SPI Engine: create inverted CS mode
Add a CS Invert Mask instruction for selecting the polarity of
the Chip Select pins.
Signed-off-by: Laez Barbosa <laez.barbosa@analog.com>
* SPI Engine: Add registers for Offload memory and FIFO sizes
Adds registers at dword 0x04 and 0x05, respectively allowing software
to get the sizes of the Offload Module memories (command and sdo) or
the sizes of the FIFOs on the AXI regmap.
Signed-off-by: Laez Barbosa <laez.barbosa@analog.com>
Use tcl script instead of static xmls for the interface.
Easier to maintain and are not gitignored.
Rename spi_master to spi_engine because every interface should be
prefixed by the IP name; in this case, spi_engine.
Also, remove interface/*.sv files on make clean and git ignore them.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
* Added header license for the files that didn't have
* Modified parentheses
* Removed extra spaces at the end of lines
* Fixed parameters list to be each parameter on its line
* Deleted lines after endmodule and consecutive empty lines
* Fixed indentation
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
The 4 parameters are added to facilitate transmiting project
related information to the software. They act as read-only
memory which is written in Vivado when the project builds.
Set 31 to SDI FIFO's almost full threshold
This reverts commit 0402ce85e4
and reverts commit 164aa97ec3.
The trigger pulse generation must be handled outside of the
SPI Engine framework.
It is recommanded to be done in system level using a PWM
generator or an external signal.
Define both AXI4 Memory Mapped and microprocessor interface for the
reigster map, then activate/deactive one of it in fucntion of the memory
interface type parameter.
Define the missing status_sync interface, which should be connected to
the offload.
Context switching with a parameter is not a good idea. The simulator
may evaluate both branch of the IF statement, even though the inactive
branch may not be valid.
Use if..generate to make the code more robust for both synthesizers and
simulators.
Fix the *_ip.tcl scripts for axi_spi_engine and spi_engine_offload
module.
In case of a bool parameters the value_format and value properties must
be set for both user and hdl paramters. If not, in the generated verilog
code the tool will use "true" or "false" strings, instead of 0 or 1.
The value of the HDL parameter NUM_OF_SDI can be read out from the
register at address 0x0C. The same register contains the value of the
DATA_WIDTH.
The register has the following bit layout:
[15: 0] DATA_WIDTH
[23:16] NUM_OF_SDI
[31:24] 8'b0
Forward the offload's sync_id to the register map, by defining an
additional AXI stream interface between the offload and axi_spi_engine.
The last sync_id of the offload module can read out from the
register 0x00C4. It also can generate and interrupt if the irq mask is
configured accordingly.
The pulse period had a fixed value. Therefore, in order to be able
to configure it from the software, a 32b register pulse_period_reg
was added in axi_spi_engine. Also, to generate the pulse, the
output register pulse_gen_loadc was added.
The ready signal of the SYNC interface should be always 1'b1,
regardless of ASYNC_SPI_VALUE.
Drive the ready with one in both branches of the ASYNC_SPI_CLK
generate block.
Add additional synchronization FIFOs to several interfaces of the
axi_spi_engine module, to prevent metastability and timing issues in
case when the system clock and the SPI clock are asynchronous.
LBFFilho
Jorge Marques
Iulia Moldovan
Iacob_Liviu
Nick Pillitteri
sergiu arpadi
Laszlo Nagy
Adrian Costina
Istvan Csomortani
stefan.raus
Stanca Pop