189e9194c8
m2k: Standalone, enabled power optimization
2017-04-18 12:17:40 +02:00
8b76c34dea
scripts: Created ADI_POWER_OPTIMIZATION parameter for enabling power optimizations in the implementation stage
2017-04-18 12:17:40 +02:00
07e52b4566
m2k: Connect logic_analyzer path to clk_out instead of clk
...
- this allows for the clock switching to be done inside axi_logic_analyzer core
2017-04-18 12:17:39 +02:00
610cc3affa
m2k: standalone: Disable DMA debug registers
...
The debug register logic for the DMA take up a fair amount of resources.
Disabling them frees up space in the FPGA and also helps a bit with power.
Since those registers are mainly useful in development and not so much in
production the change shouldn't have any visible external effects.
It is possible to re-enable the debug registers by setting DEBUG_BUILD=1.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-04-18 12:17:39 +02:00
c9f863f189
m2k: standalone: Set static switching activity for the reset signals
...
The global reset signals are only asserted for a short moment during system
startup and deasserted during normal operation, which is the case we care
about for power analysis. Giving them a static switching probability
indicating that they are always de-asserted will yield better results for
power analysis.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-04-18 12:17:39 +02:00
b206f8f37a
m2k: Disable AD9963 core RX datapath again
...
The RX datapath has a lot of things (IQ correction, DC filter, ...) that
take up a lot of space which are all not really needed in this project. So
disable the RX datapath.
It was previously enabled because the ad9963 core did not perform
sign-extension on the ADC data signal when the datapath was disabled. But
this has now been addressed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-04-18 12:17:39 +02:00
c1ba57f808
m2k: Rework clocking domains
...
At the moment the register map fabric and DMA system memory side are
clocked by the 100MHz sys_cpu_clk. While this works fine that is a lot
faster than the clock has to run. There are only a few 100 register map
accesses per seconds at most and they are not on timing critical paths. The
penalty from clocking them at a lower rate is negligible for the overall
system performance.
The maximum clock rate for the DMAs is determined by the throughput
requirements. This is 200 Mbytes/s for the logic analyzer, pattern
generator and each of the DAC DMAs and 400 Mbytes/s for the ADC DMA.
The DMA datapath width is 64-bit so the required clock rates are 25MHz and
50MHz respectively. Some headroom is required to accommodate for occasional
bubble cycles on the data bus and the difference in reference clocks for
the converter and processing system.
The sys_cpu_clk is reduced to 27.8MHz which is fast enough for all but the
ADC DMA. For the ADC DMA a new clock domain running at 55.6 MHz is
introduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-04-18 12:17:39 +02:00
2eaf931e07
m2k: Replace logic analyzer MMCM
...
The MMCM generating the logic analyzer clock unfortunately consumes a
disproportionately large amount of power compared to the rest of the
design.
Replace it by sourcing the logic analyzer clock from one of the Zynq FCLKs.
The IO PLL is running anyway so the power requirement is much lower.
For the time being this means we loose the ability to source the clock from
an external pin. But that feature is not supported by software at the
moment anyway. We'll bring it eventually when required.
This changes reduces power consumption by roughly 100mW.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-04-18 12:17:39 +02:00
e616c8da0b
m2k: Remove channel pack core for now
...
We always have both ADC channels enabled and the cpack core takes up a fair
amount of space, so remove it for now. Might come back later when we really
need it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-04-18 12:17:39 +02:00
efa2d0c006
m2k: Connected adc/dac resets to decimation/interpolation cores
2017-04-18 12:17:39 +02:00
500112f79b
m2k: Renamed l_clk to adc_clk and rst to adc_rst
2017-04-18 12:17:39 +02:00
6a49aefb6c
m2k: Updated project to use new tx path with serdes
2017-04-18 12:17:39 +02:00
b58a5c37eb
m2k: Reduce AXI interconnect utilization
...
