9ee0f09078
daq3:qsys: Activate input pipeline stage for AD9680's JESD interface
2020-09-09 14:15:37 +03:00
c8e0a1ec04
projects: adrv9009: intel: Update JESD204 LANE_RATE and REFCLK_FREQUENCY
...
To match the Linux default setup.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
2020-09-09 14:15:37 +03:00
61ece1f1e9
s10soc: Insert an additional bridge between DMA and HPS
...
Due to the interface differences between HPS's AXI4 and DMA's AXI4, the
tool will try to automaticaly add some bridges between the two
interface. Unfortunatly it does generate timing issues at the f2sdram0
interface of the HPS instance. By explicitly instantiating an AXI
bridge, these timing issues disappears.
2020-09-09 14:15:37 +03:00
46b6bf8f8a
adrv9009/qsys: input pipline active for jesd204_rx and jesd204_rx_os
2020-09-09 14:15:37 +03:00
5a8f277253
adrv9009/s10soc: Add support for Stratix10 SOC
2020-09-09 14:15:37 +03:00
2b5136db98
scripts/project_intel.mk: Update CLEAN targets
2020-09-09 14:15:37 +03:00
eb8e1142cd
adrv9009/intel: Fix the register address layout
...
The reconfiguration interface for the Stratix10 XCVR has a different
address width. Prepare the register map layout of the project to support
this new architecture.
2020-09-09 14:15:37 +03:00
8818089015
a10soc: Reconfiguration interface address width improvement
...
The reconfiguration interface's address width is different in various
architectures. Define the required address width in system_qsys.tcl.
2020-09-09 14:15:37 +03:00
91b199a907
s10soc: Add new feature for ad_cpu_interconnect
...
If we have a lot of peripherals connected to the CPU's memory interface,
the generated interconnect can grow to much decreasing the timing
margin.
One solution is to group the peripherals by its interface types and
functions and use bridges to connect them to the memory interface.
This commit adds the possibility to insert an Avalon Memory Mapped
bridge when we create the connection between the peripheral and CPU.
Should be used just with Avalaon Memory Mapped interfaces.
2020-09-09 14:15:37 +03:00
f9c4283f45
stratix10soc: Initial commit of base design
...
Note: Currently we have a engineering sample version 2 board.
2020-09-09 14:15:37 +03:00
24090fafd8
adrv9001/zcu102: Loopback VADJ error to the FMC board
2020-08-31 14:14:03 +03:00
d14376547f
adrv9001/zed: Refactor VADJ test in VADJ error
...
The ADRV9002 uses in the digital interface 1.8V, however the Zed VADJ is
selectable by a jumper can go up to 3.3V . Voltage levels higher than 1.8V
are detected by the EVAL-ADRV9002 board, asserting the VADJ_ERR pin.
If VADJ error is set high keep all drivers in high-z state and signalize
it to the software layer through a gpio line.
2020-08-31 14:14:03 +03:00
72f916fcf5
adrv9001/zcu102: Update interface signal names based on direction
...
Let the names of signals from source synchronous interface match the
direction of the signals.
2020-08-28 13:23:00 +03:00
a212ad6e58
adrv9001/zed: Update interface signal names based on direction
...
Let the names of signals from source synchronous interface match the
direction of the signals.
2020-08-28 13:23:00 +03:00
eb2f211d30
scripts/intel: Add message severity definition file
2020-08-25 14:46:52 +03:00
9c4df588bb
fmcomms2: a10soc remove project
...
Starting from Quartus 18.1 the project won't build as LVDS SERDES needs to be
driven by a dedicated reference clock pin and A10SOC doesn't have dedicated pins
routed at the _CC FMC location.
Prior to version 18.0 this was reported as a critical warning.
See https://community.intel.com/t5/Intel-Quartus-Prime-Software/LVDS-SERDES-reference-clock-enforcement-change-in-18-1/td-p/196078
2020-08-25 14:19:48 +03:00
118e1f9e8b
adrv9001/zed: Initial support for Zed
...
CMOS only support for ADRV9001 on ZedBoard
2020-08-24 17:49:12 +03:00
b27f3ac18f
adrv9001:zcu102: Initial version
...
Generic project that supports CMOS or LVDS interface for the ADRV9001 transceiver.
2020-08-24 17:49:12 +03:00
d8c98c9904
cn0540/coraz7s: Relax timing in SPI Engine
2020-08-24 16:45:02 +03:00
fa0b39fa20
adi_project_intel: Update QSYS generation
...
In Quartus Prime in place of the set_domain_assignment command, the
set_interconnect_requirement command is used.
