The new REG_PRBS_CNTRL and REG_PRBS_STATUS registers expose controls of internal
PRBS generators and checkers allowing the testing the multi-gigabit serial link
at the physical layer without the need of the link layer bringup.
Fix library makefiles dep list using generic vendor info reg
Combine adi_int_bd_tcl with adi_auto_fill_bd_tcl procedure.
This change will simplify the process of generating makefiles for each library.
Removing the bd.tcl script from the adi_ip_files list will remove it from the
make dependency list.
Common basic steps:
- Include/create infrastructure:
* Intel:
- require quartus::device package
- set_module_property VALIDATION_CALLBACK info_param_validate
* Xilinx
- add bd.tcl, containing init{} procedure. The init procedure will be
called when the IP will be instantiated into the block design.
- add to the xilinx_blockdiagram file group the bd.tcl and common_bd.tcl
- create GUI files
- add parameters in *_ip.tcl and *_hw.tcl (adi_add_auto_fpga_spec_params)
- add/propagate the info parameters through the IP verilog files
axi_clkgen
util_adxcvr
ad_ip_jesd204_tpl_adc
ad_ip_jesd204_tpl_dac
axi_ad5766
axi_ad6676
axi_ad9122
axi_ad9144
axi_ad9152
axi_ad9162
axi_ad9250
axi_ad9265
axi_ad9680
axi_ad9361
axi_ad9371
axi_adrv9009
axi_ad9739a
axi_ad9434
axi_ad9467
axi_ad9684
axi_ad9963
axi_ad9625
axi_ad9671
axi_hdmi_tx
axi_fmcadc5_sync
Fix the following warning:
WARNING: [Synth 8-2611] redeclaration of ANSI port up_es_reset is not allowed
Also make sure, that in all configurations, the register has a diver.
Expose the TX configurable driver ports, more specifically the
TX_DIFFCTRL, TX_POSTCURSORE and TX_PRECURSORE for software. This
provides a soft tunning capability of the transmit side of the
transceivers, in cases where the insertion loss of the channel is too
high or low, comparing to the default value supported by the default
configuration of the GTs.
You can find information about these configuration ports under the
section called 'TX Configurable Driver' in the GT transceivers user
guide. (UG476, UG576)
The Xilinx's reset interface expect that every reset have an associated
interface and clock signal. The tool will try to find its clock and interface,
and automatically associated clock signal to it.
The PLL resets are individual asynchronous resets. To simplify the design
and avoid invalid critical warnings all the reset interface inference
for the PLL resets were removed.
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The util_adxcvr supports GTX2, GTH3 and GTH4. The transceiver is selected
using the XCVR_TYPE parameter.
The axi_adxcvr on the other hand only has a configuration parameter to
indicate whether a GTX or GTH transceiver is used (GTH_OR_GTX_N). Since
there are some minor differences between GTH3 and GTH4 that software needs
to know about rename the GTH_OR_GTX_N to XCVR_TYPE and match use the same
semantics as util_adxcvr.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The external s_axi_{awaddr,araddr} signals that are connect to the core
have their width set according to the specified size of the register map.
If the s_axi_{awaddr,araddr} signal of the core is wider (as it currently
is for many cores) the MSBs of those signals are left unconnected, which
generates a warning.
To avoid this make sure that the signal width matches the declared register
map size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
When using non-broadcast access to the GT DRP registers lane filtering is
done on both sides. The ready and data signals are filtered in the in the
axi_adxcvr module and the enable signal is filtered in the util_adxcvr
module. This works fine as long as both sides use the same transceiver IDs.
E.g. channel 0 of the axi_adxcvr module is connected to channel 0 of the
util_adxcvr module.
But this is not always the case. E.g. on the ADRV9371 platform there are
two RX axi_adxcvr modules (RX and RX_OS) connected to the same util_adxcvr.
The first axi_adxcvr uses lane 0 and 1 of the util_adxcvr, the second uses
lane 2 and 3.
Non-broadcast access for the first RX axi_adxcvr module works fine, but
always generates a timeout for the second axi_adxcvr module. This is
because lane 0/1 of the axi_adxcvr module is connected to lane 2/3 of the
util_adxcvr and when ID based filtering is done both can't match at the
same time.
To avoid this perform the filtering for all the signals in the axi_adxcvr
module. This makes sure that the same base ID is used.
This also removes the sel signal from the transceiver interfaces since it
is no longer used on the util_adxcvr side.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the scripts use 'analog.com' as the vendor property for IP cores,
but 'ADI' for interfaces.
Make things consistent by using 'analog.com' for both interfaces as well
as IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
- Change the clock and reset port name of the AXI slave interface
to s_axi_aclk and s_axi_aresetn. This way we can use the adi_ip_properties
process to infer the interface.
- Define an address space reference to the m_axi interface.
Laszlo Nagy
Arpadi
Istvan Csomortani
AndreiGrozav
Adrian Costina
Lars-Peter Clausen
Rejeesh Kutty
Shrutika Redkar