Use the new axi_rd_wr_combiner module to ... the read and write DMA
interfaces into a single interface. This allows the AXI interconnect
completely optimize itself away and reduce the overall resource utilization
of the project.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-04-18 12:17:39 +02:00
71394ee465
kcu105: ip automatic version update
2017-04-18 11:59:54 +03:00
942d69a30c
Makefiles: Change MMU enabling parameter for altera designs from MMU to NIOS2_MMU
2017-04-18 10:57:16 +03:00
8e0c87e089
pluto: cleaned up some warnings
2017-04-18 10:34:13 +03:00
f3c0be0868
motcon2_fmc: cleaned up some warnings
2017-04-18 10:33:13 +03:00
6e14cdb5f4
cftl_std: cleaned up some warnings
2017-04-18 10:32:28 +03:00
d585d65692
cftl_cip: cleaned up some warnings
2017-04-18 10:29:20 +03:00
20672a3a8b
mitx045: ip automatic version update
2017-04-14 17:46:25 +03:00
954037a716
microzed: ip automatic version update
2017-04-14 17:24:24 +03:00
ebc04bcd9c
usdrx1: ip automatic version update
2017-04-14 17:16:35 +03:00
24b797f1a6
motcon2: ip automatic version update
2017-04-14 17:11:08 +03:00
4981e6e525
usb_fx3: ip automatic version update
2017-04-14 16:55:30 +03:00
c419b0042b
pluto: ip automatic version update
2017-04-14 16:55:07 +03:00
79174422b6
imageon: ip automatic version update
2017-04-14 16:54:42 +03:00
4bda0c3a1a
cftl_cip: ip automatic version update
2017-04-14 16:54:07 +03:00
afe8b071a3
cftl_std: ip automatic version update
2017-04-14 16:53:10 +03:00
1c23cf4621
all: Update verilog files to verilog-2001
2017-04-13 11:59:55 +03:00
04a4001dba
Ip automatic version update: fmcadc2, fmcadc5
2017-04-12 19:03:16 +03:00
627f78ec19
Ip automatic version update: common/board
...
- vc707
- zc702
- zed
2017-04-12 19:03:16 +03:00
6d2b3bc1c7
adi_project- try something simple first
2017-04-11 14:27:35 -04:00
1d9a8a24dc
adi_board- create_bd_cell replacement
2017-04-11 14:26:02 -04:00
bc9483c5a2
Ip automatic version: Update ad*/common/ad*_bd.tcl
...
ad6676evb/common/ad6676evb_bd.tcl
ad7616_sdz/common/ad7616_bd.tcl
ad7768evb/common/ad7768evb_bd.tcl
ad9265_fmc/common/ad9265_bd.tcl
ad9434_fmc/common/ad9434_bd.tcl
ad9467_fmc/common/ad9467_bd.tcl
ad9739a_fmc/common/ad9739a_fmc_bd.tcl
adrv9371x/common/adrv9371x_bd.tcl
adv7511/common/adv7511_bd.tcl
fmcadc4/common/fmcadc4_bd.tcl
2017-04-10 18:52:37 +03:00
454e6c0382
daq2- ad-ip-instance & ad-ip-parameter
2017-04-06 13:04:53 -04:00
2535165461
xilinx- ad-ip-instance & ad-ip-parameter
2017-04-06 13:04:19 -04:00
80f93e6a31
zc706- ad-ip-instance & ad-ip-parameter
2017-04-06 13:03:22 -04:00
820874ef93
adi_board- add auto ip version handling
2017-04-06 13:02:17 -04:00
e04793b6eb
m2k: standalone: Assign 0 to unused GPIO inputs
...
To avoid warnings from the tools assign 0 to the unused GPIO inputs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-03-30 11:16:25 +02:00
8eb1dd0a8b
adrv9371x/altera- xilinx/chip-select consistency
2017-03-29 12:59:09 -04:00
24a7d8ea9d
m2k: Remove redundant s_axi_{aclk,aresetn} assignment
...
ad_cpu_interconnect will make sure to connect the clock and the reset of
the AXI interface. Remove the redundant manual assignments.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-03-28 11:14:48 +02:00
deb8635854
adrv9371x/altera- gpio equivalency fix
2017-03-27 16:37:55 -04:00
8f1564a9c4
adrv9371x/a10gx- gpio matching
2017-03-27 13:51:45 -04:00
ae0f4672b2
daq1/a10gx- fix project to compile
2017-03-23 09:46:40 -04:00
cc6bf53d98
adrv9371x/a10soc- altera reset synchronizer false path?
