bd can't be found
- maybe due to setting ad_project_dir as a relative file path
fix:
- set ad_project_dir as an absolute file path
Signed-off-by: Jem Geronimo <Johnerasmusmari.Geronimo@analog.com>
If the sampling clock is lower than dclk*number_of_active_lines*32 the interface should wait for the next adc_ready signal to reset the counter.
The adc_valid_p signal should be set high just for a clock period after the sample was captured.
- Issue introduced by commit 173f4a83d4
- When IODELAY_ENABLE was inserted in axi_adrv9001_if for adrv9001_rx (Xilinx instance),
for Intel instance (intel/adrv9001_rx.v) was omitted and caused a build error for
adrv9001/a10soc
Signed-off-by: Iulia Moldovan <Iulia.Moldovan@analog.com>
Replaced the existing axi_tdd with the new version
* Added DEFAULT_POLARITY synth parameter and RO register
* Added TDD_STATUS register
* Added TDD_SYNC_RST feature
* Used the asy_ prefix for signals which are not synced
* Added logic to force the state from ARMED to RUNNING when startup_delay=0
* Added feature to finish the burst when the module is disabled before its completion
Signed-off-by: Ionut Podgoreanu <ionut.podgoreanu@analog.com>
Running 'make' will build the default project directly in the project folder (like it did before)
Running 'make RX_LANE_RATE=15 TX_LANE_RATE=15' will build the project inside the 'RXRATE15_TXRATE15' subdirectory.
Running 'make CFG=cfg/test_config.txt" will use the variables found inside the configuration file and build the project inside the 'test_config' subdirectory.
Running 'make clean' will clean the default project only.
Running 'make CFG=cfg/test_config.txt clean' will clean the 'testconfig' build.
Running 'make clean-all' will delete all the built configurations and libraries.
Note that the 'JESD' and 'LANE' words from the parameter names are stripped.
Signed-off-by: Bogdan Luncan <bogdan.luncan@analog.com>
In ad_xcvrcon procedure from adi_board, phy_en_char_align must be connected only when 8B10B encoding is used,
otherwise this signal does not exists in the JESD ip and will cause an error.
Signed-off-by: Filip Gherman <Filip.Gherman@analog.com>
New improvements for the ADI DMAC IP:
1)The capability to manually overwrite the DMA_AXI_ADDR_WIDTH(from GUI or from tcl)
2)DMA_AXI_ADDR_WIDTH attribute is now visible in the Vivado GUI:
-"Auto mode": Automatically calculated by the core tcl files based on the existing attached address segments.
-"Manual mode": Specify the desired dma_width between 32-64 bits.
3)Added two new debug registers that return higher part of the current source/destination address.
Signed-off-by: Filip Gherman <Filip.Gherman@analog.com>
Paul Pop
laurent-19
Jem Geronimo
Iulia Moldovan
alin724
Istvan-Zsolt Szekely
AndrDragomir
LIacob106
Filip Gherman
AndreiGrozav
sergiu arpadi
Ionut Podgoreanu
Bogdan Luncan
Travis F. Collins
Laszlo Nagy