+ Build both the read and write logic around an FSM
+ Consistent naming of registers and wires
+ Add support for burst lenghts higher than one, current burst lenght
is 64
+ Fix all the bugs, and make it work (first bring up with
adrv9371x/a10soc)
The DDR memory reference clock on the A10SoC development board is
differential. Currently the EMIF core it is configured for single-ended
configuration, which causes it to generate incorrect IOSTANDARD
constraints. Those incorrect constraints get overwritten again in
system_assign.tcl, so things are working, but this generates a warning when
building the design
Configure the EMIF core correctly and remove the manual constraint overwrite since
they are no longer necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
There is no guarantee that the external reset de-assertion is synchronous
to the sys_clk, yet the clock bridge marks the reset de-assertion as
synchronized to the clock. This can cause recovery or removal timing
violations for the registers affected by this reset signal and potentially
bring the system into an invalid state after the reset is de-asserted.
Mark the reset as not synchronized to the clock signal, this will make sure
that Qsys inserts the proper reset synchronizers where required.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
While things seem to work fine with only specifying the the IO standard for
the positive side of differential signals Quartus will issue a warning
about incomplete constraints if the IO standard is not specified for the
the neagtive side as well. To avoid these warnings add the missing
constraints.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fix a copy and paste error and specify the IO_STANDARD for all gpio_bd_i
rather than twice for half of them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Both the sys_hps.f2sdram_clock and the sys_dma_clk.clk signal are in the
same clock domain. They are both driven by the same clock. And even though
qsys is capable of detecting this it seems qsys interconnect is not able to
infer this and inserts a extra clock domain crossing bridge between the DMA
and the HPS AXI system memory interface.
To avoid this connect the sys_dma_clk.clk to the sys_hps.f2sdram_clock so
that all components are driven by the same qsys clock signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
There is no need for the audio clock to be phase aligned to its source
clock. When phase alignment is disabled the MMCM uses an internal feedback
path without requiring external resources, so disable it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Depending on the configuration of the clock source type of the input clock
the clocking wizard will instantiate all kinds of buffers on the input
clock signal.
For these particular projects there is no need to add any kind of buffer
since the source is already coming from a global clock buffer. So set the
configuration accordingly.
Avoids the following warning:
[Opt 31-32] Removing redundant IBUF since it is not being driven by a
top-level port. i_system_wrapper/system_i/sys_audio_clkgen/inst/clkin1_ibufg
Resolution: The tool has removed redundant IBUF. To resolve this
warning, check for redundant IBUF in the input design.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Instead of manually specifying the input clock frequency let the core infer
it automatically. This makes it more straight forward to change the clock
frequency.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Istvan Csomortani
Adrian Costina
STEVE KRAVATSKY
AndreiGrozav
Rejeesh Kutty
Lars-Peter Clausen
Nick Pillitteri