2017-03-23 09:46:40 -04:00
968d94603e
fmcjesdadc1: Update xcvr configuration to the default one used for this board
2017-03-23 11:31:00 +02:00
4a275302a0
a5soc- add ddr3 location assignments
2017-03-22 10:12:34 -04:00
7e87ecae22
altera/a10gx- daq1/fmcomms2 fix typos
2017-03-22 09:48:02 -04:00
b3f06af77a
altera srf files do not work
2017-03-22 09:25:50 -04:00
66a5d44a18
a5gte- add constraints for tq
2017-03-21 10:53:31 -04:00
2e22ce3b62
a10gx- ignore preliminary timing model warnings
2017-03-21 10:52:28 -04:00
d84e34fe5f
arradio/c5soc- reset false path for vga dma
2017-03-21 10:15:38 -04:00
8063ba2b66
make updates
2017-03-20 16:05:18 -04:00
c7351f3ce3
arradio/c5soc- remove qsys files
2017-03-20 15:56:07 -04:00
589e6b53d8
arradio/c5soc- qsys-script flow
2017-03-20 15:42:33 -04:00
b39fecadd9
altera- ignore preliminary timing messages
2017-03-20 12:48:53 -04:00
7dfa8c599f
arradio/c5soc- updated to new framework/16.0
2017-03-20 12:15:18 -04:00
12f44ccbcc
arradio/c5soc- critical warnings fix
2017-03-20 12:14:21 -04:00
9b6dd27c23
ad9361- delay initialization
2017-03-15 12:06:59 -04:00
09bcecb6ed
m2k: Simplify DMA connection to HP1
2017-03-15 15:11:30 +02:00
2a9b3cea09
m2k: Changed the way DMAs connect to the PS7 DDR, to optimize resources use
2017-03-14 13:57:50 +02:00
f7c2bd943b
m2k: Enable AD9963 adc data path processing.
...
- part of the path is the sign extension module. Without it, the triggering doesn't work correctly
2017-03-13 23:18:29 +02:00
c3c8c366d3
axi_ad9361- add receive init delay
2017-03-13 16:28:53 -04:00
dac75f79ab
fmcomms5/usrpe31x- add iodelay report
2017-03-10 13:38:27 -05:00
1b3f752c3d
pzsdr1/pzsdr2/pluto- add iodelay report
2017-03-10 12:55:22 -05:00
0ae79ca7ac
move/rename - delay script belongs to ad9361
2017-03-10 12:44:32 -05:00
e736504e0f
fmcjesdadc1, usdrx1: Using the same clock in rx_data path
2017-03-10 14:26:51 +02:00
d08d1d5a1b
adrv9371x ,daq3, fmcomms7, fmcomms11: add dac_fifo missing reset connection
2017-03-10 14:20:42 +02:00
452e5e5ce0
fmcomms2- add delay reporting for iodelay
2017-03-09 15:29:15 -05:00
8bdfbe2b0a
fmcomms2- report delays
2017-03-09 15:21:42 -05:00
7e5d8664ad
fmcjesdadc1_a5gt: rx_data pins are all associated to the same clock
2017-03-09 08:57:03 +02:00
0e002f2f31
daq3_a10gx: Set XCVR Tx/RX clk/data voltage levels at 1V
2017-03-09 08:50:55 +02:00
191669ad28
daq2_common: Fix the dac_rst for DAC FIFO
2017-03-07 16:13:46 +02:00
fc8af6903f
pzsdr2/ccfmc- add rf input protection
2017-03-06 16:19:55 -05:00
3fa9a30f0e
a10soc/plddr4- lower mem clk to meet timing
2017-03-06 14:12:25 -05:00
38a27d02f6
a10soc/plddr4- differential refclk
2017-03-06 14:11:36 -05:00
936c441763
adrv9371x- dacfifo bypass-gpio control
2017-03-06 10:35:09 -05:00
762276a880
adrv9371x- dacfifo changes
2017-03-06 10:33:52 -05:00
4a6fe54fcf
daq2_common: Update common scripts
...
