The process ad_xcvrcon has a device_clk attribute which can be used to
connect a custom device clock to the XCVR. Fix the proc call so we can
simplify the block design script.
Use the new util_cpack2 and util_upack2 cores. They have lower utilization
that the old util_cpack and util_upack cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
In default strategy we having a few path with small negative slack inside of
the MIG, due to the high UI clock (300MHz).
This new strategy solves this issue.
The loopback on the unused gpio inputs consumes routing resources
while does not gives any value for the software.
Connect these lines to zero instead.
Some projects use the ad_iobuf on IOs that are not bidirectional
producing synthesis warnings.
The change fixes warnings like:
[Synth 8-6104] Input port 'gpio_bd_i' has an internal driver
[Synth 8-6104] Input port 'gpio_status' has an internal driver
- connect unused GPIO inputs to loopback
- connect unconnected inputs to zero
- complete interface for system_wrapper instantiated in all system_top
fixes incomplet portlist WARNING [Synth 8-350]
fixes undriven inputs WARNING [Synth 8-3295]
The change excludes the generated system.v and Xilinx files.
- remove interrupts from system_top
- for all suported carriers:
- remove all interrupt bd pins
- connect to GND all initial unconnected interrupt pins
- update ad_cpu_interrupt procedure to disconnect a interrupt from GND
before connectiong it to another pin.
This change adds the TLAST signal to the AXI streaming interface
of the source side for Intel targets.
Xilinx based designs already have this since the tlast is part of the
interface definition.
In order to make the signal optional and let the tool connect a
default value to the it, the USE_TLAST_SRC/DEST parameter is
added to the configuration UI. This conditions the tlast port on
the interface of the DMAC.
Xilinx handles the optional signals much better so the parameter
is not required there.
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Removes a lot of boilerplate code.
Using the new scheme it is possible to add new projects or sub-projects
without having to re-generate any existing Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The TX side runs on QPLL, and the RX and RX_OS runs on CPLL by default.
The OUTCLK frequency is the same as the REFCLK.
The main reason of this modification is that the links should come up
without any DPR access, after power up, using the default reference clock
configuration (122.88 MHz).
The constraint where added to remove timing problems on the reset path.
The constraint paths do not match anymore. The resets are used in a synchronous
way so we don't need the timing exceptions anyway.
Projects affected by this change:
- daq3
- adrv9739
- ad6676evb
- fmcadc5
- daq2/kcu105
- fmcadc2
- adrv9371x
- fmcomms11/zc706
- fmcjesdadc1
Make sure that the axi_adxcvr instances are configured with the same
transceiver type as the util_adxcvr.
This is necessary for software to be able to detect the transceiver type
and support dynamic reconfiguration.
It is also necessary for correct eye scan support in the axi_adxcvr block.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fix the location assignment of the transceiver blocks to get the correct
lane mapping.
Note that the comments indicating the expected lane mapping are correct,
but the actual transceiver location assignments were not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The external reference clock runs at 122.88 MHz by default. This means that
the QPLL feedback divider needs to be set to 80 so that the VCO is inside
the locking range (9.8 GHz - 16.375 GHz).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Istvan Csomortani
Laszlo Nagy
AndreiGrozav
Lars-Peter Clausen
Adrian Costina
Michael Hennerich