Running 'make' will build the default project directly in the project folder (like it did before)
Running 'make RX_LANE_RATE=15 TX_LANE_RATE=15' will build the project inside the 'RXRATE15_TXRATE15' subdirectory.
Running 'make CFG=cfg/test_config.txt" will use the variables found inside the configuration file and build the project inside the 'test_config' subdirectory.
Running 'make clean' will clean the default project only.
Running 'make CFG=cfg/test_config.txt clean' will clean the 'testconfig' build.
Running 'make clean-all' will delete all the built configurations and libraries.
Note that the 'JESD' and 'LANE' words from the parameter names are stripped.
Signed-off-by: Bogdan Luncan <bogdan.luncan@analog.com>
New version of Quartus Standard for de10nano and sockit was changed
to 21.1.
Signed-off-by: Liviu Adace <liviu.adace@analog.com>
Signed-off-by: Liviu Adace <liviu.adace@analog.com>
Deleted lines after endmodule and consecutive empty lines.
Modified parentheses, extra spaces.
Fixed indentation.
Fixed parameters list to be each parameter on its line.
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
This adds a Readme.md to each project directory with pointers to project
documentation in the wiki, and the drivers (if they exist). This will
help with some autogenerated doc in the wiki, that is generated with the
innovatily named "wiki_summary.sh" shell script that parses through
these Readme.md files, and generates a summary table.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Iacob Liviu Mihai <liviu.iacob@analog.com>
Without defining this signal, the UART lines receive garbage data
when no cable is connected to the J4 USB UART port.
The GPIO9 is enabled in the reference base design along with the
4MA CURRENT_STRENGTH constraint on the UART pins
-change the video memory interfacing from f2h_axi_slave to
f2h_sdram0
- add f2h_sdram1 port as the default interface for converter DMA
- set as default the full HD resolution at 60 FPS (pixel clock 148.5MHz)
- use a second 200MHz(198MHz) clock from the pixel_clk_pll, as DMA source
to destination clock.
The coraz7s has an Arduino/chipKIT Shield connector with 6 Single-ended
and 8 Differential Analog inputs tied to Xilinx's XADC.
The CN0540 uses the A0-5 pins as single-ended ADC channels to monitor
the differential input, ADC driver, and buffer voltages.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Note, the current SCLK to spi_clk ratio is four. That means, the input
delay in the MISO line is 25% of the SCLK period.
If the SCLK to spi_clk ratio is changing, this constraint must be
updated.
Generate a higher frequency of spi_clk using an axi_clkgen. (MMCM)
CAUTION: ad7768-1 is still violating the standard SPI timing,
reducing the timing window significantly for the last bit (or last high
bit).
Ignore the following critical warning on DMAC instance:
Critical Warning (15003): "mixed_port_feed_through_mode" parameter of RAM atom
system_bd:i_system_bd|axi_dmac:axi_dmac_0|axi_dmac_transfer:i_transfer| \
dmac_request_arb:i_request_arb|dmac_dest_mm_axi:i_dest_dma_mm| \
altsyncram:bl_mem_rtl_0|altsyncram_0tp1:auto_generated|ram_block1a1
cannot have value "old" when different read and write clocks are used.
Iulia Moldovan
ladace
Sergiu Arpadi
Bogdan Luncan
PopPaul2021
Iacob_Liviu
Adrian Costina
Robin Getz
Laszlo Nagy
AndreiGrozav
Istvan Csomortani
Sergiu Cuciurean
Stanca Pop