Add new port connection for util_dacfifo
2017-03-03 18:49:10 +02:00
ec89b1a45f
altera/adrv9371x- add dacfifo
2017-03-01 15:52:07 -05:00
bc6a09c828
adrv9371x/a10soc- dacfifo added
2017-03-01 15:35:04 -05:00
5b5c0dde99
ad6676evb: Set default xcvr parameters to common design
2017-03-01 11:32:17 +02:00
b78e9d8c27
daq2_a10gx: Set XCVR Tx/RX clk/data voltage levels at 1V
2017-03-01 11:32:17 +02:00
0cc5130c9a
adrv9371x: Set XCVR Tx/RX clk/data voltage levels at 1V
2017-03-01 11:32:17 +02:00
c1be17a3af
Altera a10 devices: disable warnings regarding unused channels
2017-03-01 11:32:17 +02:00
dc168f41fe
adrv9371_a10soc: Fixed port assignments
2017-03-01 11:32:17 +02:00
aad41039bd
a10soc- plddr4 settings
2017-02-28 13:36:28 -05:00
59dda01419
m2k: Disabled DDS cores for the generic project
2017-02-28 10:10:28 +02:00
fb4a583613
projects/system_bd- adc/dac fifo board designs
2017-02-27 16:06:39 -05:00
6b1a8852a9
dacfifo- bypass port name change
2017-02-27 16:06:39 -05:00
19c7b5d340
fmcadc5- move adc fifo settings to system-board
2017-02-27 16:06:39 -05:00
c1aac4a9fb
common: adc/dac fifo board designs
2017-02-27 16:06:39 -05:00
545e458997
m2k: Standalone, ignored critical warning for contraints that should only be applied at the implementation stage
2017-02-27 14:17:29 +02:00
eda585f0e4
m2k: Connected data[0] and trigger[0] pins to the logic analyzer clock generator input 2
2017-02-27 14:16:32 +02:00
908da60ab6
m2k: zed, changed constraints so they are the same with the ZED default configuration
...
- the voltage can be physically changed between 1.8V, 2.5V and 3.3V
2017-02-27 14:13:34 +02:00
0059c907ea
adrv9371: Drive the TX DMA interface with sys_dma_clk
2017-02-24 15:50:12 +02:00
ac2e5a9dac
constraints: Update constraints
...
Xilinx recommends that all synchronizer flip-flops have
their ASYNC_REG property set to true in order to preserve the
synchronizer cells through any logic optimization during synthesis
and implementation.
2017-02-24 13:43:32 +02:00
1fce57f6c3
axi_dacfifo: Redesign the bypass functionality
2017-02-23 17:32:31 +02:00
c598e84258
remove processing order (no clock def dependency)
2017-02-22 16:02:08 -05:00
edd5e9570f
file renamed; sed output; fingers crossed
2017-02-22 15:56:37 -05:00
b00dc4b195
plddr3- change to board files
2017-02-22 15:22:50 -05:00
89b49d2f67
fifo- as board files
2017-02-22 15:18:50 -05:00
879ed64bb6
compression flag changes
2017-02-22 15:15:53 -05:00
8a5e2ff46e
sys_wfifo- removed
2017-02-22 15:13:18 -05:00
754ac6a403
w/r-fifo- removed
2017-02-22 15:10:06 -05:00
040b61de60
fmcadc5: Updated default parameters
2017-02-20 17:13:58 +02:00
a15e05c497
adcfifo- remove axi-byte-width parameter
2017-02-17 15:29:10 -05:00
cb3d1883bc
fmcjesdadc1/a5gt- hard placement of ddr hr/qr registers
2017-02-17 15:21:33 -05:00
e8bcbb74da
scripts: fixed tcl syntax for altera projects not meeting timing
2017-02-16 21:21:51 +02:00
95a4ea20c8
axi_dacfifo: Delete redundant parameter BYPASS_EN
2017-02-16 19:53:44 +02:00
8453d758c2
scripts: If an altera project doesn't meet timing, rename the sof
2017-02-16 19:20:49 +02:00
343d0472d4
fmcadc2: Move GT setting to common/system_bd.tcl
2017-02-16 14:56:25 +02:00
07184b31d2
fmcadc2: Define default clock selection for Xilinx GTs
2017-02-16 12:35:24 +02:00
86c279c238
pzsdr1: ccbox, moved I2S core to DMA0 and DMA1 to fix critical warnings
2017-02-14 14:51:49 +02:00
46290193f3
pzsdr2: ccusb, renamed clk_out to clkout_in
2017-02-14 11:58:11 +02:00
27119343f2
pzsdr2: ccusb, connect unused clock pins to GND
2017-02-14 11:56:54 +02:00
fa37f4dd0a
pzsdr2: Don't set a disabled parameter
2017-02-14 11:56:08 +02:00
6a9b7580de
pzsdr1: ccusb, renamed clk_out to clkout_in
2017-02-14 11:54:46 +02:00
acef0113d1
pzsdr1: ccusb, connect unused clock pins to GND
2017-02-14 11:50:37 +02:00
46883731eb
pzsdr1: Don't set a disabled parameter
2017-02-14 11:50:06 +02:00
a569b6bf0c
pluto: Interpolation, connect fifo_rd_valid to s_axis_data_tvalid
2017-02-13 18:08:52 +02:00
e215a091b2
m2k: standalone, added explicit fclk_clk0 and fclk_clk1 constraints
2017-02-13 12:02:59 +02:00
4e62fb0ef3
m2k: Add reset circuitry on the logic_analyzer clock domain
2017-02-13 12:02:11 +02:00
5fa6dba333
Make: Update Makefiles
2017-02-10 16:32:58 +02:00
f5f1f47691
ad9467_fmc: Delete asynchronous clock group definition
...
