Software has to know which TIA channel was used for a particular capture.
Define an additional dummy ADC channel which will provide this
information. Currently this channel is always enabled.
This commit was created by squashing the following commits, these
messages were kept just for sake of history:
ad9694_500ebz: Mirror the SPI interface to FMCB
ad9694_500ebz: Set transceiver reference clock to 250
ad9694_500ebz: Allow to configure number of lanes, number of converters
and sample rate
axi_ad9694: Fix number of lanes, it must be 2
ad9694_500ebz: Update the mirrored spi pin assignments
ad9694_500ebz: Gate SPI MISO signals based on chip-select
ad9694_500ebz: Set channel pack sample width
ad9694_500ebz: Change reference clock location
ad9694_500ebz: Remove transceiver memory map arbitration
ad9694_500ebz: Ensure ADC FIFO DMA_DATA_WIDTH is not larger ADC_DATA_WIDTH
ad9694_500ebz: Adjust breakout board pin locations
ad_fmclidar1_ebz: Rename the ad9694_500ebz project
ad_fmclidar1_ebz: Fix lane mapping
ad_fmclidar1_ebz: Delete deprecated files
ad_fmclidar1_ebz: Integrate the axi_laser_driver into the design
ad_fmclidar1_ebz: OTW is an active low signal
ad_fmclidar1_ebz: zc706: Fix iic_dac signals assignment
ad_fmclidar1_ebz: Switch to util_adcfifo
ad_fmclidar1_ebz: Enable synced capture for the fifo
ad_fmclidar1_ebz/zc706: Enable CAPTURE_TILL_FULL
ad_fmclidar1_ebz/zc706: Reduce FIFO size to 2kB
ad_fmclidar1_ebz: Laser driver runs on ADC's core clock
ad_fmclidar1_ebz_bd: Delete the FIFO instance
Because the DMA transfers are going to be relatively small (< 2kbyte),
the DMA can handle the data rate, even when the frequency of the laser
driver pulse is set to its maximum value. (200 kHz)
The synchronization will be done by connecting the generated pulse to
the DMA's SYNC input. Although, to support 2 or 1 channel scenarios, we
need to use the util_axis_syncgen module to make sure that the DMA
catches the pulse, in cases when the pulse width is too narrow. (SYNC is
captures when valid and ready is asserted)
Also we have to reset the cpack IP before each pulse, to keep the DMA buffer's
relative starting point in time fixed, when only 2 or 1 channel is
active.
The module can receive a synchronous or asynchronous pulse with an arbitrary
width and generate a SYNC signal for the DMA Source AXI Streaming interface.
This way we can synchronize the DMA transfers to an external
pulse/signal.
The laser driver contains the axi_pulse_gen's IP and an additional
register map which controls/monitor the laser driver enable control line
and the over temperature warning line (OTW).
It also contains an interrupt logic, which allows to generate an
interrupt in function of the generated pulse or incoming OTW signal.
The IPs register maps looks as follow:
0x00 - axi_pulse_gen register map
0x80 - axi_laser_driver register map
0x80 - DRIVER_ENABLE
0x84 - DRIVER_OTW
0x88 - EXT_CLK_COUNTER
0xA0 - IRQ_MASK
0xA4 - IRQ_SOURCE
0xA8 - IRQ_PENDING
0xAC - SEQUENCER_CONTROL
0 - SEQUENCER_ENABLE
1 - AUTO_SEQUENCER_ENABLED
0xB0 - SEQUENCER_SYNC_OFFSET
0xB4 - AUTO_SEQUENCE
[ 1: 0] - CHANNEL_SEL_0
[ 5: 4] - CHANNEL_SEL_1
[ 9: 8] - CHANNEL_SEL_2
[13:12] - CHANNEL_SEL_3
0xB8 - MANUAL_SEQUENCE
[ 1: 0] - MANUAL_CHANNEL_SEL
Current interrupt sources scheme is:
- bit 0 : pulse (triggered by the level of the pulse)
- bit 1 : OTW_N enter (triggered by positive edge of the OTW_N)
- bit 2 : OTW_N exit (triggered by the level of the pulse)
Generate a reset signal before the pulse which can be used to reset
various IP's of the data path (eg. pack/cpack). This can help to clear out the
internal buffers and registers of these IP, starting clean at the moment when
the actual pulse arrives.
The sequencer has an auto and a manual mode, and can be set to custom
sequences of the TIA channel selection lines sate.
The sequencer in auto mode is synchronized to the pulse, it will change
its state before a generated pulse which will drive the lasers. The
offset between the sequencer beat and the laser driver pulse can be
modified through an AXI register.
- add missing false paths
- change the bus skew constraint to a false path, for some reason the
tool does not change the path's requirement after a set_bus_skew
constraint
Our internal repository was changed from phdl to ghdl. Update the
adi_env.tcl scripts and other scripts, which depends on the $ad_ghdl_dir
variable. This way the tools will see all the internal IPs too.
Istvan Csomortani
Arpadi
Adrian Costina
AndreiGrozav
István Csomortáni
Laszlo Nagy