75b965e87f
ad9081_fmca_ebz/zcu102: Enable 204C modes
2021-06-10 09:53:43 +03:00
6637436c2e
scripts/adi_board.tcl: Use div2 out clock from xcvr in case of GTH and 204C
2021-06-10 09:53:43 +03:00
27465ce9c0
ad9081_fmca_ebz/zcu102: Fix spaces
2021-06-10 09:53:43 +03:00
7b7609d21a
ad469x: Clean system_project.tcl
2021-06-03 15:41:58 +03:00
d9bc014c98
adrv9001/zcu102: Enable independent Tx from Rx in CMOS mode
2021-05-26 15:44:45 +03:00
568bef4a38
adrv9001/a10soc: Initial version
...
This project supports CMOS mode only.
2021-05-26 15:44:45 +03:00
5d008c3eca
Correct constraints file pin mapping
2021-05-25 16:27:58 +03:00
0ad691a603
ad9081_fmca_ebz/zcu102: Differentiate parameters based on lane rate
2021-05-14 15:39:40 +03:00
8183599b51
ad9081_fmca_ebz/zcu102: Fix typo
2021-05-14 15:39:40 +03:00
cf7f45ffcc
ad9081_fmca_ebz: Fix for F=8
2021-05-14 15:39:40 +03:00
7b2ba41bdd
ad9081_fmca_ebz/vcu118: Adjust QPLL params and diff swing
...
This commit fixes the 16.5Gbps lane rate case where the link drops
after few seconds an initial successful link up happens.
A few seconds delayed calibration process can workaround this but with
having the differential drivers swing increased this is no longer
required.
2021-05-14 15:39:40 +03:00
eba3409d78
ad9082_fmca_ebz: Use 9081 system_bd, updated comments
2021-05-14 15:39:40 +03:00
0d9e38bdbe
ad9081_fmca_ebz: Update path to common block design
...
Use absolute paths so ad9082 wrapper project can include the
system_bd.tcl instead of duplicating code.
2021-05-14 15:39:40 +03:00
680d28476c
ad9081_fmca_ebz: Add LANE_RATE param to all projects
...
The block design expects a lane rate to be set in the system project.
2021-05-14 15:39:40 +03:00
bd6ec360e2
ad9081_fmca_ebz/vcu118: Set XCVR params for 204C link
...
Set XCVR parameter for 204C 24.75 Gbps with a dynamic range of 10Gbps..24.75Gpbs
Organize XCVR params based on lane rate
2021-05-14 15:39:40 +03:00
693c002668
ad9081_fmca_ebz/common/ad9081_fmca_ebz_bd: Add 204C support for XCVR
...
Remove Xilinx PHY and simplify project
2021-05-14 15:39:40 +03:00
d92f925b06
ad9081_fmca_ebz: Disable XBAR from DAC TPL
2021-05-14 15:39:40 +03:00
77a5edaa83
scripts/adi_board.tcl: In 204C do not connect SYNC
...
Take link mode parameter from util_adxcvr, check it against the axi_adxcvr.
2021-05-14 15:39:40 +03:00
1db04a47b8
ad9083_evb: Update parameters to 10Gpbs lane rate
2021-04-19 13:21:34 +03:00
8335e1bd9a
sysid: Make sure gitbranch_string is always declared
...
Parsing of not existed "gitbranch_string" fails the build process.
2021-03-24 13:34:32 +02:00
6a374ef457
ad469x/zed: Add multicycle path constraint
2021-03-22 13:05:05 +02:00
40baa63f0f
adrv2crr_fmcomms8: Fix system_top.v
2021-03-19 17:56:28 +02:00
a1773c661c
adrv9009zu11eg_crr: Update spi
...
Add two more CS signals to P25 connector
2021-03-10 10:53:11 +02:00
3dce87d09b
ad9083: Add reference design for ad9083 eval board
2021-03-10 10:52:03 +02:00
dcec4fe1b7
adrv9001/zc706: Fix spaces
2021-03-10 10:35:52 +02:00
dc186645d8
adrv9001/zc706: Fix comments HPC to LPC
2021-03-10 10:35:52 +02:00
4a772265a9
Update Quartus Prime version from 19.3.0 to 20.1.0
...
adi_project_intel.tcl: Change quartus version to 20.1.0.
library: Set qsys version so that IP instances won't require a specific version.
2021-03-08 11:29:33 +02:00
1099badaf4
ad9082_fmca_ebz:zc706: Initial version
2021-03-05 15:54:23 +02:00
2213527f29
ad9082_fmca_ebz:zcu102: Initial version
2021-03-05 15:54:23 +02:00
f56e3c305b
ad9082_fmca_ebz:vcu118: Initial version
2021-03-05 15:54:23 +02:00
6b13b32f24
ad9081_fmca_ebz: Workaround DMA bug when bus size equals max burst size
2021-03-04 11:13:29 +02:00
677c154134
adrv9001/zcu102/cmos: Loosen up clock skew constraints to match LVDS settings
...