This is a very bad way to handle timing. All the false path
should be defined explicitly, rather than define asynchronous clock
domains.
2017-02-10 16:21:35 +02:00
c39ed08edd
zcu102/*- actual clock == desired clock
2017-02-06 12:53:47 -05:00
58872aa3ef
fmcomms2/zc706pr- prcfg is a single clock synchronous design
2017-02-06 10:59:18 -05:00
971bcbb0fc
fmcomms1: Remove project
2017-02-03 16:42:44 +02:00
096274a033
daq2/zcu102- fix refclock pin swap
2017-02-03 09:26:07 -05:00
7c363cd5a7
daq3/a10gx/system_constr.sdc- fix typo
2017-02-03 09:26:07 -05:00
35f660fe06
fmcjesdadc1/vc707- constraint clean-up
2017-02-02 15:05:49 -05:00
d46352928a
fmcomms5- fix ovf net connections
2017-02-02 14:24:06 -05:00
6aadb49e80
m2k: Remove use board flow from the standalone version
2017-02-02 12:58:58 +02:00
0d0c3e99fd
m2k: Added I2C pull-ul, removed SLEW constraints
2017-02-02 12:35:46 +02:00
85ff496c12
daq2/a10gx- gpio match with others
2017-02-01 20:54:56 -05:00
5155b3f46d
m2k: Fix gpio buswidth
2017-02-01 17:43:01 +02:00
cfff70d358
M2K: Update standalone project
...
- configured PS7 similar to pluto. Added specific constraints instead of default PS7
- moved ad9963_resetn and en_power_analog to gpio[0] and gpio[1]
2017-02-01 14:27:11 +02:00
6bdd853b88
m2k: Updated PS7 configuration
2017-01-31 23:08:53 +02:00
b14d740f87
M2K: initial commit
2017-01-31 16:43:40 +02:00
d5af828b9c
Merge branch 'dev' into hdl_2016_r2
2017-01-30 17:10:05 +02:00
97d72d2f65
a10gx- xilinx/altera sync-up
2017-01-30 10:01:28 -05:00
b14e7fe4ee
daq3/kcu105- 1.25GSPS
2017-01-30 10:01:28 -05:00
48ad24cdbe
enable partial reconfiguration mode
2017-01-27 09:26:53 -05:00
be1328c55b
kcu105- added missing ethernet configurations
2017-01-23 10:14:09 -05:00
661413627f
daq3- round about way to avoid ip getting locked
2017-01-20 15:55:33 -05:00
62792ddaed
adrv9371x: Change the axi_adxcvr cores addresses
...
Because the S_AXI interface of the axi_adxcvr core was infered
using the process adi_ip_properties, the interface address range
has changed from 4k to 64k. As a result, all the addresses of
the axi_adxcvr cores were changed and realigned.
2017-01-19 15:23:03 +02:00
ecd152c90d
pzsdr1: ccbrk_cmos, fix clkdiv parameters
2017-01-18 12:04:04 +02:00
165ba76d9d
pzsdr1: Added FIFOs for DAC and ADC paths so that they work at l_clk or l_clk/2
2017-01-18 12:01:24 +02:00
319a883c00
pzsdr2: Added FIFOs for DAC and ADC paths so that they work at l_clk/2 or l_clk/4
2017-01-18 12:00:10 +02:00
9344dd34dc
zcu102: Update project to include clkdiv
2017-01-16 14:47:31 +02:00
4dcad7e116
fmcomms2: zcu102, update clkdiv device parameter
2017-01-16 14:38:37 +02:00
b622b6592e
FMCOMMS5/ZCU102 : Merge from njpillitteri/hdl:dev
...
