On architectures with ports that support cache coherency, the AWCACHE
signal must be set to indicate that transactions are cached. This patch
adds a parameter allowing AWCACHE to be set on an AXI4 destination port.
FPGAs support different widths for the read and write port of the block
SRAM cells. The DMAC can make use of this feature when the source and
destination interface have a different width to up-size/down-size the data
bus.
Using memory cells with asymmetric port width consumes the same amount of
SRAM cells, but allows to bypass the re-size blocks inside the DMAC that
are otherwise used for up- and down-sizing. This reduces overall resource
usage and can improve timing.
If the ratio between the destination and source port is too larger to be
handled by SRAM alone the SRAM block will be configured to do partial up-
or down-sizing and a resize block will be inserted to take care of the
remaining up-/down-sizing. E.g. if a 256-bit interface is connected to a
32-bit interface the SRAM will be used to do an initial resizing of 256 bit
to 64 bit and a resize block will be used to do the remaining resizing from
64 bit to 32 bit.
Currently this feature is disabled for Intel FPGAs since Quartus does not
properly infer a block RAM with different read and write port widths from
the current ad_asym_mem module. Once that has been resolved support for
asymmetric memories can also be enabled in the DMAC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DMA_LENGTH_ALIGN LSBs of all length For the most part the tools are
able to deduce this using constant propagation.
But this propagation does not work across the asynchronous meta data FIFO
in the burst memory module.
Add a DMA_LENGTH_ALIGN parameter to the burst_memory module which is used
to explicitly keep the LSBs of length registers on the destination side
fixed at 1'b1. This reduces resource use and improves timing by allowing
better constant propagation and unused logic elimination.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
For consistent simulation behavior it is recommended to annotate all source
files with a timescale. Add it to those where it is currently missing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Length of partial transfers are stored in a queue for SW reads.
The presence of partial transfer is indicated by a status bit.
The reporting can be enabled by a control bit.
The progress of any transfer can be followed by a debug register.
In MM2S applications like video DMA it is useful to mark the end of the stream
with the TLAST.
The change enables the generation of the TLAST on the last beat of the
last row of the 2d transfer.
The index on MSB of addresses was set to 31,
but the width of address in the axi_dmac depends on a parameter.
The mismatch causes issues in the Xilinx simulator which does not extends the
narrower width signal with zeros, instead the wider signal gets 'Z' on its MSBs.
When the address was incremented with the stride it became 'X' due the uninitialized
MSBs.
This change adds a diagnostic interface to the DMAC core.
The interface exposes internal information about the core,
information which can't be exposed through AXI registers
due the latency and update rate.
Such information is the fullness of the internal buffer.
For this is exposed in bursts and is driven from the destination
clock domain, as this is reflected in its name.
The signal has a fixed size and is dimensioned by
taking in account the supported maximum number of bursts of 128.
For the memory-mapped AXI read interface the slave asserts rlast for the
last beat in a burst.
This means we don't have to count the number of beats to know when the
burst is completed but instead can use rlast. This slightly reduces the
amount of resources needed for the MM-AXI source module and given that the
beat_counter is often the bottleneck timing wise this should also improve
the timing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DMAC allows a transfer to be aborted. When a transfer is aborted the
DMAC shuts down as fast as possible while still completing any pending
transactions as required by the protocol specifications of the port. E.g.
for AXI-MM this means to complete all outstanding bursts.
Once the DMAC has entered an idle state a special synchronization signal is
send to all modules. This synchronization signal instructs them to flush
the pipeline and remove any stale data and metadata associated with the
aborted transfer. Once all data has been flushed the DMAC enters the
shutdown state and is ready for the next transfer.
In addition each module has a reset that resets the modules state and is
used at system startup to bring them into a consistent state.
Re-work the shutdown process to instead of flushing the pipeline re-use the
startup reset signal also for shutdown.
To manage the reset signal generation introduce the reset manager module.
It contains a state machine that will assert the reset signals in the
correct order and for the appropriate duration in case of a transfer
shutdown.
The reset signal is asserted in all domains until it has been asserted for
at least 4 clock cycles in the slowest domain. This ensures that the reset
signal is not de-asserted in the faster domains before the slower domains
have had a chance to process the reset signal.
In addition the reset signal is de-asserted in the opposite direction of
the data flow. This ensures that the data sink is ready to receive data
before the data source can start sending data. This simplifies the internal
handshaking.
This approach has multiple advantages.
* Issuing a reset and removing all state takes less time than
explicitly flushing one sample per clock cycle at a time.
* It simplifies the logic in the faster clock domains at the expense of
more complicated logic in the slower control clock domain. This allows
for higher fMax on the data paths.
* Less signals to synchronize from the control domain to the data domains
The implementation of the pause mode has also slightly changed. Pause is
now a simple disable of the data domains. When the transfer is resumed
after a pause the data domains are re-enabled and continue at their
previous state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Move the transfer logic, including the 2d module, into its own sub-module.
This allows testing of the full transfer logic independently of the
register map logic.
The top-level module now only instantiates the register map and transfer
module, but does not have any logic on its own.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Mathias Tausen
Iulia Moldovan
Lars-Peter Clausen
Laszlo Nagy