4ce153e6e1
all/system_top.v: loopback gpio lines
...
Create loopback on unused GPIO lines since Linux may rely on it.
2018-10-04 14:19:37 +03:00
2f4904e4d2
motcon2_fmc: Remove muxaddr_out, refclk and refclk_rst from system_bd
...
- refclk and refclk_rst were used for ethernet IDELAY, but are not needed anymore
- muxaddr_out pins overlap with regular GPIOs in the Zed base design. The XADC mux GPIOs can be controlled through that. Cusomters that want to directly control the pins through XADC IP must modify the design
2018-09-05 15:12:51 +03:00
31318cf311
all/system_top.v: drive unused gpio inputs with zero
...
The loopback on the unused gpio inputs consumes routing resources
while does not gives any value for the software.
Connect these lines to zero instead.
2018-08-10 17:00:11 +03:00
ebae8bf8c1
Remove interrupts from system_top for all xilinx projects
...
- remove interrupts from system_top
- for all suported carriers:
- remove all interrupt bd pins
- connect to GND all initial unconnected interrupt pins
- update ad_cpu_interrupt procedure to disconnect a interrupt from GND
before connectiong it to another pin.
2018-08-10 10:10:58 +03:00
6bcbee9a42
motcon2_fmc: Add additional clock constraints and set delays for ethernet
2018-06-14 16:06:43 +03:00
5b222dba02
motcon2_fmc: Connect GPO pins to controller 1
2018-06-14 16:06:38 +03:00
e2df6b75c2
motcon2_fmc: Sync transfer start for the current monitor DMAs
...
There are a maximum of 3 channels enabled for the path, sync start is required
2018-06-14 16:06:24 +03:00
091bbfa2d3
motcon2_fmc: Ethernet MDIO set to EMIO
2018-06-14 16:06:17 +03:00
2975e9a360
motcon2_fmc: Update to revision C
2018-06-14 16:06:07 +03:00
b20714bae2
Regenerate project top-level Makefiles
...
Removes a lot of boilerplate code.
Using the new scheme it is possible to add new projects or sub-projects
without having to re-generate any existing Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2018-04-11 15:09:54 +03:00
377247a434
Regenerate project Makefiles using the new shared Makefile includes
...
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2018-04-11 15:09:54 +03:00
425e803364
license: Fix a spelling mistake
2018-04-11 15:09:54 +03:00
a740b6012f
Make: Use $(MAKE) for recursive make commands
...
This commit should resolve the issue #64 .
Recursive make commands should always use the variable MAKE, not the explicit
command name ‘make’.
2018-03-07 07:40:19 +00:00
d7e87a60a9
Remove executable flag from non-executable files
...
All of these files are source code and are not executable standalone.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2017-07-28 17:56:07 +02:00
b7ca17f02b
scripts: Change adi_project_create to adi_project_xilinx for creating xilinx projects
2017-06-07 12:06:50 +03:00
84b2ad51e2
license: Add some clarification to the header license
2017-05-31 18:18:56 +03:00
85ebd3ca01
license: Update license terms in hdl source files
...
Fix a few gramatical error, fix the path of the top level license
files.
2017-05-29 09:55:41 +03:00
12930c8470
motcon2_fmc: Explicitly assign ETH0 MDIO to EMIO
2017-05-22 18:53:00 +03:00
9055774795
all: Update license for all hdl source files
...
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
2017-05-17 11:52:08 +03:00
f3c0be0868
motcon2_fmc: cleaned up some warnings
2017-04-18 10:33:13 +03:00
24b797f1a6
motcon2: ip automatic version update
2017-04-14 17:11:08 +03:00
1c23cf4621
all: Update verilog files to verilog-2001
2017-04-13 11:59:55 +03:00
c598e84258
remove processing order (no clock def dependency)
2017-02-22 16:02:08 -05:00
d5165ca81f
motcon_fmc: Tie unused pins to GND
2016-12-13 19:20:13 +02:00
9118ca3986
version_upgrade: Update MOTCON2 to 2016.2
2016-09-14 10:58:06 +03:00
0cd608a7e2
lib_refactoring: Update Make files
2016-08-08 16:38:38 +03:00
df36902713
lib_refactoring: Fix path of the IO macros
2016-08-08 15:07:19 +03:00
d60bce654c
Makefiles: Updated Makefiles so they run correctly with gnuwin32 tools
2016-08-05 15:16:04 +03:00
e42b4ea378
hdlmake- updates
2016-08-04 13:28:25 -04:00
7ca8e10004
make: Update Make files
2016-08-01 14:24:48 +03:00
21208ca208
Makefiles: Update Makefiles
2016-03-31 12:37:47 +03:00
7c2f34549b
motcon2_fmc: Update common design to 2015.4
2016-03-23 10:27:07 +02:00
7013b319b0
motcon2_fmc: Fixed reset connection for cpack cores
2015-12-22 12:03:34 +02:00
9d2b8809df
Makefiles: Updated Makefiles
2015-10-23 10:44:27 +03:00
9bb70e2b69
motcon2_fmc: Updated ZED project
2015-10-09 15:33:31 +03:00
83fb5c742a
motcon2_fmc: Updated project to Vivado 2015.2.1
...