Pull request Dev #26
2017-01-13 14:47:16 +02:00
d2e7b6b635
fmcomms5: Added FIFOs for DAC and ADC paths so that they work at l_clk/2 or l_clk/4
2017-01-13 14:18:59 +02:00
a36057679a
fmcomms2: Update Makefiles
2017-01-13 14:16:21 +02:00
15c5bc7012
fmcomms2: zcu102, changed clkdiv C_SIM_DEVICE parameter to ultrascale
2017-01-13 13:57:32 +02:00
b84325d43f
fmcomms2: take into consideration both adc_r1 and dac_r1 for clock division selection
2017-01-13 13:56:04 +02:00
f003b5b35a
fmcjesdadc1: Reduce SYSREF period
2017-01-12 16:10:45 +02:00
e77428c50e
fmcomms2: Added FIFOs for DAC and ADC paths so that the path works at l_clk / 2 or l_clk /4
...
- removed ILA
2017-01-11 18:12:35 +02:00
37d54bb984
fmcjesdadc1/a5gt- max delay fit only
2017-01-04 16:04:19 -05:00
8b74e911b8
fmcjesdadc1/a5gt- qr to ddio max delay
2017-01-04 14:10:44 -05:00
e4e5b30ade
fmcadc5: Integrate ad_sysref_gen into the project
2017-01-03 13:52:39 +02:00
14ded4f123
fmcjeadadc1/a5soc- ad_sysref_gen updates
2016-12-22 15:59:45 -05:00
b089173b4c
fmcjesdadc1/a5soc- cpu clock is 50m for a5gt also
2016-12-22 14:14:21 -05:00
aa6c94c993
usdrx1/a5gt: ddr3 use ip constraints
2016-12-22 14:14:21 -05:00
18660c7ab4
fmcjesdadc1/a5gt: ddr3 use ip constraints
2016-12-22 14:14:21 -05:00
2bea337aa2
fmcjesdadc1/a5gt- use 50m-mem-cpu-clk
2016-12-22 14:14:21 -05:00
5d683943ab
fmcjesdadc1/a5gt- remove ad-sysref-gen-pack
2016-12-22 14:14:21 -05:00
f1168f9e29
fmcjesdadc1/a5gt- use xilinx setup 2-dma
2016-12-22 14:14:21 -05:00
1ceec2e2a9
projects/a5gt- use 50m afi clock for cpu- xcvr reconfig timing
2016-12-22 14:14:21 -05:00
eba30b0cde
projects/altera- qii_auto_pack option
2016-12-22 14:14:21 -05:00
4a783d523d
projects/altera* - default & common qsys commands
2016-12-20 16:27:44 -05:00
3e57ff1fc5
z-mpsoc- map 0x4-0x8,0x7-0x9
2016-12-20 16:14:38 -05:00
1156aeac16
ad_sysref_gen: Update SYSREF related constraints
2016-12-19 18:07:05 +02:00
da7f4608a8
fmcjesdadc1/usdrx1: Clean up the mess
...
Delete accidentally commited generated files.
2016-12-19 15:35:20 +00:00
f47863bbcf
usdrx1: Integrate ad_syref_gen into the project
2016-12-19 14:36:01 +00:00
8d799d0316
fmcjesdadc1: Intergrate ad_sysref_gen into project
2016-12-19 13:37:29 +00:00
0c42e04bc3
fmcadc2: Integrate ad_sysref_gen into the project
2016-12-19 12:16:05 +00:00
67390c2a95
ad6676evb: Update projects with ad_sysref_gen
2016-12-19 10:52:25 +00:00
8879218502
a5gte: Fixed timing violations
2016-12-16 15:37:51 +02:00
c0b0f9b7e9
ad6676evb: Connect SYS_REF to GPIO
2016-12-14 17:55:50 +02:00
557efed5d9
ad6676evb: Update clock constraints
2016-12-14 17:55:49 +02:00
3a2c889115
ad6676evb: Update GT configuration
2016-12-14 17:55:49 +02:00
d962614000
usdrx1/zc706: Disabele axi_spi constraint file
...
The interface ports of the AXI SPI IP are not connected
directly to a IOBUF, this results in a CRITICAL WARNING
2016-12-13 19:23:51 +02:00
d5165ca81f
motcon_fmc: Tie unused pins to GND
2016-12-13 19:20:13 +02:00
1515b6f1af
fmcomms7/zc706: Disabele axi_spi constraint file
...
