The cores that handle the JESD204 ADC cores do not feature IQ correction
logic. The Q_OR_I_N parameter for the channel modules is unused, so remove
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The cores that handle the JESD204 ADC converters do not feature any direct
IO and subsequently no IO-delay blocks either. Remove the unused
IO_DELAY_GROUP parameter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Bundle the TLAST signal in with the other AXIS slave signals to enable
easier connection between AXIS devices that use TLAST
Signed-off-by: Matt Fornero <matt.fornero@mathworks.com>
Add some limit TLAST support for the streaming AXI source interface. An
asserted TLAST signal marks the end of a packet and the following data beat
is the first beat for the next packet.
Currently the DMAC does not support for completing a transfer before all
requested bytes have been transferred. So the way this limited TLAST
support is implemented is by filling the remainder of the buffer with 0x00.
While the DMAC is busy filling the buffer with zeros back-pressure is
asserted on the external streaming AXI interface by keeping TREADY
de-asserted.
The end of a buffer is marked by a transfer that has the last bit set in
the FLAGS control register.
In the future we might add support for transfer completion before all
requested bytes have been transferred.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Commit ff50963c7f ("axi_ad9361- altera/xilinx reconcile- may be broken-
do not use") inverted the polarity of the TX feedback clock.
This exposed some issues in the existing drivers which can cause the
interface tuning to fail randomly under certain conditions.
To keep backwards compatibility with existing drivers restore the previous
behavior.
A separate fix will be applied to the drivers that resolves the issue that
has been exposed by the polarity inversion. So that interface calibration
works reliably under all conditions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Assigning the value of a local parameter(localparam) to a parameter
will end up with a conflict(not highlighted by the tool). In this
case, the parameter type was defined as a string instead of an
integer. Furthermore, this scenario leads to an undesired choice
between primitive types.
The dma_last_beats is used by the Avalon Memory Mapped interface
controller, to define the last burst length.
Its value get stable after the last valid data of the DMA interface, and staying
stable until the positive edge of the DMA's xfer_req.
No need to condition the transfer of this register to avalon clock
domain.
The XFER_END state defines the end of a transaction, when the entire
data set is written or read to/from the DDRx memory.
A transaction can contain multiple Avalon bursts. Make sure that the FSM
goes back into staging phase at the end of each burst; also define a
signals which indicate the end of each burst for control.
The period_count should be updated once per clock cycle. This is not
enforced with the current implementation, which probably leads to
period_count being decremented on both m_axis_aclk edges.
A problem observed due to this is that the m_axis_tlast output is not
asserted or is asserted for a too short time for the consumer to
detect it.
Fix by letting the decrement (and thus the m_axis_tlast toggling)
happen only on the rising edge of the m_axis_aclk clock.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
The commit 6900c have added an additional register stage into the fifo read
data path, but the control signals (ready/valid/underflow) were not realigned
to the data. This can cause data lose or duplicated samples in some case.
Realign the control signals to the data.
The util_adxcvr supports GTX2, GTH3 and GTH4. The transceiver is selected
using the XCVR_TYPE parameter.
The axi_adxcvr on the other hand only has a configuration parameter to
indicate whether a GTX or GTH transceiver is used (GTH_OR_GTX_N). Since
there are some minor differences between GTH3 and GTH4 that software needs
to know about rename the GTH_OR_GTX_N to XCVR_TYPE and match use the same
semantics as util_adxcvr.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The dac_xfer_req should indicate one single thing, that the FIFO is in
read phase. Should not be affected by any signals, which indicates data
validity on any interface. (e.g. dac_valid)
This signal is not used by the device core, its main purpose is to
indicate the state of the interface for a posible intermediat processing
module.
Fix the reset of the dma_mem_waddr (write address register of the CDC
FIFO on DMA's clock domain). This solves the occasional invalid read backs after
multiple re-initialization of the PL_DDR_FIFO.
+ Build both the read and write logic around an FSM
+ Consistent naming of registers and wires
+ Add support for burst lenghts higher than one, current burst lenght
is 64
+ Fix all the bugs, and make it work (first bring up with
adrv9371x/a10soc)
If the ADI_HDL_DIR or ADI_PHDL_DIR are set on Windows platforms, an
invalid TCL character (e.g. backslash) may be used as a file separator,
causing issues with the build / library scripts.
Normalize the paths before using them as global TCL variables.
The first attempt (f3daf0) faild miserably. When the data_req signal
from the device had more than 1 cycle of deassert state, because of the
added latency of the data stream, the device got 'zeros' too.
In this fix, the DMA will hold the valid data on the bus, between two
consecutive data request. The bus is reseted just after all the data
were sent out.
The grey coder/decoder function was limited to 10 bits, and this
resulted an unwanted limitation of the FIFO size. Using this
module, the coder/decoder data width can be adjusted to the current
address width.
Reset the fifo_rd_data if the DMA does not have an active transfer.
Becasue all the DAC device cores are transfering the data from the FIFO
interface to the data interface without any validation signal, DMA needs to put
the data bus into a known state, to prevent the device core to send the
last known data again and again.
Add missing timing exceptions on paths between the DMA and DDR clock
domains. All these paths are properly synchronized using CDC in the HDL,
but are missing timing exceptions in the XDC file. This can lead to timing
errors when building a design using the axi_adc_fifo.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Adrian Costina
Istvan Csomortani
Lars-Peter Clausen
AndreiGrozav
Matt Fornero
Luca Ceresoli
Rejeesh Kutty