2020-08-17 12:02:49 +03:00
b54effc9c9
daq2/a10gx: Set optimization mode to aggressive performance
2020-08-17 10:43:03 +03:00
fb7da01498
adrv9371x/a10gx: Set optimization mode to aggressive performance
2020-08-17 10:43:03 +03:00
738f7af23b
ad40xx_fmc: SDI delay should be set to 1
...
In general we have to add a delay of half SCLK cycle.
(latch the MISO on the next consecutive SCLK edge)
2020-08-13 10:01:16 +03:00
4766d01915
m2k: Update constraints
2020-08-13 07:01:19 +03:00
4d39a3595f
m2k: Connect signals for instrument sync
2020-08-13 07:01:19 +03:00
f3b69c15c9
scripts/intel: Update version check
2020-08-12 10:33:29 +03:00
218f45a0df
scripts/intel: Set supported Quartus version to 19.3
2020-08-12 10:33:29 +03:00
62eb5a067d
fmcomms2/a10soc: Unused outputs should be left hanging
2020-08-11 10:14:18 +03:00
a66029aef3
adrv9009/a10gx: Delete redundant timing constraints
2020-08-11 10:14:18 +03:00
02ada3bbf7
a10gx: Delete input/output delay definitions
...
All input and output delays should be referenced to a virtual clock.
If the input and output delays reference base clocks or PLL clocks rather than
virtual clocks, the intra- and inter-clock transfer clock uncertainties,
determined by derive_clock_uncertainty, are incorrectly applied to the I/O ports.
See mnl_timequest_cookbook.pdf for more info.
2020-08-11 10:14:18 +03:00
f1a0946a5d
daq3: Delete redundant timing constraint
...
Delete none generic timing constarints related to the memory interface.
Set optimization mode to default.
2020-08-11 10:14:18 +03:00
1c907b9248
daq2/a10gx: Use the default optimization mode
2020-08-11 10:14:18 +03:00
9043f3737b
Revert "a10gx: Optimise the base design"
...
This reverts commit 9afc871b70
2020-08-11 10:14:18 +03:00
4af0c98c56
a10gx: Fix exceptionSlave interface definition for HPS
2020-08-11 10:14:18 +03:00
5ba3448987
scripts/project-intel: Update CLEAN target
2020-08-11 10:14:18 +03:00
0b51c474a1
a10gx: Add a Avalon Pipeline Bridge between EMIF and DMA's
2020-08-11 10:14:18 +03:00
6d19041b21
dac_fmc_ebz: QPRO is using apply_instance_preset
2020-08-11 10:14:18 +03:00
0de5039b96
avl_dacfifo: add_intance command must have a version attribute
2020-08-11 10:14:18 +03:00
8fd1ad64d6
quartus: Increase tool version to 19.2
2020-08-11 10:14:18 +03:00
f3142a6a7a
adi_project_intel: set_interconnect_requirment command is deprecated
...
Use set_domain_assignment to set up the maximum pipeline stages for the
main interconnect.
2020-08-11 10:14:18 +03:00
a39fa831d0
ad9371:a10gx: Relax interconnect requirements
2020-08-11 10:14:18 +03:00
7e22f91429
adrv9371:a10gx: Remove constraint from DDR
2020-08-11 10:14:18 +03:00
359e5d94ec
a10gx: Remove constraint from eth_ref_clk
2020-08-11 10:14:18 +03:00
967a138d0f
adi_project_intel: Add support for Quartus Pro
...
By defualt the supported tool chain is Quartus PRO. If you want to
build the project with Quartus Standard, you need to define an environment
variable called QUARTUS_PRO_ISUSED with the value 0. (e.g. export
QUARTUS_PRO_ISUSED=0 )
Note: Not all projects going to build on Quartus Standard, you should
fix the errors if there is any.
2020-08-11 10:14:18 +03:00
054193e083
adi_project_intel: Delete all MESSAGE_DISABLE assignment
...
These kind of assignments should be placed into file like
~/projects/scripts/adi_xilinx_msg.tcl
2020-08-11 10:14:18 +03:00
4ca1311d57
quartus_pro: Global assignment ENABLE_ADVANCED_IO_TIMING is not supported
2020-08-11 10:14:18 +03:00
8d6b8fc631
Add cn0506_rmii/zcu102 support on revB
2020-08-10 18:32:44 +03:00
7e96514230
Add cn0506_rmii/zc706 support on revB
2020-08-10 18:32:44 +03:00
321b82398b
Add cn0506_rmii/zed support on revB
2020-08-10 18:32:44 +03:00
6c2b1b1634
fmcomms5/zc702: Fix the sys_dma_clk connections
2020-06-19 12:53:18 +03:00
Istvan Csomortani
Dragos Bogdan
Laszlo Nagy
Adrian Costina
AndreiGrozav