The interface ports of the AXI SPI IP are not connected
directly to a IOBUF, this results in a CRITICAL WARNING
2016-12-13 19:18:18 +02:00
8846141467
fmcomms1/kc705: Disabele axi_spi constraint file
...
The interface ports of the AXI SPI IP are not connected
directly to a IOBUF, this results in a CRITICAL WARNING
2016-12-13 19:16:31 +02:00
c455d2d64f
fmcadc2/vc707: Disabele axi_spi constraint file
...
The interface ports of the AXI SPI IP are not connected
directly to a IOBUF, this results in a CRITICAL WARNING
2016-12-13 19:15:44 +02:00
8ebc8fe4e2
updated makefiles
2016-12-09 23:06:41 +02:00
06aab8ebbd
pzsdr1: Set the device core to 1R1T mode
2016-12-09 16:35:46 +02:00
8e69c838e1
common/ac701: Connect axi_ddr_cntrl/device_temp_i to GND
2016-12-09 13:54:39 +02:00
23c91ca48a
pzsdr1/lvds: The interface runs at max 122.88 MHz
2016-12-09 11:45:11 +02:00
f799c40cf0
usdrx1/a5gt- xcvr interface changes
2016-12-08 16:05:23 -05:00
c114888956
usdrx1- updates
2016-12-08 16:05:23 -05:00
b0eff57b0f
fmcomms2/zc702: Fix critical warnings
2016-12-08 19:54:52 +02:00
3dceb53984
fmcadc2/vc707: Fix timing violations
2016-12-08 19:51:18 +02:00
252c67ceff
fmcomms6: Delete project
...
This project will not be supported in further releases.
2016-12-08 17:22:41 +02:00
fb287d0178
kcu105- updates to match xilinx trd
2016-12-08 09:32:33 -05:00
3bc9df4c51
fmcomms5: Fixed the wornings created by TDD missing connections to axi_ad9361 core
2016-12-07 21:43:19 +02:00
8eaae98728
fmcadc2: Updates
2016-12-07 21:43:19 +02:00
801da3cb25
daq3/kcu105- fix timing violations
2016-12-06 12:31:40 -05:00
2d7fb03b93
adrv9371x/a10gx- fix os xcvr parameters
2016-12-06 12:31:40 -05:00
ad96c5e881
daq3/zc706: Change the speed grade of the FPGA to 3
2016-12-06 15:24:23 +02:00
8f94103f8b
daq1/a10gx: Makefile fix
2016-12-06 15:24:23 +02:00
95ee7c093c
daq1/a10gx: Update system_bd port names
2016-12-06 15:24:23 +02:00
b7143a7a3b
daq1/a10gx: Update IO pin assignments
2016-12-06 15:24:22 +02:00
a415625069
daq1/a10gx: Add spi wrapper file to the project
2016-12-06 15:24:22 +02:00
e30a80fda0
daq1_spi: Delete device specific macro instantiation
2016-12-06 15:24:21 +02:00
7a8dc92b84
usb_fx3: Add interrupt monitor and increase ILA data depth
2016-12-06 11:55:28 +02:00
1e4bdea80c
usrpe31x: Fix Makefile
2016-12-06 11:07:42 +02:00
4b7bf422ee
pzsdr2/ccbox- remove imu intr on pl
2016-12-05 10:21:42 -05:00
351811e13f
pzsdrx/ccbox- imu intr on gpio
2016-12-05 10:18:40 -05:00
170c781d02
hdlmake.pl- updates
2016-12-01 13:52:11 -05:00
6e89ac3d65
pzsdr2: ccusb_lvds, add flag_a,flag_b signals
2016-11-30 17:39:02 +02:00
0faa1ebff2
pzsdr1: ccusb_lvds, add flag_a,flag_b signals
2016-11-30 17:38:04 +02:00
84a76b9dea
imageon: Invert HDMI TX clock
...
The ADV7511 samples the parallel data bus at the rising edge of sample
clock. Generate the clock so that the falling edge is aligned to updating
the bus data. This creates larger timing margins on each side of the
sampling edge and makes the design more robust.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-11-29 15:43:24 +01:00
24cc8d284b
imageon: Increase RX DMA FIFO size
...