- added cpack cores
- removed controller DMA paths
2015-10-09 13:56:41 +03:00
275830d2b1
motcon2_fmc: Drop explicit axi_dmac clock synchronicity configuration
...
The axi_dmac core is now capable of detecting whether its different parts
run in different clock domains or not. No need to configure it manually any
more.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-09-18 15:28:17 +02:00
a679251d7d
Makefiles: Update Make
2015-09-09 17:13:19 +03:00
d52308f074
axi_dmac: Change parameter name 2D_TRANSFER
...
Parameter name can't start with numbers, 2D_TRANSFER was changed to DMA_2D_TRANSFER
2015-08-20 10:14:22 +03:00
57cfb7cfb1
hdl/library: Update the IP parameters
...
The following IP parameters were renamed:
PCORE_ID --> ID
PCORE_DEVTYPE --> DEVICE_TYPE
PCORE_IODELAY_GROUP --> IO_DELAY_GROUP
CH_DW --> CHANNEL_DATA_WIDTH
CH_CNT --> NUM_OF_CHANNELS
PCORE_BUFTYPE --> DEVICE_TYPE
PCORE_ADC_DP_DISABLE --> ADC_DATAPATH_DISABLE
CHID --> CHANNEL_ID
PCORE_DEVICE_TYPE --> DEVICE_TYPE
PCORE_MMCM_BUFIO_N --> MMCM_BUFIO_N
PCORE_SERDES_DDR_N --> SERDES_DDR_N
PCORE_DAC_DP_DISABLE --> DAC_DATAPATH_DISABLE
DP_DISABLE --> DATAPATH_DISABLE
PCORE_DAC_IODELAY_ENABLE --> DAC_IODELAY_ENABLE
C_BIG_ENDIAN --> BIG_ENDIAN
C_M_DATA_WIDTH --> MASTER_DATA_WIDTH
C_S_DATA_WIDTH --> SLAVE_DATA_WIDTH
NUM_CHANNELS --> NUM_OF_CHANNELS
CHANNELS --> NUM_OF_CHANNELS
PCORE_4L_2L_N -->QUAD_OR_DUAL_N
C_ADDRESS_WIDTH --> ADDRESS_WIDTH
C_DATA_WIDTH --> DATA_WIDTH
C_CLKS_ASYNC --> CLKS_ASYNC
PCORE_QUAD_DUAL_N --> QUAD_DUAL_N
NUM_CS --> NUM_OF_CS
PCORE_DAC_CHANNEL_ID --> DAC_CHANNEL_ID
PCORE_ADC_CHANNEL_ID --> ADC_CHANNEL_ID
PCORE_CLK0_DIV --> CLK0_DIV
PCORE_CLK1_DIV --> CLK1_DIV
PCORE_CLKIN_PERIOD --> CLKIN_PERIOD
PCORE_VCO_DIV --> VCO_DIV
PCORE_Cr_Cb_N --> CR_CB_N
PCORE_VCO_MUL --> VCO_MUL
PCORE_EMBEDDED_SYNC --> EMBEDDED_SYNC
PCORE_AXI_ID_WIDTH --> AXI_ID_WIDTH
PCORE_ADDR_WIDTH --> ADDRESS_WIDTH
DADATA_WIDTH --> DATA_WIDTH
NUM_OF_NUM_OF_CHANNEL --> NUM_OF_CHANNELS
DEBOUNCER_LEN --> DEBOUNCER_LENGTH
ADDR_WIDTH --> ADDRESS_WIDTH
C_S_AXIS_REGISTERED --> S_AXIS_REGISTERED
Cr_Cb_N --> CR_CB_N
ADDATA_WIDTH --> ADC_DATA_WIDTH
BUFTYPE --> DEVICE_TYPE
NUM_BITS --> NUM_OF_BITS
WIDTH_A --> A_DATA_WIDTH
WIDTH_B --> B_DATA_WIDTH
CH_OCNT --> NUM_OF_CHANNELS_O
M_CNT --> NUM_OF_CHANNELS_M
P_CNT --> NUM_OF_CHANNELS_P
CH_ICNT --> NUM_OF_CHANNELS_I
CH_MCNT --> NUM_OF_CHANNELS_M
4L_2L_N --> QUAD_OR_DUAL_N
SPI_CLK_ASYNC --> ASYNC_SPI_CLK
MMCM_BUFIO_N --> MMCM_OR_BUFIO_N
SERDES_DDR_N --> SERDES_OR_DDR_N
CLK_ASYNC --> ASYNC_CLK
CLKS_ASYNC --> ASYNC_CLK
SERDES --> SERDES_OR_DDR_N
GTH_GTX_N --> GTH_OR_GTX_N
IF_TYPE --> DDR_OR_SDR_N
PARALLEL_WIDTH --> DATA_WIDTH
ADD_SUB --> ADD_OR_SUB_N
A_WIDTH --> A_DATA_WIDTH
CONST_VALUE --> B_DATA_VALUE
IO_BASEADDR --> BASE_ADDRESS
IO_WIDTH --> DATA_WIDTH
QUAD_DUAL_N --> QUAD_OR_DUAL_N
