57cfb7cfb1
hdl/library: Update the IP parameters
...
The following IP parameters were renamed:
PCORE_ID --> ID
PCORE_DEVTYPE --> DEVICE_TYPE
PCORE_IODELAY_GROUP --> IO_DELAY_GROUP
CH_DW --> CHANNEL_DATA_WIDTH
CH_CNT --> NUM_OF_CHANNELS
PCORE_BUFTYPE --> DEVICE_TYPE
PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE
CHID --> CHANNEL_ID
PCORE_DEVICE_TYPE --> DEVICE_TYPE
PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N
PCORE_SERDES_DDR_N --> SERDES_DDR_N
PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE
DP_DISABLE --> DATAPATH_DISABLE
PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE
C_BIG_ENDIAN --> BIG_ENDIAN
C_M_DATA_WIDTH --> MASTER_DATA_WIDTH
C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH
NUM_CHANNELS --> NUM_OF_CHANNELS
CHANNELS --> NUM_OF_CHANNELS
PCORE_4L_2L_N -->QUAD_OR_DUAL_N
C_ADDRESS_WIDTH --> ADDRESS_WIDTH
C_DATA_WIDTH --> DATA_WIDTH
C_CLKS_ASYNC --> CLKS_ASYNC
PCORE_QUAD_DUAL_N --> QUAD_DUAL_N
NUM_CS --> NUM_OF_CS
PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID
PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID
PCORE_CLK0_DIV --> CLK0_DIV
PCORE_CLK1_DIV --> CLK1_DIV
PCORE_CLKIN_PERIOD --> CLKIN_PERIOD
PCORE_VCO_DIV --> VCO_DIV
PCORE_Cr_Cb_N --> CR_CB_N
PCORE_VCO_MUL --> VCO_MUL
PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC
PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH
PCORE_ADDR_WIDTH --> ADDRESS_WIDTH
DADATA_WIDTH --> DATA_WIDTH
NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS
DEBOUNCER_LEN --> DEBOUNCER_LENGTH
ADDR_WIDTH --> ADDRESS_WIDTH
C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED
Cr_Cb_N --> CR_CB_N
ADDATA_WIDTH --> ADC_DATA_WIDTH
BUFTYPE --> DEVICE_TYPE
NUM_BITS --> NUM_OF_BITS
WIDTH_A --> A_DATA_WIDTH
WIDTH_B --> B_DATA_WIDTH
CH_OCNT --> NUM_OF_CHANNELS_O
M_CNT --> NUM_OF_CHANNELS_M
P_CNT --> NUM_OF_CHANNELS_P
CH_ICNT --> NUM_OF_CHANNELS_I
CH_MCNT --> NUM_OF_CHANNELS_M
4L_2L_N --> QUAD_OR_DUAL_N
SPI_CLK_ASYNC --> ASYNC_SPI_CLK
MMCM_BUFIO_N --> MMCM_OR_BUFIO_N
SERDES_DDR_N --> SERDES_OR_DDR_N
CLK_ASYNC --> ASYNC_CLK
CLKS_ASYNC --> ASYNC_CLK
SERDES --> SERDES_OR_DDR_N
GTH_GTX_N --> GTH_OR_GTX_N
IF_TYPE --> DDR_OR_SDR_N
PARALLEL_WIDTH --> DATA_WIDTH
ADD_SUB --> ADD_OR_SUB_N
A_WIDTH --> A_DATA_WIDTH
CONST_VALUE --> B_DATA_VALUE
IO_BASEADDR --> BASE_ADDRESS
IO_WIDTH --> DATA_WIDTH
QUAD_DUAL_N --> QUAD_OR_DUAL_N
AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT
ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH
ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH
MODE_OF_ENABLE --> CONTROL_TYPE
CONTROL_TYPE --> LEVEL_OR_PULSE_N
IQSEL --> Q_OR_I_N
MMCM --> MMCM_OR_BUFR_N
2015-08-19 14:11:47 +03:00
6862655b0d
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-06-26 11:07:10 +02:00
71b5004b25
projects- drp moved to up-clock domain
2015-06-01 14:57:59 -04:00
f232a36141
common: Place HDMI interface registers into the IOB
...
The paths from the HDMI interface registers to the IO pads are
unconstrained. This means the P&R can in theory put the register anywhere
which could lead to stability issues on the interface, depending on what
else is in the fabric. To get predictable delays for the register to IO pad
path place the register into the IOB section.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-23 14:33:47 +02:00
ab5c7bb57b
common: zc702: Use interface connection for the HDMI DMA stream
...
Use a interface connection for the HDMI DMA stream instead of individually
connecting each of the signals. This make things a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-04-08 13:29:25 +02:00
ea303c6f61
zc702: Updated base design to the latest model
2015-03-13 12:44:08 +02:00
05ed98f884
common: Updated common constratins for ac701, kc705, vc707, zc702
2014-11-11 12:35:44 +02:00
ba53e156e3
ZC702_base: Interrupt update
2014-10-30 18:39:49 +02:00
a870603db5
common_bd: Update the common block designs to the new IRQ path
...
Avoid the use of xil_concat module by using the ad_interrupts.
2014-10-27 19:44:25 +02:00
7d3be14ab5
common: Connect audio clkgen reset
...
While we are at it also hide the unused locked pin.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-15 18:44:46 +03:00
fd89458708
common: Set cpu interconnect strategy to minimize area
...
There will rarely be concurrent access to the peripheral control bus
interconnect, so there is no need to optimize for performace. Setting the
interconnect strategy to minimize area can reduce the resource usage by
~90%.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-10-15 18:43:54 +03:00
43e9b0c7a6
common: Disable TTC0 MMIO routing for PS7
...
We do not use the ttc0 to MMIO routing, but it is enabled by default, so
explicitly disable it.
2014-10-10 16:19:51 +03:00
041d8faaf7
common: Updated common projects for ac701/kc702/zc702/zed to vivado 2014.2
2014-09-30 10:31:00 +03:00
41cc92ef49
Remove BASEADDR/HIGHADDR parameters
...
This is unused and unneeded. The AXI interconnect will make sure that a
peripheral only gets requests that are meant for it, there is no need to
check the address in the peripheral itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2014-09-11 12:26:37 +02:00
a49eb5853b
ZED, ZC702: Added contraints so that projects can successfully synthesize on linux systems
...
For ZC706 Fixed one constraint which was not correct
2014-08-26 16:28:41 +03:00
f9a67371c0
Zynq Base System: Reset is synchronized to lowest system clock
...
System reset (sys_100m_reset) is synchronized to lowest system
clock (FCLK0), via a Processor System Reset module
2014-03-26 17:58:14 +02:00
dc44703cf1
zynq/non-zynq: identical signal names and instances
2014-03-17 17:02:03 -04:00
f3ae57a53e
global clock and reset names
2014-03-11 09:57:59 -04:00
ddac1a8834
added common board files
2014-02-28 21:17:01 -05:00
Istvan Csomortani
Lars-Peter Clausen
Rejeesh Kutty
Adrian Costina