Increase the RX DMA FIFO to be able to better compensate for momentarily
memory bus contention. This has shown to resolve occasional overflows that
would occur under high system memory load.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-11-29 14:12:39 +01:00
99dae73d96
imageon: Connect hdmi_rx_core output clock to DMA
...
Connect the HDMI RX core output clock to the DMA rather than connecting the
HDMI RX input clock directly. This will allow the HDMI RX core to modify
the clock and e.g. insert clock buffers or similar.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-11-29 14:12:39 +01:00
07217740b5
imageon: Increase HDMI RX clock constraint
...
The ADV7611 is rated for a maximum clock rate of 165MHz. Increase the clock rate constraint to match this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-11-29 14:12:39 +01:00
284fbac571
usdrx1: Xcvr updates, so that the channel parameters are correctly configured from boot time
2016-11-28 14:16:07 +02:00
45fd4f806d
fmcjesdadc1: Fixed RX_PMA_CFG parameter
2016-11-25 16:33:58 +02:00
11b57290f1
fmcadc5- replaced with axi_adxcvr
2016-11-23 16:22:05 -05:00
22e230618c
scripts/adi_board.tcl- support multiple xcvrs
2016-11-23 16:22:05 -05:00
862bd7ef2c
daq3/zc706- xcvr changes
2016-11-23 15:02:20 -05:00
4e3e623530
pzsdr2/ccpci- updates
2016-11-23 14:02:59 -05:00
e5d3bae54d
projects/ad6676-adrv9371: xcvr updates
2016-11-23 11:06:22 -05:00
daa3df4b96
projects/- xcvr updates
2016-11-22 16:23:05 -05:00
8f562fd069
xcvr updates- board procedure
2016-11-22 14:43:36 -05:00
b1a9bd96f1
daq2: xcvr pll changes
2016-11-22 12:53:29 -05:00
750b23621b
board-tcl: xcvr qpll/cpll changes
2016-11-22 12:53:02 -05:00
4ed7469286
fmcadc4/zc706- updates
2016-11-22 10:32:05 -05:00
8c4279f618
pzsdr1: Added ccusb_lvds initial project
2016-11-22 16:58:34 +02:00
3d0049d274
pzsdr2: ccusb_lvdsr, updated project for the latest schematic
2016-11-22 16:55:52 +02:00
aff45eae5f
fmcadc2: xcvr updates
2016-11-21 18:45:38 +02:00
69ee410d3d
fmcomms2/zc706pr- bypass pr as default
2016-11-21 09:45:10 -05:00
4739d05269
zc706pr/common- removed
2016-11-18 14:52:39 -05:00
f43248c2bc
common/pzsdr*- removed
2016-11-18 11:32:43 -05:00
0d75bcb606
pzsdr2: ccbox: Use DMA interface 0+1 for audio
...
There is a bug in the ps7 component specification that causes critical
warnings to appear in the build log if DMA interface 0 is disabled, but any
other DMA interface is enabled.
Work around this issue by using DMA interface 0 and 1 instead of 1 and 2
for the I2S DMA.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-11-18 14:03:46 +01:00
b62f60b0da
pzsdr1/ccbox- updates
2016-11-17 16:14:28 -05:00
935f8a5c7b
pzsdr1/ccbox- constraints
2016-11-17 16:13:53 -05:00
4f65bcb3b2
pzsdr1/ccbrk_cmos- updates
2016-11-17 15:32:49 -05:00
e85dd2740a
pzsdr1/ccbrk_lvds- updates
2016-11-17 15:32:25 -05:00
a61da1d2ac
pzsdr1/common- updates
2016-11-17 15:31:25 -05:00
aa02ca875f
pzsdr1- common files
2016-11-17 13:40:25 -05:00
8c25402d53
pzsdr1- common files
2016-11-17 13:40:04 -05:00
4dae754287
pzsdr1- added readme
2016-11-17 11:29:01 -05:00
778638a7a1
pzsdr2- make updates
2016-11-17 10:26:45 -05:00
74bf4dfb80
pzsdr2- gpio- turn-around
2016-11-17 10:24:50 -05:00
d0166a4c7e
ccbox- updates
2016-11-17 10:24:11 -05:00
c2b7cbd61b
ccbox- constraints
2016-11-17 10:23:51 -05:00
5e6b931150
ccbox- added
2016-11-17 09:28:33 -05:00
Adrian Costina
Lars-Peter Clausen
Istvan Csomortani
AndreiGrozav
Rejeesh Kutty
Nick Pillitteri