AXI_ADDRLIMIT --> AXI_ADDRESS_LIMIT
ADDRESS_A_DATA_WIDTH --> A_ADDRESS_WIDTH
ADDRESS_B_DATA_WIDTH --> B_ADDRESS_WIDTH
MODE_OF_ENABLE --> CONTROL_TYPE
CONTROL_TYPE --> LEVEL_OR_PULSE_N
IQSEL --> Q_OR_I_N
MMCM --> MMCM_OR_BUFR_N
2015-08-19 14:11:47 +03:00
b84afcdcd1
Merge branch 'master' into dev
...
Conflicts:
library/Makefile
library/axi_ad6676/axi_ad6676_ip.tcl
library/axi_ad9122/axi_ad9122_core.v
library/axi_ad9122/axi_ad9122_ip.tcl
library/axi_ad9144/axi_ad9144_ip.tcl
library/axi_ad9152/axi_ad9152_ip.tcl
library/axi_ad9234/axi_ad9234_ip.tcl
library/axi_ad9250/axi_ad9250_hw.tcl
library/axi_ad9250/axi_ad9250_ip.tcl
library/axi_ad9361/axi_ad9361.v
library/axi_ad9361/axi_ad9361_dev_if_alt.v
library/axi_ad9361/axi_ad9361_ip.tcl
library/axi_ad9361/axi_ad9361_rx_channel.v
library/axi_ad9361/axi_ad9361_tdd.v
library/axi_ad9361/axi_ad9361_tx_channel.v
library/axi_ad9625/axi_ad9625_ip.tcl
library/axi_ad9643/axi_ad9643_channel.v
library/axi_ad9643/axi_ad9643_ip.tcl
library/axi_ad9652/axi_ad9652_channel.v
library/axi_ad9652/axi_ad9652_ip.tcl
library/axi_ad9671/axi_ad9671_constr.xdc
library/axi_ad9671/axi_ad9671_ip.tcl
library/axi_ad9680/axi_ad9680_ip.tcl
library/axi_ad9739a/axi_ad9739a_ip.tcl
library/axi_dmac/axi_dmac_constr.sdc
library/axi_hdmi_tx/axi_hdmi_tx_ip.tcl
library/axi_jesd_gt/axi_jesd_gt_constr.xdc
library/axi_jesd_gt/axi_jesd_gt_ip.tcl
library/axi_mc_speed/axi_mc_speed_constr.xdc
library/common/ad_gt_channel_1.v
library/common/ad_gt_common_1.v
library/common/ad_gt_es.v
library/common/ad_iqcor.v
library/common/ad_jesd_align.v
library/common/ad_rst.v
library/common/altera/ad_xcvr_rx_rst.v
library/common/up_adc_common.v
library/common/up_axis_dma_rx.v
library/common/up_axis_dma_tx.v
library/common/up_clkgen.v
library/common/up_clock_mon.v
library/common/up_dac_common.v
library/common/up_gt.v
library/common/up_hdmi_tx.v
library/common/up_tdd_cntrl.v
library/common/up_xfer_cntrl.v
library/common/up_xfer_status.v
library/util_cpack/util_cpack.v
library/util_cpack/util_cpack_ip.tcl
library/util_dac_unpack/util_dac_unpack_hw.tcl
library/util_jesd_align/util_jesd_align.v
library/util_jesd_xmit/util_jesd_xmit.v
library/util_upack/util_upack_ip.tcl
library/util_wfifo/util_wfifo.v
library/util_wfifo/util_wfifo_constr.xdc
library/util_wfifo/util_wfifo_ip.tcl
projects/arradio/c5soc/system_bd.qsys
projects/common/vc707/vc707_system_bd.tcl
projects/common/zc706/zc706_system_plddr3.tcl
projects/daq2/a10gx/Makefile
projects/daq2/a10gx/system_bd.qsys
projects/daq3/common/daq3_bd.tcl
projects/daq3/zc706/system_bd.tcl
projects/fmcjesdadc1/a5gt/Makefile
projects/fmcjesdadc1/a5gt/system_bd.qsys
projects/fmcjesdadc1/a5gt/system_constr.sdc
projects/fmcjesdadc1/a5gt/system_top.v
projects/fmcjesdadc1/a5soc/system_bd.qsys
projects/fmcjesdadc1/common/fmcjesdadc1_bd.tcl
projects/fmcomms1/ac701/system_bd.tcl
