2e1e0939ce
fmcomms2- dma parameters & ila cores upgrade
2015-08-26 14:12:57 -04:00
9e5e7d6805
remove rfsom from fmcomms2
2015-08-20 10:33:43 -04:00
d52308f074
axi_dmac: Change parameter name 2D_TRANSFER
...
Parameter name can't start with numbers, 2D_TRANSFER was changed to DMA_2D_TRANSFER
2015-08-20 10:14:22 +03:00
57cfb7cfb1
hdl/library: Update the IP parameters
...
The following IP parameters were renamed:
PCORE_ID --> ID
PCORE_DEVTYPE --> DEVICE_TYPE
PCORE_IODELAY_GROUP --> IO_DELAY_GROUP
CH_DW --> CHANNEL_DATA_WIDTH
CH_CNT --> NUM_OF_CHANNELS
PCORE_BUFTYPE --> DEVICE_TYPE
PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE
CHID --> CHANNEL_ID
PCORE_DEVICE_TYPE --> DEVICE_TYPE
PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N
PCORE_SERDES_DDR_N --> SERDES_DDR_N
PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE
DP_DISABLE --> DATAPATH_DISABLE
PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE
C_BIG_ENDIAN --> BIG_ENDIAN
C_M_DATA_WIDTH --> MASTER_DATA_WIDTH
C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH
NUM_CHANNELS --> NUM_OF_CHANNELS
CHANNELS --> NUM_OF_CHANNELS
PCORE_4L_2L_N -->QUAD_OR_DUAL_N
C_ADDRESS_WIDTH --> ADDRESS_WIDTH
C_DATA_WIDTH --> DATA_WIDTH
C_CLKS_ASYNC --> CLKS_ASYNC
PCORE_QUAD_DUAL_N --> QUAD_DUAL_N
NUM_CS --> NUM_OF_CS
PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID
PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID
PCORE_CLK0_DIV --> CLK0_DIV
PCORE_CLK1_DIV --> CLK1_DIV
PCORE_CLKIN_PERIOD --> CLKIN_PERIOD
PCORE_VCO_DIV --> VCO_DIV
PCORE_Cr_Cb_N --> CR_CB_N
PCORE_VCO_MUL --> VCO_MUL
PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC
PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH
PCORE_ADDR_WIDTH --> ADDRESS_WIDTH
DADATA_WIDTH --> DATA_WIDTH
NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS
DEBOUNCER_LEN --> DEBOUNCER_LENGTH
ADDR_WIDTH --> ADDRESS_WIDTH
C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED
Cr_Cb_N --> CR_CB_N
ADDATA_WIDTH --> ADC_DATA_WIDTH
BUFTYPE --> DEVICE_TYPE
NUM_BITS --> NUM_OF_BITS
WIDTH_A --> A_DATA_WIDTH
WIDTH_B --> B_DATA_WIDTH
CH_OCNT --> NUM_OF_CHANNELS_O
M_CNT --> NUM_OF_CHANNELS_M
P_CNT --> NUM_OF_CHANNELS_P
CH_ICNT --> NUM_OF_CHANNELS_I
CH_MCNT --> NUM_OF_CHANNELS_M
4L_2L_N --> QUAD_OR_DUAL_N
SPI_CLK_ASYNC --> ASYNC_SPI_CLK
MMCM_BUFIO_N --> MMCM_OR_BUFIO_N
SERDES_DDR_N --> SERDES_OR_DDR_N
CLK_ASYNC --> ASYNC_CLK
CLKS_ASYNC --> ASYNC_CLK
SERDES --> SERDES_OR_DDR_N
GTH_GTX_N --> GTH_OR_GTX_N
IF_TYPE --> DDR_OR_SDR_N
PARALLEL_WIDTH --> DATA_WIDTH
ADD_SUB --> ADD_OR_SUB_N
A_WIDTH --> A_DATA_WIDTH
CONST_VALUE --> B_DATA_VALUE
IO_BASEADDR --> BASE_ADDRESS
IO_WIDTH --> DATA_WIDTH
QUAD_DUAL_N --> QUAD_OR_DUAL_N
AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT
ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH
ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH
MODE_OF_ENABLE --> CONTROL_TYPE
CONTROL_TYPE --> LEVEL_OR_PULSE_N
IQSEL --> Q_OR_I_N
MMCM --> MMCM_OR_BUFR_N
2015-08-19 14:11:47 +03:00
10d9de39a1
axi_ad9361/tdd: Update the synchronization logic
...