Set the same inter clock skew characteristics as used in LVDS mode. The
physical lanes/routes are common on both modes.
2021-03-04 11:13:10 +02:00
03de08609b
fmcomms2/zed: Disable unused TDD to save space and timing
2021-03-04 11:13:10 +02:00
0dd3173547
adrv9001/zc706: Initial commit
...
The project supports CMOS interface only.
VADJ on the ZC706 must be programmed to 1.8V
Instructions can be found here:
https://www.xilinx.com/Attachment/ZC706_Power_Controllers_Reprogramming_Steps.pdf
https://forums.xilinx.com/t5/Xilinx-Evaluation-Boards/ZC706-Doesn-t-work-with-VADJ-at-1-8v/td-p/430086
2021-03-03 09:03:03 +02:00
3be5137aec
cn0540/cora: Remove multicycle constraint
...
Design uses 80MHz spi_clk which does not require
special considerations
2021-02-18 14:14:16 +02:00
701e5f6515
scripts/adi_board.tcl: Add simulation support
...
This will allow building base test harnesses and place on top of them
existing block designs for simulation purposes.
Test harnesses will contain basic functionality like
- clock and reset generators
- AXI master to aid register access of the cores.
- memory model of the DDR
- interrupt controller
Existing procedures (ad_mem_hp0_interconnect, ad_cpu_interconnect, ... ) will
connect to this harness as they do to a real base design.
2021-02-12 16:21:10 +02:00
0374a7c1ac
ad9081_fmca_ebz/vcu118: Added common 204C use cases as example
2021-02-05 15:24:15 +02:00
ddd8a14790
ad9081_fmca_ebz: Remove system reset from Xilinx PHY
...
Reset in device clock domain caused timing failures.
Since link reconfiguration is not supported the reset is not required.
2021-02-05 15:24:15 +02:00
af3e1c7003
ad9081_fmca_ebz/a10soc: Np 12 support
2021-02-05 15:24:15 +02:00
f73ed741c9
fmcadc5: Connect link clock to second JESD link layer
2021-02-05 15:24:15 +02:00
3f2f88ebbc
ad_fmclidar1_ebz: Set bits per sample towards the DMA interface
2021-02-05 15:24:15 +02:00
dafdd1c1e9
ad9208_dual_ebz: Use ad_xcvrcon procedure to connect device clock
2021-02-05 15:24:15 +02:00
bb9eafceef
ad9081_fmca_ebz/zcu102: Add case analysis to select correct out clock frequency
2021-02-05 15:24:15 +02:00
d0f8a81b2f
ad9081_fmca_ebz: Np 12 support
...
204B functional
204C functional
2021-02-05 15:24:15 +02:00
454b900f90
jesd204: Xilinx: NP=12 support
...
To support deterministic latency with non-power of two octets per frame
(F=3,6) the interface width towards the transport layer must be resized
to match integer multiple of frames.
e.g Input datapath width = 4; Output datpath width = 6;
for F=3 one beat contains 2 frames
for F=6 one beat contains 1 frame
The width change is realized with a gearbox.
Due the interface width change the single clock domain core is split
in two clock domains.
- Link clock : lane rate / 40 for input datapath width of 4 octets 8b10b
- lane rate / 20 for input datapath width of 8 octets 8b10b
- lane rate / 66 for input datapath width of 8 octets 64b66b
- Device clock : Link clock * input data path width / output datapath width
Interface to transport layer and SYSREF handling is moved to device clock domain.
The configuration interface reflects the dual clock domain.
If Input and Output datapath width matches, the gearbox is no longer
required, a single clock can be connected to both clocks.
2021-02-05 15:24:15 +02:00
7be66b63c1
adrv9009zu11eg:fmcomms8: Fix lane swapping for TX channels 0 and 1 on the FMCOMMS8
2021-02-05 15:07:09 +02:00
6d504d14cf
fmcomms8: zcu102: Fix lane swapping
2021-02-05 15:07:09 +02:00
0fd5590e56
ad9081_fmca_ebz: a10soc: Initial version
...
Parametrizable project with default profile of:
M=8 L=4 SampleRate=250 MSPS
LaneRate=10 Gbps
2021-02-05 10:24:59 +02:00
6e6c51dd27
common/a10soc: Bridge support
2021-02-05 10:24:59 +02:00
f0b753321a
common/intel: Add util_adcfifo integration script
2021-02-05 10:24:59 +02:00
Laszlo Nagy
sergiu arpadi
Owen McAree
vladimirnesterov
stefan.raus
Adrian Costina
Istvan Csomortani