projects/fmcomms1/common/fmcomms1_bd.tcl
projects/fmcomms1/kc705/system_bd.tcl
projects/fmcomms1/vc707/system_bd.tcl
projects/fmcomms1/zc702/system_bd.tcl
projects/fmcomms1/zc702/system_top.v
projects/fmcomms1/zc706/system_bd.tcl
projects/fmcomms1/zc706/system_top.v
projects/fmcomms1/zed/system_bd.tcl
projects/fmcomms1/zed/system_top.v
projects/fmcomms2/ac701/system_constr.xdc
projects/fmcomms2/common/fmcomms2_bd.tcl
projects/fmcomms2/kc705/system_constr.xdc
projects/fmcomms2/kc705/system_top.v
projects/fmcomms2/mitx045/system_top.v
projects/fmcomms2/rfsom/system_constr.xdc
projects/fmcomms2/rfsom/system_top.v
projects/fmcomms2/vc707/system_top.v
projects/fmcomms2/zc706/system_bd.tcl
projects/fmcomms2/zc706/system_constr.xdc
projects/fmcomms2/zc706/system_top.v
projects/fmcomms2/zed/system_top.v
projects/imageon/zc706/system_constr.xdc
projects/motcon2_fmc/common/motcon2_fmc_bd.tcl
projects/motcon2_fmc/zed/system_constr.xdc
projects/motcon2_fmc/zed/system_top.v
projects/usdrx1/a5gt/Makefile
projects/usdrx1/a5gt/system_bd.qsys
projects/usdrx1/common/usdrx1_bd.tcl
Conflicts were resolved using 'Mine' (/dev).
2015-08-17 15:15:58 +03:00
17b2a9f121
Merge branch 'master'
...
Merge master into release to sync the index files. The two changes are just mode changes. There aren't any functional changes in this commit!
2015-08-17 10:09:07 +03:00
afb9911b6e
Makefiles: Updated makefiles
2015-08-06 19:50:50 +03:00
a7da779b94
Makefile: Updated Makefiles
2015-07-16 18:19:42 +03:00
c972779217
motcon2_fmc: updated util_gmii_to_rgmii and motcon2_fmc project for improved performance of the ethernet
...
- removed the delay controller from the top file and added it inside the util_gmii_to_rgmii core
- removed delay related xdc constraints as they are not needed
2015-07-08 16:23:33 +03:00
c372064302
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-07-01 18:43:51 +02:00
499357a65a
motcon2_fmc: Updated project to include XADC
...
- connected reset pin, as vivado reports the reset pin erroneously
- configured XADC in simultaneous sampling mode from XAUX0 and XAUX8
- connected XADC interrupt
- because in the project constraints some base pin constraints are overwritten, the project constraints are processed late
- GPI pins were assigned instead of the XADC GIO0 and GIO1, which were assigned to the XADC for external mux mode
- removed commented code
2015-06-29 16:56:25 +03:00
6862655b0d
Add .gitattributes file
...
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2015-06-26 11:07:10 +02:00
2e46bda916
motcon2_fmc: Update project to use the latest util_gmii_to_rgmii
2015-06-16 17:43:10 +03:00
77eff35d67
motcon2_fmc: Fixed constraint for renamed port
2015-05-23 19:02:48 +03:00
Laszlo Nagy
Adrian Costina
AndreiGrozav
Lars-Peter Clausen
Istvan Csomortani
Rejeesh Kutty