The master will regenerate a sync pulse periodically. The period can be defined by software.
2015-08-19 12:21:23 +03:00
bcee3e04d4
fmcomms2_tdd: Update tdd_enabaled path
...
This line controls the mux, which switch between hdl and software (GPIO) control of the ENABLE/TXNRX pins.
Fix the broken path and change the name from "tdd_enable" to "tdd_enabled".
2015-08-19 12:14:05 +03:00
d2c99acae8
fmcomms2/TDD: Update synchronization interface
...
Synchronization is done by a simple req/ack interface between a master and slave terminal.
2015-08-06 15:14:36 +03:00
8e631e56d6
fmcomms2: Add a synchronization interface for TDD mode.
...
Supported carrier are ZC706 and RFSOM.
The synchronization pulse is automatically generated by the master terminal, when TDD mode is enabled.
By default a terminal is slave, software must write 0x01 into TDD register 0x50.
2015-07-28 14:42:54 +03:00
28aea82952
fmcomms2_zc702: Add SPI and GPIO interface for FREQCVT
2015-07-22 10:16:04 +03:00
a7da779b94
Makefile: Updated Makefiles
2015-07-16 18:19:42 +03:00
1dcbf5e5a2
fmcomms2/zc706: Fix GPIO connections
...
Fix GPIO connections for the FREQCVT board.
2015-07-15 15:12:01 +03:00
a38339a3ec
fmcomms2/rfsom: Add GPIO control for the RF card
2015-07-14 13:12:54 +03:00
ba2029a6e8
fmcomms2/rfsom: Delete trailing whitespaces from system_constr.xdc
2015-07-14 13:12:53 +03:00
46fa91d5be
Makefile: Update Make files
2015-07-03 18:08:57 +03:00
95500d4022
fmcomms2_rfsom: Fix GPIO connections
2015-07-03 13:03:19 +03:00
0102e3e02c
fmcomms2_ALL: Preserve backward compatibility for ENABLE/TXNRX control
...
By default the ENABLE/TXNRX pins are controlled by GPIOs, if the TDD module is enabled, the TDD FSM will take over the control of these two pins.
2015-07-01 13:54:01 +03:00
6862655b0d
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-06-26 11:07:10 +02:00
25e56a4d03
arradio: renamed fmcomms2 c5soc to arradio
2015-06-08 11:35:21 +03:00
dc7064ab95
fmcomms2/vc707 - wfifo changes
2015-06-05 12:44:04 -04:00
25f1ad73f0
fmcomms2/freqcvt: Update SPI interface I/O
2015-06-05 18:16:14 +03:00
f1e75963a2
fmcomms2: wfifo+pack changes
2015-06-05 09:20:50 -04:00
3b1ea7e528
axi_ad9361/tdd: Cherry picked commit 598ece4 from hdl_2015_r1 branch
...
598ece4c8d
2015-06-04 18:09:47 +03:00
f81d22a17a
altera- common timing check
2015-06-04 10:56:32 -04:00
a6cae6b477
iobuf: do is a system verilog keyword
2015-05-21 14:06:17 -04:00
6b9906b22b
Refresh Makefiles
...
