TCL files can be helpful to automate certain tasks like creating timing
constraints. Add handling for them to the ad_ip_addfile function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the reset for the link clock domain is generated internally in
the axi_jesd204_{rx,tx} peripheral. The reset is controlled by through the
register map.
Add an additional external reset for link clock domain. The link clock
domain is kept in reset if either the internal reset or the external reset
is asserted.
This for example allows the fabric to keep the domain in reset if the clock
is not yet stable.
The status of the external reset can be queried from the register map.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
dma_raddr is only incremented if it is less than dma_waddr_rel_s.
dma_waddr_rel_s is always less or equal to adc_waddr_rel << RATIO and
adc_waddr_rel is less than DMA_ADDR_LIMIT >> RATIO.
By induction we can conclude that this means that dma_raddr will always be
less then DMA_ADDR_LIMIT and the check for this will always evaluate to
false can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
When the DMA clock to ADC data rate ratio exceeds a certain threshold it is
possible that an erroneous dma_waddr_rel toggle event is generated. This
causes the last address of the previous DMA transfer to be transferred to
the DMA domain. And the DMA side will start reading from the FIFO even
though data is not available yet.
This results in data corruption with the current transfer containing data
from the previous transfer.
The root cause here is that the toggle signal CDC synchronizer register are
reset in the DMA when a new transfer starts, but not in the ADC domain,
causing a potential mismatch and the incorrect toggle event. To fix this
remove the reset from the DMA side. This is OK since the registers are
self-resetting if the reset signal is asserted for more than 3 clock cycles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
AND logic means that all enabled triggers need to evaluate to true, others
are don't care. Fix the logic to behave accordingly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
At the moment the drain signal is always asserted when the controller is
enabled. This breaks backpressure and data is lost. The drain signal should
only be asserted when the controller gets disabled until the last beat of
the current DMA transfer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The 'PRIMITIVE_SUBGROUP == flop' filter only works on 7-Series. Replace it
with 'IS_SEQUENTIAL' which works on both 7-Series and UltraScale.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
In its default configuration the ram_2port module as a read latency of 2
clock cycles. Both the read address as well as the output data are
registered.
This is not the behavior that is expected from the alt_mem_asym module and
causes incorrect behavior and data corruption in the util_adc_fifo.
Disable the data output register to get a read latency of 1 clock cycle.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Name all CDC blocks following the patter i_cdc_${signal_name}. This makes
it clear what is going on.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Use the CDC sync_bits helper to synchronize the asynchronous external SYNC~
signal into the link clock domain, rather than open-coding this operation.
This makes it more explicit what is going on.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Which events will be exposed as IRQs and at what level of granularity will
need some additional through. Remove the two existing IRQ events for now
again. This will be added back later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The up_cfg_ilas_data signal is a two dimensional array. There are 4
register entries for each lane. Model it as such rather than compressing it
down to a one dimensional array. This makes accessing the individual
entries a bit more straight forward and the code clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The ilas_cfg_static.v is part of the jesd204_tx_static_config module.
Somehow a copy of that file made it into the jesd204_tx module where it is
completely unused. Remove the duplicated file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
We know that NUM_OF_LANES will never exceed 255, but the tools don't know
and generate a warning about implicit signal truncation. Make the
truncation explicit to indicate that this is intentional.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DDR memory reference clock on the A10SoC development board is
differential. Currently the EMIF core it is configured for single-ended
configuration, which causes it to generate incorrect IOSTANDARD
constraints. Those incorrect constraints get overwritten again in
system_assign.tcl, so things are working, but this generates a warning when
building the design
Configure the EMIF core correctly and remove the manual constraint overwrite since
they are no longer necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
+ update to verilog-2001 coding standard
+ define RATIO outside the generate block
+ $clog2 macro is not supported by some tools, define function
locally
The CIC filter introduces different amplifications depending on the
decimation ratio. By adding a multiplier in the decimation chain
the amplification can be compensated
There is no guarantee that the external reset de-assertion is synchronous
to the sys_clk, yet the clock bridge marks the reset de-assertion as
synchronized to the clock. This can cause recovery or removal timing
violations for the registers affected by this reset signal and potentially
bring the system into an invalid state after the reset is de-asserted.
Mark the reset as not synchronized to the clock signal, this will make sure
that Qsys inserts the proper reset synchronizers where required.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The ADI transport layer peripherals expect the first octet to be in the
LSBs and the last octet to be in the MSBs. The Altera JESD204 core orders
the octets the other way around though, first octet in the MSBs and last
octet in the LSBS.
Currently this is handled by having each transport layer peripheral swap
the octets around when it is connected to the Altera JESD204 core.
Change this so that rather than having to do the data swizzling in every in
every transport layer peripheral perform it at the input/output of the link
layer peripheral inside the generated block.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the TX lane mapping is implemented by having to connect tx_phy_s_* to
the tx_ip_s_* and the tx_phy_d_* to the tx_ip_d_* signals in the system
qsys file in the desired order.
Re-work things so that instead the lane mapping is provided through the
TX_LANE_MAP parameter. The parameter specifies in which order logical lanes
are mapped onto the physical lanes.
The appropriate connections are than made inside the core according to this
parameter rather than having to manually connect the signals externally.
In order to generate a 1-to-1 mapping the TX_LANE_MAP parameter can be left
empty.
This change slightly reduces the boiler-plate code that is necessary to
setup the transceiver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Lars-Peter Clausen
Istvan Csomortani
Rejeesh Kutty
Adrian Costina