1375dcfeaa
daq3: Use new pack/unpack infrastructure
...
Use the new util_cpack2 and util_upack2 cores. They have lower utilization
that the old util_cpack and util_upack cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2018-11-28 11:33:11 +02:00
db51fb2829
daq3: ZCU102: Remove Offload FIFO for ADC path.
...
DAC FIFO cannot be increased because of timing violations
2018-08-23 18:06:32 +03:00
c794cbb49d
daq3: Connect the DAC data underflow
...
Connect the DAC data underflow pin (fifo_rd_underflow) of the DMA
to the dunf pin of the device core. This way the software can detect
underflows in the DAC data path.
2018-04-13 18:46:29 +03:00
1a9497b5b6
daq3: Add parameters for default xcvr configuration
...
The default configuration should be:
- line rate 12.33 Gbps
- core clk 308 MHz
2018-04-11 15:09:54 +03:00
7f377454a8
daq2/fmcadc4/daq3: Disable the transfer start sync on the ADC DMA
...
Explicitly disable the "Transfer Start Synchronisation Support"
since the sync lines are not connected in this project.
If the sync input line (s_axi_user[0] or fifo_wr_sync) are not connected,
Vivado 2017.4.1 no longer connects them to the defaultValue defined
in the axi_dmac ip (1). Instead he uses the defaulValue field defined
in the interface definition which in case of both interfaces is 0;
2018-04-11 15:09:54 +03:00
207f00a752
projects/ remove upack dma_xfer_in
2017-07-31 09:12:05 -04:00
0360e8587e
Connect JESD204 interrupts
...
Connect the ADI JESD204 link layer peripheral interrupt signals in all
projects.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-07-05 14:37:50 +02:00
b0ebf2df06
daq3: Provide DAC JESD204 lane mapping
...
The DAQ3 does not use a 1-to-1 lane mapping for the DAC JESD204 link.
Provide the proper mapping when setting up the transceiver connections.
Without this the payload data will be mapped incorrectly and the
transmitted signals are scrambled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-06-30 16:01:10 +02:00
a38bbb7eb4
daq3: Convert to ADI JESD204
...
Convert the DAQ3 project to the ADI JESD204 link layer cores. The change is
very straight forward, but a matching change on the software side is
required.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-05-23 11:16:07 +02:00
4eaa43f8e1
daq3: Update IP instantiations
2017-04-21 15:07:41 +03:00
d08d1d5a1b
adrv9371x ,daq3, fmcomms7, fmcomms11: add dac_fifo missing reset connection
2017-03-10 14:20:42 +02:00
6b1a8852a9
dacfifo- bypass port name change
2017-02-27 16:06:39 -05:00
862bd7ef2c
daq3/zc706- xcvr changes
2016-11-23 15:02:20 -05:00
bab9b2df0b
daq3/zc706: Update project with the new transceiver modules
2016-10-05 17:41:25 +03:00
bae63ae5b1
version_upgrade: Update the DAQ3 project to 2016.2
2016-09-06 11:41:37 +03:00
012b095006
daq3: Updated common design to 2015.4
2016-03-17 11:44:27 +02:00
b93af3c21e
daq3- bd updates
2015-09-30 10:11:49 -04:00
6c7316fbd0
daq3: Drop explicit axi_dmac clock synchronicity configuration
...
The axi_dmac core is now capable of detecting whether its different parts
run in different clock domains or not. No need to configure it manually any
more.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-09-18 15:27:56 +02:00
d52308f074
axi_dmac: Change parameter name 2D_TRANSFER
...
Parameter name can't start with numbers, 2D_TRANSFER was changed to DMA_2D_TRANSFER
2015-08-20 10:14:22 +03:00
57cfb7cfb1
hdl/library: Update the IP parameters
...