Re-generate the Makefiles after a small update to the generation script:
- Entries are sorted alphabetically
- Empty dependency lines are skipped
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-05-21 14:21:54 +02:00
0805da3b6b
fmcomms2/rfsom- enable dac delay
2015-05-18 16:45:54 -04:00
3e51d29f75
enable/txnrx- tdd changes
2015-05-18 14:28:20 -04:00
c19749361d
Makefiles: Updated makefiles to have as a result the programming file instead of the project file.
...
Also fixed altera projects dependencies
2015-05-18 17:22:46 +03:00
d9a124b767
fmcomms2_zc706: TDD integration, initial commit.
2015-05-11 12:20:45 +03:00
293ec6a319
fmcomms2: c5soc project updated to 14.1
2015-05-08 17:44:16 +03:00
91279253ef
Makefiles: Added mig project file as a dependency for Microblaze based projects. Also updated usdrx1 a5gt Makefile
2015-05-08 15:31:40 +03:00
949abcdc8f
Makefile: Updated makefiles so that the project recipe does not depend on lib
2015-05-06 14:58:29 +03:00
319f821fab
zc706pr - makefile
2015-05-04 13:41:03 -04:00
ab85e2ba36
zc706pr - 706 partial reconfiguration
2015-05-04 12:36:57 -04:00
c3dd9258e7
zc706: project mode
2015-05-04 10:25:12 -04:00
62acd37fee
zc706: project mode
2015-05-04 10:25:07 -04:00
ad551a0073
itx045: updates
2015-05-01 16:18:43 -04:00
00cafd4df0
fmcomms2/zc706: add partial reconfiguration
2015-05-01 12:23:18 -04:00
3641d8f714
fmcomms2/zc706: add partial reconfiguration
2015-05-01 12:23:11 -04:00
75a81d67d8
fmcomms2/zc706: add partial reconfiguration
2015-05-01 12:23:07 -04:00
140c622c8b
prcfg: common files
2015-05-01 11:48:09 -04:00
a8d4c916c1
fmcomms2_bd: remove axi3 switch
2015-05-01 11:47:29 -04:00
3fd830b038
fmcomms2: Use AXI3 interface for the DMA on ZYNQ
...
On ZYNQ the HP interconnects have a AXI3 interface. The DMA controller
supports both AXI4 and AXI3. By switching to AXI3 there is no need to create
a protocol converter between the DMA and the HP port.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-17 19:51:37 +02:00
71d4f3a474
fmcomms2: Don't mark synchronous paths as asynchronous for the DMAs
...
The AXI master interface and the register map AXI slave interface use the
same clock. No need to mark the interfaces as asynchronous. This removes the
need for CDC logic on those paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-17 19:51:37 +02:00
dc2b37bd0c
Makefile: Added top level Makefile. Modified behavior of clean and clean-all
...
Clean ran for a project will clean only the project files.
Clean-all ran for a project will clean also the library files on which the project depends.
The clean commands will only remove specific files and directories.
The top Makefile allows several options(per suggestion from jameyhicks):
make fmcomms1.zed will run "make all" in projects/fmcomms1/zed/
make clean will run "make clean" for all the projects
make clean-all will run "make clean" for all the projects and libraries
make lib will run "make all" for the library files
2015-04-17 17:22:38 +03:00
374f82e7de
makefiles: The clean command for library won't remove the xml files, except for component.xml.
...
Updated also the dmac dependencies
2015-04-16 11:53:27 +03:00
780455d68c
Makefile: Updated makefiles. Added makefiles for altera
2015-04-09 17:57:06 +03:00
5f8e9a74ea
makefile: updated
2015-04-07 16:32:01 -04:00
f79a152958
Makefiles: updated all makefiles adding clean functionality
2015-04-03 11:57:54 +03:00
9745462d88
fmcomms2: VC707 fixed top file
2015-04-02 15:31:40 +03:00
Rejeesh Kutty
Istvan Csomortani
Adrian Costina
Lars-Peter Clausen