- Removes the reset_tx_pll_and_datapath_in reset
- Connects gtreset_in to make use of the master reset found inside
the Transceiver Bridge IP
- Connects the necessary signals for the master reset between the
Transceiver Wizard and Transceiver Bridge
ad9209/vck190/system_top: Connect versal transceiver reset
Signed-off-by: Bogdan Luncan <bogdan.luncan@analog.com>
The following CWs appeared (even in Vivado version 2021.2):
* CRITICAL WARNING: [BD 41-1356] Slave segment </sys_ps7/S_AXI_HP1/HP1_DDR_LOWOCM> is not assigned into address space </axi_rd_wr_combiner_logic/m_axi>. Please use Address Editor to either assign or exclude it.
* CRITICAL WARNING: [BD 41-1356] Slave segment </sys_ps7/S_AXI_HP2/HP2_DDR_LOWOCM> is not assigned into address space </axi_rd_wr_combiner_converter/m_axi>. Please use Address Editor to either assign or exclude it.
Signed-off-by: Iulia Moldovan <Iulia.Moldovan@analog.com>
Add a list with make commands with the proper parameters for each devicetree
availible at the moment.
Signed-off-by: LIacob106 <liviu.iacob@analog.com>
The ADI_EXTRACT_PORTS variable is used to extract all the ports and nets properties of the desired IPS for the TransceiverToolbox and HighSpeedConverterToolbox to be later used for generating the json files automatically.
The ADI_SKIP_SYNTHESIS variable is used to stop the building process before the synthesis when used with Matlab support as it is not necessary at this point.
The ADI_MATLAB variable is used to choose the correct paths when building the design when using the HWA workflow.
The SPI Engine cores were named directly inside the script and this
would mean that for multiple SPI Engine instances IPs with the same
name would appear. These updates will introduce the hierarchy name
into the name given to the cores and will therefore allow for
multiple instances of SPI Engine to be added to the same Xilinx
project.
Projects which use spi_engine.tcl will be updated to account for
these changes.
- Quartus version was updated
- the start_n output port was deteled from system_top.v
- the ""mixed_port_feed_through_mode" parameter of RAM can not have value "old"" warning was disabled
- update Makefile copyright year
Signed-off-by: Paul Pop <paul.pop@analog.com>
bug:
say "make LVDS_CMOS_N=0"
- will set ad_project_dir as LVDSCMOSN0
- will then set system_qip_file as LVDSCMOSN0/system_bd/synthesis/system_bd.qip
- build error reveals system_bd can't be found
- maybe due to setting ad_project_dir as a relative file path
fix:
- set ad_project_dir as an absolute file path
Signed-off-by: Jem Geronimo <Johnerasmusmari.Geronimo@analog.com>
Running 'make' will build the default project directly in the project folder (like it did before)
Running 'make RX_LANE_RATE=15 TX_LANE_RATE=15' will build the project inside the 'RXRATE15_TXRATE15' subdirectory.
Running 'make CFG=cfg/test_config.txt" will use the variables found inside the configuration file and build the project inside the 'test_config' subdirectory.
Running 'make clean' will clean the default project only.
Running 'make CFG=cfg/test_config.txt clean' will clean the 'testconfig' build.
Running 'make clean-all' will delete all the built configurations and libraries.
Note that the 'JESD' and 'LANE' words from the parameter names are stripped.
Signed-off-by: Bogdan Luncan <bogdan.luncan@analog.com>
In ad_xcvrcon procedure from adi_board, phy_en_char_align must be connected only when 8B10B encoding is used,
otherwise this signal does not exists in the JESD ip and will cause an error.
Signed-off-by: Filip Gherman <Filip.Gherman@analog.com>
Bogdan Luncan
alin724
Iulia Moldovan
LIacob106
Filip Gherman
PIoandan
Stanca Pop
ladace
sergiu arpadi
laurent-19
Paul Pop
Jem Geronimo
Istvan-Zsolt Szekely
AndrDragomir
Ionut Podgoreanu