The following IP parameters were renamed:
PCORE_ID --> ID
PCORE_DEVTYPE --> DEVICE_TYPE
PCORE_IODELAY_GROUP --> IO_DELAY_GROUP
CH_DW --> CHANNEL_DATA_WIDTH
CH_CNT --> NUM_OF_CHANNELS
PCORE_BUFTYPE --> DEVICE_TYPE
PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE
CHID --> CHANNEL_ID
PCORE_DEVICE_TYPE --> DEVICE_TYPE
PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N
PCORE_SERDES_DDR_N --> SERDES_DDR_N
PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE
DP_DISABLE --> DATAPATH_DISABLE
PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE
C_BIG_ENDIAN --> BIG_ENDIAN
C_M_DATA_WIDTH --> MASTER_DATA_WIDTH
C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH
NUM_CHANNELS --> NUM_OF_CHANNELS
CHANNELS --> NUM_OF_CHANNELS
PCORE_4L_2L_N -->QUAD_OR_DUAL_N
C_ADDRESS_WIDTH --> ADDRESS_WIDTH
C_DATA_WIDTH --> DATA_WIDTH
C_CLKS_ASYNC --> CLKS_ASYNC
PCORE_QUAD_DUAL_N --> QUAD_DUAL_N
NUM_CS --> NUM_OF_CS
PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID
PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID
PCORE_CLK0_DIV --> CLK0_DIV
PCORE_CLK1_DIV --> CLK1_DIV
PCORE_CLKIN_PERIOD --> CLKIN_PERIOD
PCORE_VCO_DIV --> VCO_DIV
PCORE_Cr_Cb_N --> CR_CB_N
PCORE_VCO_MUL --> VCO_MUL
PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC
PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH
PCORE_ADDR_WIDTH --> ADDRESS_WIDTH
DADATA_WIDTH --> DATA_WIDTH
NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS
DEBOUNCER_LEN --> DEBOUNCER_LENGTH
ADDR_WIDTH --> ADDRESS_WIDTH
C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED
Cr_Cb_N --> CR_CB_N
ADDATA_WIDTH --> ADC_DATA_WIDTH
BUFTYPE --> DEVICE_TYPE
NUM_BITS --> NUM_OF_BITS
WIDTH_A --> A_DATA_WIDTH
WIDTH_B --> B_DATA_WIDTH
CH_OCNT --> NUM_OF_CHANNELS_O
M_CNT --> NUM_OF_CHANNELS_M
P_CNT --> NUM_OF_CHANNELS_P
CH_ICNT --> NUM_OF_CHANNELS_I
CH_MCNT --> NUM_OF_CHANNELS_M
4L_2L_N --> QUAD_OR_DUAL_N
SPI_CLK_ASYNC --> ASYNC_SPI_CLK
MMCM_BUFIO_N --> MMCM_OR_BUFIO_N
SERDES_DDR_N --> SERDES_OR_DDR_N
CLK_ASYNC --> ASYNC_CLK
CLKS_ASYNC --> ASYNC_CLK
SERDES --> SERDES_OR_DDR_N
GTH_GTX_N --> GTH_OR_GTX_N
IF_TYPE --> DDR_OR_SDR_N
PARALLEL_WIDTH --> DATA_WIDTH
ADD_SUB --> ADD_OR_SUB_N
A_WIDTH --> A_DATA_WIDTH
CONST_VALUE --> B_DATA_VALUE
IO_BASEADDR --> BASE_ADDRESS
IO_WIDTH --> DATA_WIDTH
QUAD_DUAL_N --> QUAD_OR_DUAL_N
AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT
ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH
ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH
MODE_OF_ENABLE --> CONTROL_TYPE
CONTROL_TYPE --> LEVEL_OR_PULSE_N
IQSEL --> Q_OR_I_N
MMCM --> MMCM_OR_BUFR_N
2015-08-19 14:11:47 +03:00
6c0ad6ede8
daq3: bsplit/ccat -- removed
2015-07-15 13:05:53 -04:00
6862655b0d
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-06-26 11:07:10 +02:00
71b5004b25
projects- drp moved to up-clock domain
2015-06-01 14:57:59 -04:00
2fa475cca2
daq3: 2014.4 updates
2015-03-19 12:45:50 -04:00
26d72d306e
daq3: compilation fixes - latest changes
2014-12-08 14:51:51 -05:00
cc265b6b9c
daq2/daq3/ad9625_fmc: Connect ADC DMA xfer_req signal
...
For proper operation the xfer_req signal needs to be connected from the ADC DMA to the DDR FIFO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-29 18:15:54 +01:00
17675863e0
all_projects: Fix the interrupt connections to preserve IRQ layout
2014-10-22 11:48:08 +03:00
2600b1f359
daq3: tx interleave and dma fifo axi streaming
2014-10-15 14:51:04 -04:00
c375b5b26e
daq3: vivado build
2014-10-06 10:34:02 -04:00
525373fc04
daq3: daq2 copy
2014-10-06 10:34:00 -04:00
Lars-Peter Clausen
Adrian Costina
Istvan Csomortani
AndreiGrozav
Laszlo Nagy
Rejeesh Kutty